Page 1 DCR-TRV110E/TRV210E/TRV310E East European Model Photo: DCR-TRV310E North European Model Russian Model B800 MECHANISM DCR-TRV110E Taiwan Model DCR-TRV310 NTSC MODEL : DCR-TRV103/TRV110/TRV110P/TRV203/TRV210/ For MECHANISM ADJUSTMENT, refer to TRV310/TRV310P/TRV315/TR7000 the “8mm Video MECHANICAL PAL MODEL : DCR-TRV110E/TRV210E/TRV310E/TR7000E/TR7100E ADJUSTMENT MANUAL ” (9-973-801-11). SPECIFICATIONS...
Page 2 DCR-TRV103/TRV110/TRV110E: E, Viewfinder AC power adaptor HK, AUS, CN, JE/TRV110P/TRV203/ DCR-TRV110E/TRV203/TRV210/ TRV210/TRV210E: CN/TRV310/ TRV210E/TRV310/TRV310E/ Power requirements TRV310E: E, HK, AUS, CN, JE/ TRV310P: 3.2 W 100 - 240 V AC, 50/60 Hz DCR-TRV103/TRV110/TRV110P/ TRV310P/TRV315/TR7000: Power consumption DV input/output TRV315: 3.1 W...
Page 3 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 4 — 4 —...
Page 5 TABLE OF CONTENTS SERVICE NOTE 2-3. F Panel Assembly, Cabinet (R) Assembly ······················· 2-4 2-4. MA-354, 355, 357 Board ················································ 2-4 POWER SUPPLY DURING REPAIRS ····························· 8 2-5. Mechanism Deck ····························································· 2-5 TO TAKE OUT A CASSETTE WHEN NOT EJECT 2-6.
Page 6: Monochrome Electronic Viewfinder System Adjustments
White Balance Adjustment (VF-126 board) ·················· 5-34 • PD-105, 106 (RGB Decoder, LCD)(2/2) 1-5. Monochrome Electronic Viewfinder System Adjustments Schematic Diagram ····································· 4-114 (DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/ • VF-129 (B/W EVF) TRV210/TRV210E/TRV310/TRV310E/TRV310P) ······ 5-35 Printed Wiring Board (B/W EVF Model) ... 4-117 1-5-1. Horizontal Slant Check ················································· 5-35 •...
Page 7: Repair Parts List
Recording of the tape path check signal ························ 5-44 Digital8 Playback Level Check ····································· 5-69 Tape path check ····························································· 5-44 Overall Level Characteristics Check ····························· 5-69 5-3. VIDEO SECTION ADJUSTMENT ······························ 5-45 Overall Distortion Check ··············································· 5-69 3-1. Preparations Before Adjustments ·································· 5-45 Overall Noise level Check ·············································...
Page 8: Service Note
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the Battery switch battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this.
Page 9: Service Mode Display
SELF-DIAGNOSIS FUNCTION Self-diagnosis Function Self-diagnosis Display When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or Display viewfinder or Display window shows a 4-digit display consisting window what to do.
Page 10 Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 11 Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Inspect the lens block focus reset sensor (Pin !™ of CN551 of VC- 213 board) when focusing is performed when the control dial is Difficult to adjust focus rotated in the focus manual mode and the focus motor drive circuit (Cannot initialize focus.) (IC551 of VC-213 board) when the focusing is not performed.
Page 12 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E SECTION 1 This section is extracted from instruction manual. (3-865-973-11) GENERAL...
Page 21 1-10...
Page 22 1-11...
Page 23 1-12...
Page 24 1-13...
Page 25 1-14...
Page 26 1-15...
Page 27 1-16...
Page 28 1-17...
Page 29 1-18...
Page 30 1-19...
Page 31 1-20E...
Page 32 MECHANISM DECK, VC-213, DD-117, VC-213, DD-117, PJ-95, 96, 98 PJ-95, 96, 98 boards boards check service position : DCR-TR7000/TR7000E/TR7100E TR MODEL : DCR-TRV103/TRV110/TRV110E/TRV110P 2.5 INCH LCD MODEL : DCR-TRV203/TRV210/TRV210E/TRV315 3.0 INCH LCD MODEL : DCR-TRV310/TRV310E/TRV310P 3.5 INCH LCD MODEL : DCR-TRV103/TRV110/TRV110E/TRV110P...
Page 33 NOTE: Follow the disassembly procedure in the numerical order given. 2-1. 2.5 INCH LCD UNIT, PD-105 BOARD 7 P cabinet (C)(952) assembly 8 Two tapping screws (B2 × 8) 6 Claws 4 Two screws (M2 × 4), lock ace, p2 3 Rotate it by 90 °...
Page 34 2-2. 3.0/3.5 INCH LCD UNIT, PD-106 BOARD 7 P cabinet (C)(955) 3 Rotate it by 90 ° 8 Two tapping screws assembly in the direction (B2 × 8) 6 Claws of the arrow. 4 Screw (M2 × 4), lock ace, p2 Indication LCD block assembly Hinge...
Page 35 2-3. F PANEL ASSEMBLY, CABINET (R) ASSEMBLY !£ Screw (M2 × 4), lock ace, p2 2 Remove the claw 8 FP-77 flexible board (22P) !º Cushion (N) - 2 1 1 Two screws (M2 × 4), Note lock ace, p2 6 Screw (M2 ×...
Page 36: Mechanism Deck
2-5. MECHANISM DECK Remove it in the direction Remove it in the direction of the arrow a . 2 Cassette lid assembly of the arrow b . Remove it gently as a thin flexible 1 Two screws (M2 × 3), board is held by a claw.
