Page 1
SERVICE MANUAL 50" DIGITAL PLASMA COLOR TELEVISION 50HP16 The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2).
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
SERVICING NOTICES ON CHECKING When you remove the cover, do not scratch the 1. KEEP THE NOTICES FPC on both ends of PDP Module. As for the places which need special attentions, Hold the four ends holder and be careful not to they are indicated with the labels or seals on the touch the glass area.
HOW TO ORDER PARTS Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER.
TABLE OF CONTENTS GREEN PRODUCT PROCUREMENT ..................A1-1 LEAD-FREE SOLDER ........................ A1-1 SERVICING NOTICES ON CHECKING ..................A1-2 HOW TO ORDER PARTS ......................A1-3 IMPORTANT ..........................A1-3 PANEL LOCK ..........................A1-3 TABLE OF CONTENTS ......................A2-1 GENERAL SPECIFICATIONS ....................A3-1~A3-5 DISASSEMBLY INSTRUCTIONS 1.EXCHANGE METHOD OF PDP MODULE ................
Page 6
GENERAL SPECIFICATIONS PDP Size / Visual Size 49.95 inch / 1268.7 mmV System Number of Pixels(H x V) 1366(H) x 768(V) Color System NTSC Speaker 4 Speaker Position Front Main Size 2.2 x 5.0 inch Impedance 4 ohm Tweeter Size 2.0 inch Impedance 8 ohm...
Page 7
GENERAL SPECIFICATIONS Remote Unit RC-KK Control Glow in Dark Remocon Remocon Format TOSHIBA Format TOSHIBA Custom Code 40-BF h Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys Keys Power Input Display Mute 100 / +10...
GENERAL SPECIFICATIONS G-10 Features Auto Shut Off Power On Memory Auto Search Comb Filter Just Clock Function Game Position Auto Setup(Language/CH Program) Picture Setting(TV) Mode(Picture Preference) Brightness , Contrast , Color Tint Sharpness Color Temperature Cable Clear Picture Setting(PC) BRIGHTNESS , CONTRAST HOR POSITION , VER POSITION PHASE , CLOCK AUTO ADJUST...
DISASSEMBLY INSTRUCTIONS 1. EXCHANGE METHOD OF PDP MODULE NOTE Do handling with the PDP Module by 2 persons. REMOVAL METHOD OF PDP MODULE 1-1: CABINET BACK/COVER BACK Remove the screw. Remove the Cabinet Back and Cover Back. Cabinet Back Cover Back 1-2: STAND ASS'Y Spread a sheet on the plane table and place the PDP Module carefully with the panel face down.
Page 12
DISASSEMBLY INSTRUCTIONS 1-3: CHASSIS BLOCK Disconnect the connector. Remove the screw. Remove the Chassis Ass'y. Chassis Ass'y 1-4: PDP MODULE Remove the screw. Remove the Side Jack. Hold the Frame Main carefully and remove the PDP Module. NOTE When removing the PDP Module, raise the cushion carefully so that you do not scratch the face. Raise the cushion.
Page 13
DISASSEMBLY INSTRUCTIONS 1-5: PDP FILTER Remove the screw. Remove the Shield Main. Remove the PDP Filter. Shield Main Top PDP Filter Shield Main L Shield Main R Shield Main Bottom B1-3...
Page 14
DISASSEMBLY INSTRUCTIONS INSTALLATION METHOD OF PDP MODULE NOTES FOR NEW PDP FILTER HANDLING When you handle the PDP Filter, you must wear gloves to avoid soiling it with sweat and dust. When you lift the PDP Filter, use the palm of your hand. Don’t pick it up with your fingers. The back side of the PDP Filter tends to get damaged, since there is no coating.
Page 15
DISASSEMBLY INSTRUCTIONS NOTES FOR NEW PDP MODULE HANDLING Handle the PDP Module with 2 people. There is a step difference between the cover and the PDP Module, so when you remove the screws, place a cushion on it to keep the PDP Module from being scratched. Then remove the screws carefully. When you remove the cover, do not scratch the FPC on both ends of PDP Module.
