hit counter script
Husqvarna 3002 Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. 3002
  6. Owner's manual
Husqvarna 3002 Owner's Manual

Husqvarna 3002 Owner's Manual

Tractors/ride mowers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
03002
LGT2554
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 3002

Summary of Contents for Husqvarna 3002

  • Page 1 03002 LGT2554 Owner's Manual...

  • Page 2: Safety Rules

    Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent ac- ci den tal starting when setting up, trans port ing, ad just ing or making repairs, al ways dis con nect spark plug...
  • Page 3 Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the ma chine and the mowing activity. Never assume that children will remain where you last saw them. •...

  • Page 4: Table Of Contents

    Gasoline Capacity 4 Gallons and type: Unleaded Regular Oil Type (API-SG-SL): SAE 30 (above 32°F) SAE 5W-30 (below 32°F) Oil Capacity: W/ Filter: Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: Reverse: Charging System: 15 AMPS @ 3600 RPM Battery: AMP/HR: MIN.

  • Page 5: Assembly

    UNASSEMBLED PARTS Mower (5) Large Retainer Springs - 7/16 (2) Smaller Retainer Springs - 5/16 (1) Anti-Sway Bar (2) Rear Lift Link Assemblies Your new tractor has been assembled at the factory with ex- ception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier.
  • Page 6 TO ADJUST SEAT (See Fig. 2): • Grasp adjustment handle(A) and pull up, slide seat to desired po si tion and release adjustment handle. Fig. 2 NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al.
  • Page 7 • Pivot bar towards you and insert other end of bar into hole in rear mower bracket (D). Move mower as needed to insert bar. • Secure with washer and retainer spring as shown Fig. 7 • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with washer and retainer spring.
  • Page 8 • Turn steering wheel to position wheels straight forward. • ATTACH FRONT LINK (E) - Work from left side of trac- tor. Insert rod end of link assembly through front hole in tractor front suspension bracket (F) and secure with retainer spring (G) through hole in link located behind the bracket.

  • Page 9: Operation

    These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. REVERSE NEUTRAL REVERSE ENGINE OFF OPERATION SYSTEM (ROS) LIGHTS ON BATTERY FUEL ATTACHMENT ATTACHMENT CLUTCH DISENGAGED CLUTCH ENGAGED FREE WHEEL (Automatic Models only) Failure to follow instructions could result in serious injury or death.
  • Page 10 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your trac tor.
  • Page 11 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles.
  • Page 12 TO MOVE FORWARD AND BACKWARD (See Fig. 17) The direction and speed of movement is controlled by the motion control lever. (J) Fig. 17 • Start tractor with motion control le ver in neutral position. • Release parking brake. • Slowly move motion control lever to desired position.
  • Page 13 TO TRANSPORT (See Fig. 13 and 21) When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in free wheel ing po si tion. Free wheel control is located at the rear drawbar of tractor. •...

  • Page 14: Before Starting The Engine

    BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped, from the factory, already filled with sum mer weight oil. • Check engine oil with tractor on level ground. • Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level.

  • Page 15: Operation

    PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. To ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel- oped during shipping of your tractor.

  • Page 16: Maintenance Schedule

    MAINTENANCE SCHEDULE Check Brake Operation Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) Change Engine Oil (without oil filter) Clean Air Filter...

  • Page 17: Maintenance

    TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE”...
  • Page 18 DECK WASHOUT PORT (See Fig. 26) Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.

  • Page 19: Clean Air Screen

    TO CHANGE ENGINE OIL (See Fig. 27) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. •...

  • Page 20: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. •...
  • Page 21 SERVICE AND ADJUSTMENTS NOTE: Each full turn of adjustment nut will change mower height about 3/16". • Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results. PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig.

  • Page 22: To Replace Mower Blade Drive Belt

    SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 34) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. En gage parking brake. • Lower attachment lift lever to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). CAUTION: Belt tension rod is spring loaded.
  • Page 23 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL (See Fig. 36) • Block up axle securely. • Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. •...

  • Page 24: Interlocks And Relays

    SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 39) WARNING: Do not short battery ter mi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from ac ci den tal grounding.

  • Page 25: Storage

    Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark.

  • Page 26: Trou Ble Shoot Ing

    TROUBLESHOOTING POINTS PROBLEM CAUSE 1. Out of fuel. Will not start 2. Engine not “CHOKED” properly. 3. Engine flooded. 4. Bad spark plug. 5. Dirty air filter. 6. Dirty fuel filter. 7. Water in fuel. 8. Loose or damaged wiring. 9.

  • Page 27: Trou Ble Shoot Ing

    TROUBLESHOOTING POINTS PROBLEM CAUSE Engine continues 1. Faulty operator-safety presence control system. to run when oper- ator leaves seat with attachment clutch engaged 1. Worn, bent or loose blade. Poor cut - uneven 2. Mower deck not level. 3. Buildup of grass, leaves, trash under mower. 4.