Page 37: Evf Block Assembly
2-6. EVF BLOCK ASSEMBLY < 2.5 INCH LCD MODEL > < TR MODEL > 6 B/W EVF block assembly 5 Color EVF block assembly 3 FFC-256 2 FP-47 flexible board (20P) flexible flat cable (4P) 5 Remove 4 Remove the claws the claws 3 Three tapping 4 Three tapping...
Page 38 2-7. VF-129 BOARD (B/W EVF MODEL) 4 Finder (S) assembly 3 Rotate it in the direction of the arrow b and remove it in the direction of the arrow c . 1 Screw !º 2 Slide the button in the direction of the arrow a .
Page 39 2-8. VF-126 BOARD (COLOR EVF MODEL) !§ EVF cabinet (upper C) (95) 9 FP-47 flexible board !∞ Two tapping 4 Remove the slide fixed base (C) screws (B2 × 5) !¡ by sliding it in the arrow direction Claws 8 Remove the claw !•...
Page 40: Lens Block
2-9. LENS BLOCK !º Flexible board (from LENS block) (24P) 7 Screw (M2 × 3) 4 FP-54 flexible board (16P) 6 Screw (M2 × 3) !¡ LENS block - 2 1 a r d 1 FFC-236 flexible flat cable (50P) 9 Ferrite bead 8 FP-45 flexible board (8P) 5 Screw (M2 ×...
Page 41 2-10.MECHANISM DECK, VC-213, DD-117, PJ-95, 96, 98 BOARDS 3 Screw (M2 × 4), !™ Cabinet (R) assembly Remove it in the direction lock ace, p2 of the arrow a . Remove it in the direction of the arrow b . Remove it gently as a thin !¡...
Page 42 [MECHANISM DECK, VC-213, DD-117, PJ-95, 96, 98 BOARDS CHECK SERVICE POSITION] Battery panel (P) AC IN assembly Control switch block (SS-8500) AC POWER ADAPTOR Base 2 Adjustment remote DC IN commander (RM-95) Base 1-3 (Use box or the like) DD-117 board Extension cable (J-6082-439-A) (70P) Control switch...
Page 43 2-11.CF-65 BOARD (TR MODEL) 1 FP-62 flexible board (8P) 2 FP-47 flexible board (20P) !¡ Indication LCD block assembly 9 CF-65 board Remove it in the directin of the arrow. 7 Four tapping screws (B2 × 5) 8 FP-94 flexible board (26P) !º...
Page 44 2-14.CIRCUIT BOARDS LOCATION NOTE: For the difference of the printed wiring boards due to needs and destinations, refer to “Table for differences of function” on page 4. DD-117 (DC/DC CONVERTER) VF-126 (COLOR EVF) CD-212, 213 (CCD IMAGER) MA-354, 355, 357 STEREO MIC AMP, LASER LINK PJ-95, 96, 98...
Page 45 2-15.FLEXIBLE BOARDS LOCATION FP-49 CONTROL SWITCH BLOCK (FK-8500) FP-54 FP-45 (From S/T REEL SENSOR) (From CAPSTAN MOTOR) (From DRUM MOTOR) FP-77 (From VIDEO HEAD) (From LENS BLOCK) FP-78 From LOADING MOTOR, MODE SWITCH CONTROL SWITCH BLOCK (SS-8500) FP-47 (USED COLOR EVF) FFC-256 (USED B/W EVF) FP-642 FP-62...
Page 46 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ SECTION 3 TRV210E/TRV310/TRV310E/TRV310P/TRV315 BLOCK DIAGRAMS DCR-TR7000/TR7000E/TR7100E 3-1. OVERALL BLOCK DIAGRAM (1)
Page 47 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E 3-2. OVERALL BLOCK DIAGRAM (2)
Page 48 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E 3-3. POWER BLOCK DIAGRAM (1) 3-10...
Page 49 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E 3-4. POWER BLOCK DIAGRAM (2) 3-13 3-14 3-15 3-16E...
Page 50 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ SECTION 4 TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E 4-1. FRAME SCHEMATIC DIAGRAM-1 FRAME SCHEMATIC DIAGRAM (1/2)
Page 51 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E FRAME SCHEMATIC DIAGRAM-2 FRAME SCHEMATIC DIAGRAM (2/2)
Page 52 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E CD-212 (CCD IMAGER) PRINTED WIRING BOARD (720H MODEL) 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS — Ref. No. CD-212 Board; 10,000 Series — CD-212 BOARD THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS C1401 (In addition to this, the necessary note is printed in each block)
Page 53 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E CD-213 (CCD IMAGER) PRINTED WIRING BOARD (960H MODEL) — Ref. No. CD-213 Board; 10,000 Series — CD-213 BOARD C2401 C2402 C2403 C2404 C2406 C2407 C2408 C2409 C2410 C2411 CN2401 B-3 IC2401 A-3 IC2402 B-2 IC2403 B-2...
Page 54 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (1/13) IC501 5 IC502 !º CAMERA REC/PB CAMERA REC 3.0Vp-p NTSC: 27.00 MHz 2.9Vp-p NTSC:74 nsec PAL: 36.00 MHz PAL:56 nsec IC501 !¡...
