Summary of Contents for Vacon DPD00109
- Page 1 Keypad Remote Control Options Installation Manual DPD00109 Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com...
- Page 2 Keypad Remote Control Options vacon Installing Keypad Remote Control Options Introduction Remote control options allow the keypad functionality of the X4 and X5 AC drives to be used remotely from the controller itself. The options provide a NEMA 4X / IP66 rating for the keypad in a remote location. Products covered by this instruction manual include XRKPM, XRKWM, and XRKMK.
-
Page 3: Sensitive Equipment
Keypad Remote Control Options WARNING SENSITIVE EQUIPMENT The keypad contains static-sensitive components. It should be handled only by a static-safe installer, using a grounded wrist strap. Failure to observe this precaution may cause premature equipment failure. DANGER HAZARDOUS VOLTAGE •... - Page 4 Keypad Remote Control Options vacon Figure 1: Dimensions of Remote Keypad Kit Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com...
- Page 5 Keypad Remote Control Options Step 2. AC Drive Preparation (XRKPM, XRKWM) Note: For drive sizes 3 and larger (XRKMK), skip to step 9, beginning on page 13, and proceed through Step 12. 1. Note the warnings and cautions on the unit and in the user’s manual.
- Page 6 Keypad Remote Control Options vacon Step 3. Preparing the Keypad Interface Module (KIM) (XRKPM only) 1. There are two housings supplied with the kit; only one will fit your AC drive properly. Select the keypad module housing that physically matches the one you removed in Step 2.
- Page 7 Keypad Remote Control Options Step 4. Re-assembling the AC Drive (XRKPM only) 1. Plug the Keypad Interface Module (KIM) fabricated in Step 3 into the inverter, as it was originally (see Step 2, #4). 2. Fasten the KIM with the two (2) M4 x 10 screws removed in Step 2, limiting torque to 12 in-lb.
- Page 8 Keypad Remote Control Options vacon Step 5. Installing the Remote Keypad Assembly into the Host Enclosure (XRKPM only) 1. Position the remote keypad assembly into the enclosure prepared in Step 1 (page 2. Fasten the keypad module with the four (4) M5 x 12 screws provided, limiting torque to 26 in-lb maximum.
- Page 9 Keypad Remote Control Options Step 6. Preparing the Keypad Interface Module (KIM) (XRKWM only) (Note: You will need to provide a 15-conductor cable for this step.) 1. There are two housings supplied with the kit; only one will fit your AC drive properly. Select the keypad module...
- Page 10 Keypad Remote Control Options vacon Step 7. Re-assembling the AC Drive (XRKWM only) 1. Plug the Keypad Interface Module (KIM) fabricated in the previous step into the inverter, as it was originally (see Step 2, #4). 2. Fasten the KIM with the two (2) M4 x 10 screws removed in Step 2, limiting torque to 12 in-lb.
- Page 11 Keypad Remote Control Options Step 8. Installing the Remote Keypad Assembly into the Host Enclosure (XRKWM only) 1. Position the remote keypad assembly into the enclosure prepared in Step 1 (page 2. Fasten the keypad module with the four (4) M5 x 12 screws provided, limiting torque to 26 in-lb maximum.
- Page 12 Keypad Remote Control Options vacon Step 9. AC Drive Preparation (XRKMK only) 1. Note the warnings and cautions on the unit and in the user’s manual. 2. Loosen the cover screws from the AC drive and open the cover. 3. Remove the four (4) screws that secure the keypad assembly and retain these for future use. These are M5 x 12 screws.
- Page 13 Keypad Remote Control Options Step 10. Installing the Keypad Interface Module (KIM) into the AC Drive (XRKMK only) 1. Position the keypad interface module (KIM) into the door opening. 2. Fasten the keypad module with the four (4) M5 x 12 screws provided, limiting torque to 26 in-lb maximum.
- Page 14 Keypad Remote Control Options vacon Step 11. Assembling the Remote Keypad Interface (XRKMK only) 1. Insert the connector stacker into the receptacle on the remote keypad assembly (removed in Step 9) as shown Figure 11 below. 2. Insert the keypad interface board onto the rear of the keypad assembly, being sure to engage the connector stacker simultaneously.
- Page 15 Keypad Remote Control Options Step 12. Installing the Remote Keypad Assembly into the Host Enclosure (XRKMK only) 1. Position the remote keypad assembly into the enclosure prepared in Step 1 (page 4). 2. Fasten the keypad module with the four (4) M5 x 12 screws provided, limiting torque to 26 in-lb maximum.