To Replace Motion Drive Belt - Husqvarna YTH2242 Owner's Manual
Husqvarna lawn tractor owner's manual
Hide thumbs
Also See for YTH2242:
- Owner's manual (44 pages) ,
- Owner's manual (44 pages) ,
- Owner's manual (44 pages)
Table of Contents
Advertisement
SERVICE AND ADJUSTMENTS
TO CHECK AND ADJUST BRAKE
(See Fig. 24)
Your tractor is equipped with an ad just able brake system
which is mounted on the right side of the transaxle.
If tractor requires more than fi ve (5) feet to stop at highest
speed in high est gear on a level, dry concrete or paved
surface, then brake must be checked and ad just ed.
TO CHECK BRAKE
•
Park tractor on a level, dry concrete or paved surface,
depress clutch/brake pedal all the way down and en-
gage parking brake.
•
Disengage transmission by placing freewhel control
in "transmission disengaged" position. Pull freewheel
con trol out and into the slot and release so it is held in
the disengaged position.
The rear wheels must lock and skid when you try to manually
push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to be replaced.
TO ADJUST BRAKE
•
Depress clutch/brake pedal all the way down and en-
gage parking brake.
•
Measure distance between brake operating arm and
nut "A" on brake rod.
•
If distance is other than 1-9/16", loosen jam nut and
turn nut "A" until distance becomes 1-9/16". Retighten
jam nut against nut "A".
•
Engage transmission by placing freewheel control in
"trans mis sion engaged" position.
•
Road test tractor for proper stopping distance as stated
above. Readjust if nec es sary. If stopping distance is
still greater than fi ve (5) feet in high est gear, further
main te nance is nec es sary. Replace brake pads or
contact a qualifi ed service center.
WITH PARKING BRAKE "ENGAGED"
1-9/16"
DO NOT TOUCH THIS NUT. IF FURTHER
BRAKE AD JUST MENT IS NECESSARY CON-
TACT YOUR NEAREST AUTHORIZED SERVICE
CENTER/DEPARTMENT
TO REPLACE MOTION DRIVE BELT
(See Fig. 25)
Park the tractor on level surface. En gage parking brake.
For as sis tance, there is a belt installation guide decal on
bottom side of left footrest.
NUT "A"
JAM NUT
OPERATING
ARM
FIG. 24
BELT REMOVAL -
•
Remove mower (See "TO RE MOVE MOWER" in this
section of manual).
NOTE: Observe entire motion drive belt and position of all
belt guides and keepers.
•
Disconnect clutch wire harness.
•
Remove clutch locator.
•
Remove belt from stationary idler and clutching idler.
•
Remove belt downward from engine pulley and around
electric clutch.
•
Pull belt slack toward rear of trac tor. Carefully remove
belt up wards from trans mis sion input pulley and over
cooling fan blades.
•
Remove belt from center span keeper and pull belt
away from tractor.
BELT INSTALLATION -
•
Carefully work new belt down around transmission
cool ing fan and onto the input pulley.
•
Slide belt into the center span keeper.
•
Pull belt toward front of tractor and roll belt around
electric clutch and onto engine pulley.
•
Install belt through stationary idler and clutch ing
idler.
•
Reinstall clutch locator and tighten nut securely.
•
Reconnect clutch harness.
•
Make sure belt is in all pulley grooves and in side all
belt guides and keep ers.
•
Install mower (See "TO IN STALL MOWER" in this sec-
tion of manual).
ELECTRIC
CLUTCH
CLUTCH ING
IDLER
STATIONARY
IDLER
CENTER SPAN
KEEPER
TRANS MIS SION
INPUT PULLEY
TRANSMISSION REMOVAL/REPLACEMENT
Should your transmission require removal for service or
replacement, it should be purged after reinstallation and
before operating the tractor. See "PURGE TRANS MIS SION"
in the Operation section of this manual.
TRANSAXLE
NEUTRAL ADJUSTMENT(See Fig. 26)
The motion control lever has been pre set at the factory and
adjustment should not be necessary.
•
Loosen adjustment bolt in front of the right rear wheel,
and lightly tighten.
21
CLUTCH LOCATOR
CLUTCH
WIRE HAR NESS
FIG. 25
MOTION CONTROL LE VER
Hide quick links:
Advertisement
Table of Contents