Page 55 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (2/13) IC251 $¶, L257 LINE REC/PB 3.0Vp-p NTSC :13.3 MHz PAL : 13.6 MHz Y/C PROCESSOR 4-18 4-19 4-20 VC-213 (2/13)
Page 56 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. LENS MOTOR DRIVE 4-21 4-22 VC-213 (3/13)
Page 57 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (4/13) !¡ IC643 7 CAMERA REC/PB 2Vp-p !™ IC643 9 CAMERA REC/PB IR ON 0.5Vp-p !£ IC643 !™ CAMERA REC/PB 1.0Vp-p !¢...
Page 58 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (5/13) !• Q351 E CAMERA REC/PB 0.15Vp-p !• Q351 E LINE REC 0.4Vp-p !ª Q352 E CAMERA REC/PB 0.4Vp-p !ª...
Page 59 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (6/13) CAMERA REC/PB @¡ IC301 !¢ (R315) 2.6Vp-p 24.58MHz SFD, TFD, LIP 4-32 4-33 4-34 VC-213 (6/13)
Page 60 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (7/13) @™ IC102 1,2,5,6 CAMERA REC 3.6Vp-p 13.3 msec @£ IC102 @¶,@ª PB (8mm) 0.15Vp-p NTSC : 33.3 msec PAL : 40.0 msec @£...
Page 61 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (8/13) @∞ IC201 #£ PB (DV) 0.3Vp-p 13.3 msec 8MM PB RF AMP, D/A CONVERTER 4-40 4-41 4-42 VC-213 (8/13)
Page 62 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. 8MM AFM PROCESSOR 4-43 4-44 4-45 4-46 VC-213 (9/13)
Page 63 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (10/13) CAMERA REC/PB @§ IC902 1 (X901) 2.5Vp-p 20.0MHz 8MM MECHANISM CONTROL 4-48 4-49 4-50 VC-213 (10/13)
Page 64 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. DV MECHANISM CONTROL 4-51 4-52 4-53 VC-213 (11/13)
Page 65 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E For schematic diagram FP-249 (S/T REEL SENSOR), FP-356 (TOP SENSOR), FP-355 (TAPE LED) FLEXIBLE BOARD • Refer to page 4-65 for printed wiring board. — Ref. No. FP-249, 356, 355 FLEXIBLE board; 20,000 series — VC-213 BOARD (12/13) CAMERA REC/PB...
Page 66 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-65 for printed wiring board. VC-213 BOARD (13/13) CAMERA REC/PB #™ IC801 $º 3.2Vp-p 20.0 MHz #£ IC801 %£ 3.2Vp-p 32.768 KHz HI CONTROL 4-59 4-60 4-61 4-62 VC-213 (13/13)
Page 67 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E VC-213 (CAMERA PROCESSOR, Y/C PROCESSOR, LENS MOTOR DRIVE, IN/OUT SELECT, IR TRANSMITTER, BASE BAND INPUT, VFD, SFD, TFD, LIP, TRX, TRW, 8MM PB RF AMP, D/A CONVERTER, 8MM AFM PROCESSOR, 8MM MECHANISM CONTROL, DV MECHANISM CONTROL, SERVO, HI CONTROL) PRINTED WIRING BOARD —...
Page 68 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E VC-213 BOARD (SIDE B) C101 C-13 C267 G-11 C691 G-12 FB505 G-14 Q208 E-13 R203 D-13 R323 A-18 R525 F-13 R526 G-14 C123 A-15 C268 F-12 C692 G-12 FB506 F-12 Q209 E-14 R204 D-13...
Page 69 Note : This series use the three different types of printed wiring board as shown below. DD-117 • Chip parts DCR-TRV103/TRV110/TRV110E/TRV110P : SE-86 : 1-673-116- (DC/DC CONVERTER) Note : This series use the three different types of printed wiring board as shown below.
Page 70 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E STEADY SHOT AV IN/OUT 4-73 4-74 SE-86/87/89 PJ-95/96/98...
Page 71 R321 C345 R323 C346 R324 Note : This series use the three different types of printed wiring board as shown below. C347 R325 DCR-TRV103/TRV110/TRV110E/TRV110P : MA-354 : 1-673-155- C348 R326 C349 R327 DCR-TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315 : MA-355 : 1-673-167- C350 R331 DCR-TR7000/TR7000E/TR7100E : MA-357 : 1-673-163-...
Page 72 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E STEREO MIC AMP 4-77 4-78 MA-354/355/357...
Page 73 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E CF-62 (USER CONTROL) PRINTED WIRING BOARD (2.5 INCH LCD MODEL) — Ref. No. CF-62 Board; 7,000 Series — CF-62 BOARD BH001 D-5 R013 R015 C001 D-10 R016 C002 D-10 R022 C003 D-11 R023 R025 CN001 B-11 R026 CN002 A-14 R029...
Page 74 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E USER CONTROL 4-83 4-84 4-85 CF-62...
Page 75 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E CF-63 (USER CONTROL) PRINTED WIRING BOARD (3/3.5 INCH LCD MODEL) — Ref. No. CF-63 Board; 8,000 Series — CF-63 BOARD BH001 B-2 R009 R013 C001 B-16 R015 C002 B-16 R022 C003 C-16 R023 D-11 R025 CN001 A-13 R028 CN002 A-17...
Page 76 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DCR-TR7000/TR7000E/TR7100E USER CONTROL 4-91 4-92 4-93 CF-63, FP-62, PS-9500...
Page 77 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E CF-65 (USER CONTROL) PRINTED WIRING BOARD (TR MODEL) — Ref. No. CF-65 Board; 9,000 Series — CF-65 BOARD BH001 B-11 R011 R012 BZ001 C-16 R013 BZ002 B-16 R014 R016 C-13 C001 R022 C002...