  • Page 28: Repair Parts

    DECALS PART DESCRIPTION 532 41 91-38 Decal, Warning 532 42 38-30 Decal, Ethanol E85 532 42 41-02 Decal, Warning Spark Arrestor 532 19 15-54 Decal, Hood Cust Resp 532 17 84-55 Decal, Caution 532 19 87-85 Decal, Mower Sch. 532 14 50-05 Decal, Battery Dnge/Poi WHEELS AND TIRES wheel_art_1-tex...
  • Page 29 SCHEMATIC SCH12 PTO SWITCH (MATING SIDE) IGNITION SWITCH POSITION CIRCUIT “MAKE” M+G+A1 B+A1 RUN/OVERRIDE B+A1 L+A2 START B + S + A1 BATTERY FUSE AMMETER (OPTIONAL) WHITE PTO SWITCH (DISENGAGED) WHITE BLACK BLACK BLACK BLACK BLACK IGNITION UNIT (OPTIONAL) HOUR BLUE METER FUEL...
  • Page 30 TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 ELECTRICAL T07S With 12V Outlet Option With Service Minder Option...
  • Page 31 ELECTRICAL PART DESCRIPTION 532 16 34-65 Battery 874 76 04-12 Bolt Hex Hd 1/4-20 unc x 3/4 532 41 41-25 Battery Asm. Tray 532 17 61-38 Switch Interlock 532 18 37-59 Harness Socket Light 532 00 41-52 Bulb, Light #1156 532 40 02-53 Cable Battery 532 41 28-95...
  • Page 32 TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 CHASSIS chassis-tex_TEX GT HUSQ_55_r1...
  • Page 33 CHASSIS PART DESCRIPTION 532 40 87-01 Dash 532 41 10-46 Hood Asm. 532 19 89-07 Lens LH 532 40 86-07 Grille Asm. 532 19 89-06 Lens RH 532 19 61-25 Plate Engine 817 06 05-12 Screw 5/16-18 x 3/4 532 40 18-25 Fender 873 68 05-00 Nut Crown Lock 5/16-18...
  • Page 34 DRIVE drive-tex_K46_fender_6...
  • Page 35 DRIVE PART DESCRIPTION - - - - - - - - - Transaxle, TUFFTORQ K46 AW 532 18 62-11 532 19 98-44 Hub Asm. Wheel Rear 22" TX GT .06 532 14 00-80 Bolt Hub Wheel Rear 819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.
  • Page 36 ENGINE 21 20 SPARK ARRESTER KIT Engine-tex_Kohl-2cyl_1_r2 PART DESCRIPTION - - - - - - Engine Kohl Model No. SV730 532 14 97-23 Muffler 532 19 43-20 Keeper Belt Engine 532 17 93-35 Clutch Electric 532 19 43-43 Pulley Engine 532 41 41-52 Tank Fuel 532 42 06-35...

  • Page 37: Seat Assembly

    SEAT ASSEMBLY seat-tex_6.5SL_3 PART DESCRIPTION 532 40 66-21 Seat 532 18 01-66 Bracket Pivot Fender 532 14 06-75 Strap, Asm Fender 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc 532 12 41-81 Spring, Seat Cprsn 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems 532 19 69-77 Pan, Seat 532 17 18-52...
  • Page 38 TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17 STEERING ASSEMBLY steering-tex_special_26...

  • Page 39: Steering Assembly

    STEERING ASSEMBLY PART DESCRIPTION 532 42 34-69 Wheel, Steering 532 19 59-68 Axle Asm., Front 532 40 30-89 Spindle Asm., LH 532 40 30-90 Spindle Asm., RH 532 12 49-31 Bearing, Race Thrust Harden 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga. 812 00 00-29 Ring, Clip #T5304-75 532 12 12-32...

  • Page 40: Mower Deck

    MOWER DECK mower_deck 54-tex_16...
  • Page 41 MOWER DECK PART DESCRIPTION 532 40 31-25 Deck Weldment Mower 532 19 60-66 Cover Mandrel LH 532 19 71-81 Cover Mandrel RH 532 19 30-03 Bolt 7/16 Asm. Blade 532 18 72-56 Blade Bagging 532 18 72-55 Blade Mulching 532 40 48-51 Rod Anti Sway 532 18 72-91 Shaft Asm.

  • Page 42: Mower Lift

    MOWER LIFT lift-tex_3 PART DESCRIPTION 532 19 52-23 Shaft Asm., Lift 532 19 52-30 Lever Asm., Lift RH 532 41 15-55 Grip, Lever 532 19 63-14 Spring Torsion 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock 532 19 53-04 Spring Lift Assist 819 19 19-12 Washer Clear Zinc...
  • Page 44 532 42 57-55 Rev.1 04.20.09 SR Printed in the U.S.A.

This manual is also suitable for:

532 42 57-5596045001700Lgt2554

Table of Contents