Advertisement
Available languages
Available languages
DEH-P6950IB
This product conforms to new cord colors.
Los colores de los cables de este producto se
conforman con un nuevo código de colores.
As cores dos fios deste produto seguem um novo
padrão de cores.
Æ...b¹b'« „öÝô« Ê«
uë lÄ "UN'« «c¼ r− M¹
Printed in Thailand
<XRD7146-A/N> ES
<KMMNX> <06J00000>
Installation
Note:
1. Insert the mounting sleeve into the dashboard.
•
Check all connections and systems before final
•
When installing in a shallow space, use a sup-
installation.
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
•
Do not use unauthorized parts. The use of
mounting sleeve.
unauthorized parts may cause malfunctions.
2. Secure the mounting sleeve by using a screwdriv-
•
Consult with your dealer if installation requires
er to bend the metal tabs (90°) into place.
drilling of holes or other modifications of the
vehicle.
3. Install the unit as illustrated.
•
Do not install this unit where:
Removing the Unit
— it may interfere with operation of the vehicle.
1. Extend top and bottom of the trim ring outwards
— it may cause injury to a passenger as a result
to remove the trim ring. When reattaching the
of a sudden stop.
trim ring, push the trim ring onto the unit until it
•
The semiconductor laser will be damaged if it
clicks. (If the trim ring is attached upside down,
overheats. Install this unit away from hot places
the trim ring will not fit properly.)
such as near the heater outlet.
•
It becomes easy to remove the trim ring if the
•
Optimum performance is obtained when the unit
front panel is released.
is installed at an angle of less than 60°.
Trim ring
60°
•
When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
2. Insert the supplied extraction keys into both sides
space behind the rear panel and wrap any loose
of the unit until they click into place.
cables so they are not blocking the vents.
3. Pull the unit out of the dashboard.
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.
DIN Front-mount
Installation with the rubber bush
Mounting sleeve
Dashboard
182
1 1 1 82
53
53
Rubber bush
Screw
ENGLISH
DIN Rear-mount
1. Extend top and bottom of the trim ring outwards
to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)
•
It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Determine the appropriate position where the
holes on the bracket and the side of the unit
match.
3. Tighten two screws on each side.
Use either truss screws (5 mm × 8 mm) or
•
flush surface screws (5 mm × 9 mm), depend-
ing on the shape of screw holes in the
bracket.
Screw
Dashboard or Console
Factory radio mounting bracket
Advertisement
Table of Contents
Related Manuals for Pioneer DEH-P6950IB
Summary of Contents for Pioneer DEH-P6950IB
- Page 1 (If the trim ring is attached upside down, overheats. Install this unit away from hot places the trim ring will not fit properly.) DEH-P6950IB such as near the heater outlet. • It becomes easy to remove the trim ring if the •...
-
Page 2: Instalación
Instalación ESPAÑOL Instalação PORTUGUÊS (B) Nota: 1. Inserte el manguito de montaje en el tablero de Montaje trasero DIN Nota: 1. Insira a manga de montagem no painel de instru- Montagem traseira DIN instrumentos. mentos. • Verifique todas las conexiones y sistemas antes •... - Page 3 WOÐdFë VOÂd²Ã« ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ fO¹UIÄ V Š wÄUÄ_« VOÂd²Ã« fO¹UIÄ V Š wHKš VOÂdð • WOÞ UD*« W³K'« lÄ VOÂd²Ã« • VO d²Ã« »« dł • «œ«bFë WŠ uà 1 1 1 82 • • — WOÞUDÄ W³Kł —...
-
Page 4: Connection Scheme
1. iPod with Dock 3. Dock connector port 1. iPod with Dock 3. Dock connector port Connector Connector 4. Interface cable (e.g., CD-I200) 4. Interface cable (e.g., CD-I200) 17. Power amp (sold separately) (sold separately) (sold separately) 2. Dock connector 2. -
Page 5: Connecting The Units
Connecting the Units Conexión de las unidades ENGLISH ESPAÑOL Note: • Control signal is output through blue/white cable Connection Diagram 26. Left Nota: • La señal de control se emite a través del cable Diagrama de conexión 23. Azul/blanco • When this unit is installed in a vehicle without when this unit is powered on. -
Page 6: Conexão Dos Componentes
Conexão dos componentes PORTUGUÊS (B) Nota: • O sinal de controle é emitido através do cabo Diagrama de conexão 24. Controle remoto de sistema • Quando este aparelho é instalado em um veículo azul/branco quando este aparelho é ligado. 25. Alto-falante frontal Conecte-o a um terminal de controle remoto de sem posição ACC (acessório) no interruptor de 26. - Page 7 WOÐdFë «bŠuë qO uð • ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ qO u²Ã« jD Ä • öB²Ä WOHK)« WŽUL ë pKÝ ÊuJ¹ ô UÄbMŽ ©± qJAë® WOŽd iH MÄ u WŽUL Ð ÊËbÐ WOŽd iH MÄ u WŽULÝ Â«b ²Ý« bMŽ ©≤...