Page 78 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E USER CONTROL 4-99 4-100 4-101 CF-65/FP-62...
Page 79 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E PD-105 (RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE) PRINTED WIRING BOARD (2.5 INCH LCD MODEL) — Ref. No. PD-105 Board; 10,000 Series — PD-105 BOARD C5501 L5501 R5641 C-8 C5502 L5502 R5643 D-5 C5503 L5503 R5644 C-3 C5504...
Page 80 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E PD-106 (RGB DECODER, LCD, TIMING GENERATOR, BACK LIGHT DRIVE) PRINTED WIRING BOARD (3/3.5 INCH LCD MODEL) — Ref. No. PD-106 Board; 10,000 Series — PD-106 BOARD C5501 L5503 R5644 C-4 C5502 L5504 C-10 R5646 C-5 C5503 C-10...
Page 81 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-103 for printed wiring board. PD-105 BOARD (1/2) CAMERA REC/PB IC5801 2 3.0Vp-p 24.152 KHz IC5502 8 0.4Vp-p IC5502 9 0.3Vp-p IC5502 !º 0.1Vp-p IC5502 @º...
Page 82 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-105 for printed wiring board. PD-106 BOARD (1/2) CAMERA REC/PB IC5900 2 3.0Vp-p 25.523 KHz IC5502 8 0.4Vp-p IC5502 9 0.3Vp-p IC5502 !º 0.1Vp-p IC5502 @º 4.0Vp-p IC5502 @™ 4.0Vp-p IC5502 @¢...
Page 83 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E For schematic diagram • Refer to page 4-103 for printed wiring board of PD-105 board. • Refer to page 4-105 for printed wiring board of PD-106 board. PD-105 BOARD (2/2) CAMERA REC/PB IC5601 @§ 4.3Vp-p 5.82 MHz IC5601 #¶...
Page 84 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E VF-129 (B/W EVF) PRINTED WIRING BOARD (B/W EVF MODEL) — Ref. No. VF-129 Board; 6,000 Series — VF-129 BOARD VF-129 BOARD C901 R905 CAMERA REC/PB C902 R906 C903 R907 IC901 1,5 C904 R908 C905 R909 C906 R910...
Page 85 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E VF-126 (COLOR EVF) PRINTED WIRING BOARD (COLOR EVF MODEL) — Ref. No. VF-126 Board; 10,000 Series — VF-126 BOARD C4501 D4601 D-8 R4524 B-8 C4502 D4602 D-1 R4525 B-8 C4503 D4801 E-4 R4526 B-8 C4504...
Page 86 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E VF-126 BOARD CAMERA REC/PB IC4501 8 IC4502 @¶ 2.8Vp-p 0.55Vp-p IC4501 9 IC4502 $¡ 0.2Vp-p 11MHz 2.3Vp-p !º IC4501 !º IC4502 $∞ 2.8Vp-p 0.3Vp-p IC4501 @º 8.0Vp-p IC4501 @™ 8.0Vp-p IC4501 @¢ 8.0Vp-p IC4601 !∞ 11.0Vp-p COLOR EVF...
Page 87 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E DD-117 (DC/DC CONVERTER) PRINTED WIRING BOARD — Ref. No. DD-117 Board; 6,000 Series — DD-117 BOARD C801 D806 Q828 R852 C802 D809 Q829 R853 C803 D810 Q830 R854 C804 D812 Q831 R859 C805...
Page 88 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E DD-117 BOARD CAMERA REC/PB IC801 4 0.75Vp-p 2 µsec IC801 ^¢ 0.75Vp-p 2 µsec DC/DC CONVERTER 4-131 4-132 4-133 4-134 DD-117...
Page 89 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E DCR- TR7000/TR7000E/TR7100E CONTROL SWITCH BLOCK 4-138E FK-8500/SS-8500...
Page 90: Before Starting Adjustment
DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Page 91 1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by r in the following table. Replaced parts Block replacement Mounted parts replacement Adjustment Adjustment Section Initialization Initialization of C page data of C, D, E, F...
Page 92 When replacing a board or EEPROM, adjust the items indicated by r in the following table. Note 1: *1 : Color EVF model (DCR-TR7000/TR7000E/TR7100E/ Replaced parts TRV315) only. Board *2 : B/W EVF model (DCR-TRV103/TRV110/TRV110E/ replacement TRV110P/TRV203/TRV210/TRV210E/ TRV310/TRV310E/TRV310P) only. *3 : TRV model (DCR-TRV103/TRV110/TRV110E/TRV110P/ TRV203/TRV210/TRV210E/TRV310/ TRV310E/TRV310P/TRV315) only.
Page 93: Camera Section Adjustment
5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...
Page 94 Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. Note 3: 2.5 LCD model: DCR-TRV103/TRV110/TRV110E/TRV110P 3/3.5 LCD model: DCR-TRV203/TRV210/TRV210E/TRV310/ TRV310E/TRV310P/TRV315 TR model: DCR-TR7000/TR7000E/TR7100E MA board CF board 1.5 m...
Page 95 2.5 LCD MODEL (DCR-TRV103/TRV110/TRV110E/TRV110P) Note 1 : Press the battery switch of the battery terminal using adhesive tape, etc. Note 2 : 720H model : DCR-TRV103/TRV110/TRV110P 960H model : DCR-TRV110E Color monitor Vector scope Regulated power supply (Note 1) Terminated at 75 Ω...
