hit counter script
Husqvarna 1330SBEXP Owner's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Snow Blower
  5. 1330SBEXP
  6. Owner's manual

Husqvarna 1330SBEXP Owner's Manual

Husqvarna snow blower owner's manual
Hide thumbs Also See for 1330SBEXP:
Table of Contents

Advertisement

Quick Links

1330SBEXP
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 1330SBEXP

Summary of Contents for Husqvarna 1330SBEXP

  • Page 1 1330SBEXP Owner's Manual...

  • Page 2: Safety Rules

    Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. Look for this symbol to point out im- por tant safety precautions.

  • Page 3: Table Of Contents

    6. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the en- gine.
  • Page 4 PARTS PACKED SEPARATELY IN CARTON...

  • Page 5: Assembly / Pre-Operation

    ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product. Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes.
  • Page 6 ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into eye of cable with loop opening down as shown.
  • Page 7 ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

  • Page 8: Operation

    OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product.
  • Page 9 SPARK PLUG SAFETY IGNITION CHOKE CON- TROL THROTTLE / ENGINE CONTROL RECOIL POWER (AUXILIARY) CORD STARTER PLUG ELECTRIC HANDLE START BUTTON PRIM ER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.
  • Page 10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs.
  • Page 11 AUGER CONTROL LEVER FIG. 15 USING THE CLEAN-OUT TOOL (See Fig. 16) In certain snow conditions, the discharge chute may be- come clogged with ice and snow. Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or in spect ing, make certain all controls are disengaged and the auger/impeller and all moving parts have stopped.

  • Page 12: Before Starting The Engine

    NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property dam age or damage to the snow thrower.
  • Page 13 damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied be fore stor age of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty.

  • Page 14: Maintenance

    • Slightly overlap each successive path to ensure all snow will be removed. • Throw snow downwind whenever possible. • Ad just the skid plates to proper height for current snow con di tions. See “TO ADJUST SKID PLATES” in this section of this manual.

  • Page 15: Snow Thrower

    SNOW THROWER Always observe safety rules when performing main te nance. TIRES • Maintain proper air pressure in both tires (14–17 P.S.I. / 19-24.5 N-m). • Keep tires free of gasoline / oil, which can harm rubber. NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer.

  • Page 16: Service And Adjustments

    SERVICE AND ADJUSTMENTS WARNING: To avoid serious injury, before performing any service or ad- just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4.

  • Page 17: To Replace Belts

    SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 24) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualifi...

  • Page 18: Storage

    TO REMOVE WHEELS (See Fig. 25) • Remove the klik pin and remove wheel from axle. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

  • Page 19: Troubleshooting

    TROUBLESHOOTING See appropriate section in manual unless directed to a qualifi ed service center. PROBLEM CAUSE Does not start 1. Fuel shut-off valve (if so equipped) in OFF position. 2. Safety ignition key is not inserted. 3. Out of fuel. 4.

  • Page 20: Repair Parts

    REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19...

  • Page 21: Key Part No

    REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 KEY PART DESCRIPTION 532 18 86-63 Bar, Weight 532 75 11-53 Nut, Hex 5/16-18 872 11 05-10 Bolt, Carriage 5/16-18 x 1-1/4 532 19 10-79 Pulley, Impeller...
  • Page 22 REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19...
  • Page 23 REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 KEY PART NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
  • Page 24 REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19...

  • Page 25: 874 78 05-24 Screw, Hex Head 5/16-18

    REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 KEY PART NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
  • Page 26 REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 DRIVE...

  • Page 27: 532 19 85-80 Screw, Hex Head 1/4-28

    REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 KEY PART NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.
  • Page 28 REPAIR PARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19...
  • Page 29 REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 KEY PART 532 19 28-73 Spring, Traction Idler 532 18 05-22 Pulley, Idler (2-1/4) - - - 874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4...
  • Page 30 REPAIR PARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19...

  • Page 31: 817 00 06-16 Screw, Hex Head

    REPAIR PARTS SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19 KEY PART KEY PART NOTE: All component dimensions given in U.S. inches. IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

  • Page 32: Warranty

    532 40 57-43 Rev. 3 08.23.06 BY Printed in U.S.A.

This manual is also suitable for:

96193001900

Table of Contents