Toshiba E-Studio 2330c Troubleshooting Manual page 11
Multifunctional digital color systems
Hide thumbs
Also See for E-Studio 2330c:
- Imaging manual (262 pages) ,
- Printing manual (178 pages) ,
- Quick start manual (78 pages)
Table of Contents
Advertisement
Message
READY (INNER TRAY FULL)
Add paper
Call for service
Examine stapler in the Saddle Stitch
unit
Check staple cartridge in the Saddle
Stitch unit
Check staple cartridge
Examine Stapler
Time for Slit glass and Main charger
cleaning
Saving energy Press START button
CHANGE DRAWER TO CORRECT
PAPER SIZE
Time for periodic maintenance
POWER FAILURE
ERASING DATA
Check paper size setting on control
panel for Bypass
Set the paper on the bypass tray
again.
Reboot the machine
Problem Description
The receiving tray of the equipment is
full of paper.
No paper is left in a drawer or on the
bypass tray.
The equipment requires adjusting by
a service technician.
Staple jam has occurred in the stapler
of the Saddle Stitch unit.
No staples are left in the stapler of the
Saddle Stitch unit.
No staples are left in the stapler of the
Finisher.
Staple jam has occurred in the stapler
of the Finisher.
The slit glass and the main charger
need cleaning.
The equipment is in the Energy Saver
mode after a period of time.
No paper suitable for the original is
set.
The equipment requires inspection
and maintenance by a service
technician.
A job was interrupted by a power
failure or some other reasons.
The Data Overwrite Enabler is
clearing the data.
Paper jam has occurred because of a
mismatch between the paper size
placed in the bypass tray and the size
registered for the bypass tray in the
equipment.
The paper placed on the bypass tray
jammed.
An error has occurred in the
equipment and it stopped normal
operation.
1 TROUBLESHOOTING FOR THE HARDWARE
Corrective Action
Remove the paper from the receiving tray of the
equipment.
Set paper in the drawer or on the bypass tray. The
touch panel indicates which drawer (or the bypass
tray) has no paper.
To set paper, refer to the Copying Guide.
Contact your service representative with the error
code displayed on the right side of the touch panel.
Never attempt to repair, disassemble or modify the
equipment by yourself.
You could cause a fire or get an electric shock.
Always contact your service representative for
maintenance or repair of the internal parts of the
equipment.
Remove the jammed staples.
P.43 "Staple jam in the Saddle Stitch unit"
Refill the staples.
P.54 "Refilling With Staples"
Refill the staples.
P.54 "Refilling With Staples"
Remove the jammed staples.
P.38 "Clearing a Staple Jam"
Clean the slit glass and the main charger.
P.62 "Cleaning the slit glasses"
P.64 "Cleaning the main chargers"
Press the [START] button to clear the Energy Saver
mode.
Place the suitable size paper for the original in the
drawer.
Contact your service representative.
The print or fax job may be incomplete. Press [JOB
STATUS] to check whether any jobs are unfinished.
To clear the messages, press the [RESET] button
twice.
This message is displayed if the Data Overwrite
Enabler (optional) is installed. You can operate the
equipment while the message is displayed.
Register the paper size correctly. Just releasing the
paper jam does not prevent another paper jam.
P.31 "Clearing a paper jam caused by a wrong
paper size setting"
Remove the jammed paper and set the paper again.
Rebooting the equipment may correct the error. To
reboot the equipment, turn the main power switch off
and then on.
Messages Displayed on the Touch Panel
9
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