Page 96 3/3.5 LCD MODEL (DCR-TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315) Note 1 : Press the battery switch of the battery terminal using adhesive tape, etc. Note 2 : 720H model : DCR-TRV203/TRV210/TRV310/TRV310P/TRV315 960H model : DCR-TRV210E/TRV310E Note 3 : Color EVF model : DCR-TRV315 Color monitor Vector scope Regulated power supply (Note 1)
Page 97 TR MODEL (DCR-TR7000/TR7000E/TR7100E) Note 1 : Press the battery switch of the battery terminal using adhesive tape, etc. Note 2 : 720H model : DCR-TR7000 960H model : DCR-TR7000E/TR7100E Color monitor Vector scope Regulated power supply (Note 1) Terminated at 75 Ω (8.4 ±...
Page 98 1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. Note: TRV model : DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315 POWER switch (MA-354/355/357 board) .... CAMERA FOCUS switch (MR-8500 block) ......MANUAL NIGHT SHOT switch (Lens block) ......... OFF PROGRAM AE (CF-62/63/65 board) ......
Page 99 1-2. INITIALIZATION OF C, D, E, F PAGE DATA 3. C Page Table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the C Page Data”.) 1-2-1. INITIALIZATION OF C PAGE DATA Fixed data-2 : Modified data. (Refer to “2. Modification of C Page 1.
Page 100 Address Initial value Remark Address Initial value Remark NTSC NTSC Emergency memory address Fixed data-1 (Initialized data) Fixed data-1 (Initialized data) PLL f fine adj. Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2...
Page 101 1-2-2. INITIALIZATION OF D PAGE DATA 1. Initializing the D Page Data Address Initial value Remark Note: If the D Page data has been initialized, “Modification of D Page NTSC Data” and following adjustments need to be performed again. Fixed data-2 1) Color viewfinder system adjustments Fixed data-1 2) LCD system adjustments...
Page 102 Address Initial value Remark Address Initial value Remark NTSC NTSC Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2...
Page 103 Bright adj. (LCD) (Note2) Color adj. (LCD) 80/8D 80/8D Contrast adj. (LCD) (Note2) Fixed data-1 (Initialized data) Note 2: LCD TYPE S / LCD TYPE C LCD TYPE S model:DCR-TRV103/TRV110/TRV110E/ TRV110P/TRV203/TRV210/TRV210E/ TRV310E/TRV315 LCD TYPE C model: DCR-TRV310/TRV310P Table. 5-1-3. 5-14...
Page 104 1-2-3. INITIALIZATION OF E, F PAGE DATA 3. F Page table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the E, F 1. Initializing the E, F Page Data Page Data”.) Note: If the E, F page data has been initialized, “Modification of E, F Fixed data-2 : Modified data.
Page 105 Address Initial value Remark Address Initial value Remark NTSC NTSC Hi8/standard 8 mm 14MHz origin Fixed data-1 osc. adj. (Initialized data) BBI PLL adj. Fixed data-1 (Initialized data) HALL adj. Fixed data-2 Fixed data-1 Fixed data-2 Fixed data-1 (Initialized data) Color reproduction adj.
Page 106 Address Initial value Remark Address Initial value Remark NTSC NTSC Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Flange back adj. Color reproduction adj. Fixed data-1 (Initialized data) Table.
Page 107 4. E Page Table Address Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the E, F Page Data”.) Fixed data-1 Fixed data-2 : Modified data. (Refer to “2. Modification of E, F Page Data”.) (Initialized data) Address Remark Fixed data-1 (Initialized data)
Page 108 Address Remark Address Remark Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) 5-19...
Page 109 Address Remark Fixed data-1 (Initialized data) Table. 5-1-5. 5-20...
Page 110 1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, Check that the specified values of “27/36MHz Origin Oscillation Adjustment”, “S VIDEO OUT Y level Adjustment” and “S VIDEO OUT C level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset.
Page 111 2. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Adjusting method: Subject Siemens star chart with ND filter for 1) Install the minipattern box so that the distance between it and the minipattern box (Note 1) the front of the lens of the camcorder is less than 5 cm.
Page 112 3. Flange Back Adjustment 3-2. Flange Back Adjustment (2) (Using Flange Back Adjustment Chart Subject More Perform this adjustment after performing “Flange Back Adjustment Than 500 m Away) (1)”. The inner focus lens flange back adjustment is carried out Subject Subject more than 500m away automatically.
Page 113 4. Flange Back Check 5. Picture Frame Setting Subject Siemens star Subject Color bar chart (2.0 m from the front of the lens) (Color reproduction adjustment frame) (Luminance : approx. 200 lux) (1.5m from the front of the lens) Measurement Point Check operation on TV monitor Measurement Point Video output terminal...
Page 114 6. AGC Gain Calibration Adjustment Subject Clear chart (Color reproduction adjustment frame) Measurement Point Display data of page 1 (Note) Measuring Instrument Adjustment remote commander Adjustment Page Adjustment Address 2E, 2F, 30, 31 Specified Value Data1 : 0196 to 0283 Data2 : 0C97 to 13F4 Note: Displayed data of page 1 of the adjustment remote commander.
Page 115 7. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. NTSC 720H model Subject Color bar chart (Color reproduction adjustment frame) Measurement Point Video output terminal Measuring Instrument Vectorscope Adjustment Page Adjustment Address 4E, 50, FB, FC Specified Value All color luminance points should...
