Related Manuals for Husqvarna SC18/968981201
Summary of Contents for Husqvarna SC18/968981201
- Page 1 Operators manual Please read these instructions carefully and make sure you understand them before using the machine. MANUAL NO. 540200156 REV. 01 (12/01/05) Models: SC18/968981201 SC18/968999352...
-
Page 2: Table Of Contents
Index Operator’s Guide Page Specifications ... 2 Features and Controls ... 3 General Operating Instructions ... 4 Warnings ... 4 Operating Instructions Page Operator’s Tips ... 4 Operating on Hills ... 5 Before You Start ... 5 Transporting ... 5 Sod Cutting ... -
Page 3: Features And Controls
Oil used in the engine (gray cap) 1. Refer to your engine manual for oil type, viscosity, weight Oil used in the Clutch/Gear Box Transmission grease used FEATURES AND CONTROLS and capacity. 1. Refer to your engine manual for oil type, viscosity, weight and capacity. -
Page 4: General Operating Instructions
GENERAL INFORMATION This manual will assist you in the safe operation and proper maintenance of your Husqvarna equip- ment. Read it thoroughly before attempting to operate the machine. Do not hesitate to call your dealer or Husqvarna if additional information is required. -
Page 5: Operating On Hills
• Do not attempt sharp turns while cutting. • Should I water before cutting? It is usually not necessary to water before cutting. In extreme conditions, such as clay soil that is very compacted, a simple test as follows will determine if you need to water before cutting. Use a garden hand spade, weed tool, or even a large screwdriver to test the ground’s hardness. -
Page 6: Safety And Maintenance
Husqvarna parts have been designed and specified to meet commercial operating standards for strength and durability. For reliability and preservation of design safety standards, replacements should only be made with genuine Husqvarna parts or material of equivalent type and strength. TWO MINUTE WARNING Sod Cutters may be tipped on their engine guard for cleaning and access for no more than 2 minutes. -
Page 7: Blade Wear
SERVICE AND MAINTENANCE BLADE WEAR Sod cutter blades may wear quickly depending on soil condition. Replace blade when worn to 1 1/2” (3.8cm) or less. Maintain lower blade surface. CLEANING AND WASHING Regular cleaning and washing will prolong the service of your machine. Note: Use care with power washers to avoid damage to Warning Decals, Operator Instruction Labels, Bearings, Chain and Engine. -
Page 8: Trouble Shooting Guide
PROBLEM Transmission shaft broke Drive wheels won’t engage Unit jumps out of gear Bushings on depth control assembly1. The bushings are wearable items. are wearing quickly. Bushings “ooze out” when installed 1. This is normal. Trim with knife if desired. Right Angle T-drive leaking What RPM should my engine be set to? - Page 9 2. Make sure the blade is sharp. 3. Moisture, oil or grease on the belt will cause it to slip. Replace with a Husqvarna belt. 4. Tension can be increased by tightening the Cable Tension Nut. If additional adjustment is not available, add a 1/2”...
- Page 10 Belt Keeper when engaged. 2. Be sure the correct Husqvarna belt is being used. If not, replace with a Husqvarna belt. 3. Belt Idler Pivot Bolt may be too tight or need lubrication.
- Page 11 PROBLEM Belt glazed or slipping Depth Control Rod broke Depth Control Rod will not turn (frozen) Unit is creeping Handle Stand Off Kit - how to tighten bolts Bolts breaking Tires wearing too quickly TROUBLESHOOTING ANSWER/COMMENT 10. Be sure the Belt Idler Assembly is adjusted correctly. See Technical Bulletin “Inspection Procedure for Belt Tension.”...
-
Page 12: Sound Test
SOUND AND VIBRATION STATMENT... - Page 13 This page left black intentionally...
- Page 14 Technical assistance: For technical assistance please contact your Local Dealer.