Page 16
DISASSEMBLY INSTRUCTIONS 1-7: PDP MODULE (PREPARATION) Remove the fixing screw of PCB. Assemble the Wiring Clip. (Use the clips on defective PDP Module) Assemble the Cord Clip. (Use the clips on defective PDP Module) Cord Clip Wiring Clip 90˚ 90˚ Set CN201 (24V) B1-6...
Page 17
DISASSEMBLY INSTRUCTIONS 1-8: PDP MODULE Assemble the Frame Main. (Use the clips on defective PDP Module) Install the PDP Filter on the set. Install the Shield Main on the set. Hold the Frame Main carefully and install the New PDP Module on the set. Install the Side Jack on the set.
Page 18
DISASSEMBLY INSTRUCTIONS 1-9: CHASSIS BLOCK Do the wire fixing as shown in the photo, then install the Chassis Ass'y. Install the Stand Ass'y. Earth wire of AC Inlet. Sheet Earth Mark Earth wire Band Cord Clamp Band Cord Clamp 1-10: CABINET BACK/COVER BACK Check if the wire handlings are correct.
DISASSEMBLY INSTRUCTIONS When IC starts moving back and forth easily after REMOVAL AND INSTALLATION OF desoldering completely, pickup the corner of the IC using a FLAT PACKAGE IC tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put Masking Tape (cotton tape) around the Flat Package...
Page 20
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.) IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit and on the remote control for more than the standard time in the appropriate condition.
WHEN REPLACING EEPROM (MEMORY) IC CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS, MICON VERSION AND DIGITAL TV MICON FIRMWARE Initial total of MEMORY IC, POWER ON total hours, MICON VERSION and Digital TV MICON Firmware can be checked on the screen.
FUNCTION OF PCB CTRL Y SUS 50 SONY PSU TDRV TOP Z SUS POWER YDRV BOT XRLT XRCT XRRT 50 SONY PSU A supplier which supplies voltage and current to each PCB and Panel. Y SUS According to the timing provided from Panel Control, switches FETs and generates driving waveform signal which is provided to Y electrode through Scan Driver IC of TDRV TOP and TDRV BOT.
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE FUNCTION FUNCTION H POSI OSD B DRIVE (W) Read and perform these adjustments when repairing the V POSI OSD B CUT OFF (W) circuits or replacing electrical parts or PCB assemblies. R DRIVE (N) H POSI 60Hz V POSI 60Hz CAUTION R CUT OFF (N)
Page 25
ELECTRICAL ADJUSTMENTS 2-2: WHITE BALANCE Place the set in Aging Test for more than 15 minutes. Receive the gray scale pattern from the Pattern Generator. Press the INPUT button on the remote control to set to the AV mode. Using the remote control, set the brightness and contrast to normal position.
Page 26
ELECTRICAL ADJUSTMENTS 2-4: Confirmation of Fixed Value (Step No.) Please check if the fixed values of each the adjustment items are set correctly referring below. (TV/AV/YUV/HDMI/PC/DTV) HD-MI SVGA WXGA WVGA WXGA 480i 480p 720p 1080i 480i 480p 720p 1080i 60*480 800*600 1024*768 1280*768...
TROUBLESHOOTING GUIDE POWER DOES NOT TURN ON CHANGE F3900. IS F3900 BROKEN ? IS THERE VOLTAGE CHECK CP3201 AND AT PIN 11 OF CP3201 CP3804. 5V ? CHECK IC3804 AND IS THERE VOLTAGE AT PIN 2 OF IC3804 PERIPHERAL CIRCUIT. OR CHANGE AV PCB.
Page 29
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (1). CONNECT CP3201. IS CD3201 CONNECTED ? IS CD7204 CONNECTED ? CONNECT CD7202. IS THERE SIGNAL CHANGE IC7202. AT IC7202 ? CHECK IC801. OR CHANGE SCALER PCB.