Page 116 8. IRIS IN/OUT Adjustment For the unit to judge if the white balance is indoors or outdoors in auto white balance operations, measure the light level and write it in the EEPROM. If the level is not correct, the white balance will not be accurate. Subject Clear chart (Color reproduction adjustment frame)
Page 117 9. Auto White Balance Standard Data Input 10. Auto White Balance Adjustment Adjust to the proper auto white balance output data. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color reproduction adjustment frame) be poor.
Page 118 11. White Balance Check Subject Clear chart (Color reproduction adjustment frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.3 Measurement Point Video output terminal Measuring Instrument Vectorscope Specified Value Fig. 5-1-13. A to C Fig. 5-1-13. (A) Switch setting: NIGHT SHOT ..............
Page 119 12. Angular Velocity Sensor Sensitivity Data check • This adjustment is performed only when replacing the angular velocity sensor. Although this adjustment need not be performed when the circuit is damaged, etc., check the operations. • Note down the sensitivity displayed on the angular velocity sensor of the repair parts.
Page 120 1-4. COLOR ELECTRONIC VIEWFINDER 1. EVF Initial Data Input SYSTEM ADJUSTMENTS Mode Camera (DCR-TR7000/TR7000E/TR7100E/TRV315) Subject Arbitrary Adjustment Page Note 1: The back light (fluorescent tube) is driven by a high voltage AC Adjustment Address 70 to 76, 78 to 7C power supply.
Page 121 2. VCO Adjustment (VF-126 board) 3. Bright Adjustment (VF-126 board) Set the VCO free-run frequency. If deviated, the EVF screen will be Set the level of the VIDEO signal for driving the LCD to the specified blurred. value. If deviated, the screen image will be blackish or saturated (whitish).
Page 122 4. Contrast Adjustment (VF-126 board) 5. Backlight Consumption Current Adjustment Set the level of the VIDEO signal for driving the LCD to the specified (VF-126 board) value. If deviated, the screen image will be blackish or saturated Set the backlight luminance and color temperature. (whitish).
Page 123 6. White Balance Adjustment (VF-126 board) Correct the white balance. If deviated, the reproduction of the EVF screen may degenerate. Mode Camera Subject Arbitrary Measurement Point Check on EVF screen Measuring Instrument Adjustment Page Adjustment Address 71, 72 Specified Value The EVF screen should not be colored.
Page 124 DCR-TRV103/TRV110/TRV110E/TRV110P/ Signal Hi8/standard 8mm alignment tape : TRV203/TRV210/TRV210E/TRV310/ For checking operation TRV310E/TRV310P (WR5-8NSE(NTSC)) (WR5-8CSE(PAL)) Note: NTSC model: DCR-TRV103/TRV110/TRV110P/TRV203/TRV210/ Monoscope section TRV310/TRV310P Specified Value ± 4% PAL model: DCR-TRV110E/TRV210E/TRV310E Adjustment method: 1-5-1. Horizontal Slant Check Use the centering adjustment ring and adjust so that the left,...
Page 125 1-5-4. Aberration Adjustment 1-5-5. Horizontal Amplitude Adjustment (VF-129 board) Mode VTR stop Mode Playback Signal Dot pattern Signal Hi8/standard 8mm alignment tape : 2 × a1 For checking operation Specified Value 0.8 × a2 (WR5-8NSE(NTSC)) (WR5-8CSE(PAL)) Monoscope section Adjustment method: 1) Adjust the aberration adjustment ring so that the tracing of the Adjusting Element C909 (SOL901)
Page 126 1-5-6. Vertical Amplitude Adjustment (VF-129 board) 1-5-7. Brightness Adjustment (VF-129 board) Mode Playback Mode Playback Signal Hi8/standard 8mm alignment tape : Signal Hi8/standard 8mm alignment tape : For checking operation For checking operation (WR5-8NSE(NTSC)) (WR5-8NSE(NTSC)) (WR5-8CSE(PAL)) (WR5-8CSE(PAL)) Monoscope section Monoscope section Adjusting Element RV903 Adjusting Element...
Page 127 3 LCD 3.5 LCD 2.5 LCD model PD-105 Fixed data 3/3.5 LCD model PD-106 Fixed data Note 5: LCD TYPE S model: DCR-TRV103/TRV110/TRV110E/ TRV110P/TRV203/TRV210/TRV210E/ 2. LCD Initial Data Input (2) TRV310E/TRV315 Mode VTR stop LCD TYPE C model: DCR-TRV310/TRV310P Signal...
Page 128 A = 1.70 V (LCD TYPE C) – 0.05 Adjustment Address Specified Value A=3.42 ± 0.05V (LCD TYPE S) Note : LCD TYPE S model: DCR-TRV103/TRV110/TRV110E/TRV110P/ A=3.01 ± 0.05V (LCD TYPE C) TRV203/TRV210/TRV210E/TRV310E/ TRV315 LCD TYPE C model: DCR-TRV310/TRV310P Adjusting method: Select page: 0, address: 01, and set data: 01.
Page 129 A=2.38 ± 0.07V (LCD TYPE C) A=1.34 ± 0.05V (LCD TYPE C) Adjusting method: Note : 2.5 LCD TYPE S model: DCR-TRV103/TRV110/TRV110E/ 1) Select page: 0, address: 01, and set data: 01. TRV110P/ 2) Select page: 3, address: 0C, set data: 60, and press the PAUSE 3/3.5 LCD TYPE S model: DCR-TRV203/TRV210/TRV210E/...
Page 130 Note 1 : Perform “Bright Adjustment” and “Contrast Adjustment” before Note : 2.5 LCD TYPE S 61k NTSC model :DCR-TRV103/TRV110/ this adjustment. TRV110P Note 2 : 2.5 LCD TYPE S 61k NTSC model : DCR-TRV103/TRV110/ 2.5 LCD TYPE S 84k PAL model : DCR-TRV110E TRV110P (AEP,UK,EE,NE,RU) 2.5 LCD TYPE S 84k PAL model : DCR-TRV110E...
Page 131 1. LCD panel 2. Light induction plate Note : Perform “Bright Adjustment” and “Contrast Adjustment” before this 3. IC5502 adjustment. Note 2 : LCD TYPE S model: DCR-TRV103/TRV110/TRV110E/ TRV110P/TRV203/TRV210/TRV210E/ Adjusting method: TRV310E/TRV315 1) Select page: 0, address: 01, and set data: 01.
Page 132: Mechanism Section
5-2. MECHANISM SECTION ADJUSTMENT Mechanism Section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “8mm Video Mechanism Adjustment Manual B Mechanism ”. Note 1: NTSC model: DCR-TR7000/TRV103/TRV110/TRV110P/ 2-1-2. TAPE PATH ADJUSTMENT TRV203/TRV210/TRV310/TRV310P/TRV315 PAL model: DCR-TR7000E/TR7100E/TRV110E/TRV210E/ 1. Preparations for Adjustment TRV310E Clean the tape path face (tape guide, capstan shaft, pinch roller).
Page 133 2-2. DIGITAL8 MODE 2-2-3. OVERALL TAPE PATH CHECK 2-2-1. HOW TO ENTER RECORD MODE WITHOUT 1. Recording of the tape path check signal CASSETTE 1) Clean the tape running side (tape guide, capstan shaft, pinch roller). 1) Connect the adjustment remote commander to the LANC jack. 2) Connect the adjustment remote commander to the LANC jack.
Page 134: Video Section Adjustment
5-3. VIDEO SECTION ADJUSTMENT 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. Note: NTSC model:DCR-TR7000/TRV103/TRV110/TRV110P/TRV203/ TRV210/TRV310/TRV310P/TRV315 PAL model: DCR-TR7000E/TR7100E/TRV110E/TRV210E/ TRV310E 3-1-1. Equipment to Required 13) PAL Hi8/standard8 mm alignment tapes (For PAL model) TV monitor •...
Page 135 3) Select page: 0, address: 01, and set data: 00. even if even if the cabinet (R) block ( Camera function switch Note 4: 2.5 LCD model : DCR-TRV103/TRV110/TRV110E/TRV110P (CF-62/63/65 board), LCD block (TRV model only), 3/3.5 LCD model : DCR-TRV203/TRV210/TRV210E/TRV310/ viewfinder.
Page 136 3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-213 board CN910. Connect the measuring instruments via CN910 the CPC-13 jig (J-6082-443-A). The following table lists the pin numbers and signal names of CN910. Pin No.
Page 137 3-1-5. Alignment Tape The following table lists alignment tapes which are available. Use the tape specified in the signal column for each adjustment. If the type of tape to be used for checking operations is not specified, use whichever type. Digital8 alignment tape Name Usage...
Page 138 Fig. 5-3-3. Shows the color bar signals recorded on the alignment tape. Note : Measure using the VIDEO terminal (Terminated at 75 Ω). For NTSC model White (100%) White (75%) Burst signal 0.714V (75%) 0.286V Black 0.286V White (100%) Horizontal sync signal Color bar signal waveform Color bar pattern For PAL model...
Page 139 Switch setting 1) AUTO FOCUS ..............OFF 2) LCD screen (TRV model) ..........Closed 3) NIGHT SHOT ..............OFF Digital voltmeter Note 2: TRV model:DCR-TRV103/TRV110/TRV110E/TRV110P/ TRV203/TRV210/TRV210E/TRV310/ TRV310E/TRV310P/TRV315 Fig. 5-3-4. Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig.
Page 140 3-3. SERVO AND RF SYSTEM ADJUSTMENTS 2. Switching Position Adjustment (VC-213 board) To obtain normal playback waveform output, adjust the switching Before perform the servo and RF system adjustments, check that position. the specified value of “27 MHz/36MHz Origin Oscillation Adjustment”...
Page 141 3. AGC Center Level Adjustment (VC-213 board) 4. APC & AEQ Adjustment (VC-213 board) Mode Camera record and playback Mode Camera record and playback Subject Arbitrary Subject Arbitrary Pin !§ of CN910 (RF MON) (Note 1) Pin !§ of CN910 (RF MON) (Note 1) Measurement Point Measurement Point External trigger : Pin !£...
Page 142 5. PLL f & LPF f Final Adjustment (VC-213 board) 6. Hi8/standard 8mm Switching Position Adjustment (VC-213 board) Mode VTR stop If deviated in this case causes switching noise or jitter on the Hi8/ Signal Arbitrary standard 8mm mode played back screen. Measurement Point Display data of page: 3, address: 03 Mode...
Page 143 7. CAP FG Offset Adjustment (VC-213 board) Improve the capstan servo characteristic. If it is not correct. jitters will increase. Mode Playback Signal Hi8/standard 8mm alignment tape : For checking operation (WR5-5NSP(NTSC)) (WR5-5CSP(PAL)) Pin !∞ of CN910 (CAP FG) Measurement Point Measuring Instrument Oscilloscope Adjustment Page...