Page 30
TROUBLESHOOTING GUIDE THE PICTURE DOES NOT APPEAR (2). CHECK IC4201 AND IS THERE SIGNAL PERIPHERAL CIRCUIT. AT IC4201 ? CONNECT CD4203. IS CD4203 CONNECTED CHECK IC4201 AND AND IS THERE SIGNAL ? PERIPHERAL CIRCUIT. CHECK IC801 AND PERIPHERAL CIRCUIT.
Page 31
TROUBLESHOOTING GUIDE THE PICTURE APPEARS, BUT THE AUDIO DOES NOT APPEAR. IS CD301 AND CD303 CONNECT CD301 AND CD303. CONNECTED ? IS THERE SIGNAL CHANGE SP301 AND SP302. CD301 AND CD303 ? IS THERE SIGNAL CHECK IC301 AND AT PINS 11 AND 15 PERIPHERAL CIRCUIT.
Page 32
TROUBLESHOOTING GUIDE THE STOP PICTURE "PLEASE WAIT". CONNECT CD3806. IS CD3806 CONNECTED ? IS DIGITAL PCB CONNECT DIGITAL PCB. CONNECTED ? IS THERE VOLTAGE CHECK Q512, IC509 AND AT PINS 1 AND 2 OF PERIPHERAL CIRCUIT. CD3806 5V ? CHANGE DIGITAL PCB.
Page 33
TROUBLESHOOTING GUIDE THE COLOR DOES NOT APPEAR. IS SETTING OF CHANGE THE SETTING OF COLOR NORMAL ? COLOR. IS THE COLOR RECEIVE THE COLOR SIGNAL. SIGNAL RECEIVED ? CHECK IC801 AND IS THERE SIGNAL PERIPHERAL CIRUCUIT. AT IC801 ? CHECK IC2101 AND IS THERE SIGNAL PERIPHERAL CIRUCUIT.
Page 34
TROUBLESHOOTING GUIDE ON SCREEN DISPLAY DOES NOT APPEAR. IS THERE SIGNAL AT CHECK IC101 AND PINS 2, 3, 4 AND 5 OF PERIPHERAL CIRCUIT. IC101 ? IS THE COLOR SIGNAL CHECK IC801AND AT PINS 57, 58, 59 AND PERIPHERAL CIRCUIT. 60 OF IC801 ? CHANGE SCALER PCB.
SIDE JACK PCB SCHEMATIC DIAGRAM (SIDE JACK PCB) R4493 SIDE VIDEO JACK FROM/TO AV SWITCH2 J4207 AV-5A-66H CP4200 (CP4201) B4208 A2001WV2-8P BLM18BB600SN1 SIDE_A_IN_R FRONT AUDIO L JACK J4208 SIDE_A_IN_L AV-5A-68H R6504 L4200 SIDE_V_IN 22uH SIDE_S_C SIDE_S_Y C6543 SIDE_S_L 0.001 B SIDE AUDIO R JACK J4209 AV-5A-67H...
WAVEFORMS TUNER ADC1 2.0ms 20 s 20ns 2.0V 1.0V 1.0V SOUND AMP/HEADPHON AMP STEREO 2.0ms 2.0ms 2.0ms 2.0V 500mV 500mV AV SWITCH2 100 s 2.0ms 2.0ms 2.0V 500mV 500mV MICON 100 s 2.0ms 50ns 2.0V 2.0V 500mV SCALER 2.0ms 20 s 20 s 2.0V 500mV...
Page 75
WAVEFORMS ADC1 20 s 20 s 500mV 500mV 500mV 10 s 20 s 2.0V 500mV 500mV ADC1 20 s 2.0V 200mV 500mV JACK INTERFACE_HDMI IC 20 s 1.0ms 20 s 200mV 1.0V 1.0V 20 s 1.0ms 20 s 200mV 1.0V 1.0V The following waveforms were measured at the point of the corresponding NOTE:...
Page 76
WAVEFORMS ASIC 20 s 10ns 1.0V 50mV AV OUT 20ns 2.0V 50mV LVDS 10ms 2.0V 100mV 2.0V 20 s 1.0V The following waveforms were measured at the point of the corresponding NOTE: balloon number in the schematic diagram.