Page 144 3-4. VIDEO SYSTEM ADJUSTMENTS 2. Chroma BPF f Adjustment (VC-213 board) Set the center frequency of IC643 chroma band-pass filter. 3-4-1. Video System Adjustments Mode VTR stop Signal No signal Adjusting Procedure: Measurement Point CH1: Chroma signal terminal of 27MHz/36MHz origin oscillation adjustment S VIDEO jack (75Ω...
Page 145 3. S VIDEO OUT Y Level Adjustment (VC-213 board) 4. S VIDEO OUT Chroma Level Adjustment (VC-213 board) Mode Camera Mode Camera Subject Arbitrary Subject Arbitrary Measurement Point Y signal terminal of S VIDEO jack (75Ω terminated) Measurement Point Chroma signal terminal of S VIDEO jack (75Ω...
Page 146 5. VIDEO OUT Y, Chroma Level Check (VC-213 board) 6. Hi8/standard 8mm 14 MHz Origin Oscillation Adjustment (VC-213 board) Mode Camera Set the oscillation frequency of X251 for the Hi8/standard 8mm Subject Arbitrary playback operation. Measurement Point VIDEO jack (75Ω terminated) If deviated, the synchronization will be disrupted and the color will Measuring Instrument Oscilloscope...
Page 147 7. BBI PLL Adjustment (VC-213 board) 8. Hi8/standard 8mm Y Level Adjustment Set the VCO center level of the video input circuit (IC601). (VC-213 board) Set the Hi8/standard 8mm PB Y signal level. (Adjust the D/A Mode VTR stop converter out put level of IC251.) Signal No signal Mode...
Page 148 9. Hi8/standard 8mm Chroma Level Adjustment 10. Hi8/standard 8mm AFC f Adjustment (VC-213 board) (VC-213 board) Set the Hi8/standard 8mm PB Chroma signal level. (Adjust the D/ Adjust the pull-in range of the clock generator (IC251) for A/D A converter out put level of IC251.) conversion during Hi8/standard 8mm playback.
Page 149 11. Hi8/standard 8mm RP Filter f Adjustment (VC-213 board) Adjust the LPF of the playback RF amplifier (IC201). Mode VTR stop Signal No signal Pin 7 of CN910 (RF AGC OUT) Measurement Point Measuring Instrument Oscilloscope Adjustment Page Adjustment Address Specified Value A= Minimum Connection:...
Page 150 3-4-2. BIST Check 1. Playback System Check 1-1. Preparation for Playback Set the POWER switch to VTR (or PLAYER) position. When the playback system from IC301(SFD) to IC702 (ADC&DAC) is normal, the display data (combination data) Connect the adjusting remote commander and set the HOLD switch to ON (SERVICE) position.
Page 151 1-5. IC351(VFD) BIST(PB) Check • UPY Cb BIST(PB) Check 1) Select page: 0, address: 01, and set data: 01. 19) Select page: 3, address: 10, set data: 8A, and press the PAUSE 2) Select page: C, address: 51, set data: 0F, and press the PAUSE button.
Page 152 • ENC Ca BIST(PB) Check 34) Select page: 3, address: 10, set data: 8D, and press the PAUSE button. 35) Select page: 3, address: 12, set data: 10, and press the PAUSE button. 36) Select page: 3, address: 12, set data: 00, and press the PAUSE button.
Page 153 2. Recording System Check 9) Select page: 3, address: 11, set data: 87, and press the PAUSE button. 2-1. Preparations for recording 10) Select page: 3, address: 12, set data: 08, and press the PAUSE 1) Playback the BIST check tape.(WR5-6ND(NTSC), WR5- button.
Page 154 2-5. IC104(TRX) BIST(REC) Check Select page: 3, address: 12, set data: 04, and press the PAUSE button. Select page: 3, address: 12, set data: 00, and press the PAUSE button. Select page: 3, address: 13, set data: 02, and press the PAUSE button.
Page 155 3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-213 board) Mode VTR stop Adjust using a IR receiver jig (J-6082-383-A). Signal No signal Measurement Point VIDEO OUT terminal of IR receiver jig Switch setting: (Terminated at 75Ω) LASER LINK ......ON (Red LED is lit) Measuring Instrument Oscilloscope 1.
Page 156 3. IR Audio Deviation Adjustment (VC-213 board) Adjusting method: Select page: 0, address: 01, and set data: 01. Mode VTR stop Only for the TR model (Note), Select page: D, address: 1B, set Signal Audio signal : data: 01, and press the PAUSE button of the adjustment remote 400Hz, –7.5dBs : L and R of commander.
Page 157 3-6. AUDIO SYSTEM ADJUSTMENTS 1. Hi8/standard 8mm AFM BPF f Adjustment (VC-213 board) Sets the BPF passing frequency of IC760 so that the AFM signal [Connecting the measuring instruments for the audio] can separate from the playback RF signal properly. If deviated. the Connect the audio system measuring instruments in addition to the mono/stereo mode will be differentiated incorrectly, and noises and video system measuring instruments as shown in Fig.
Page 158 2. Hi8/standard 8mm AFM 1.5 MHz Deviation 4. Digital8 Playback Level Check Adjustment (VC-213 board) Mode VTR playback Adjust to the optimum 1.5MHz audio FM signal deviation. Signal Digital8 alignment tape: If the adjustment is not correct, its playback level will differ from For audio operation check that of other units.
Page 159 7. Overall Noise Level Check Mode Camera recording and playback Signal No signal: Insert a shorting plug in the MIC jack Measurement Point Audio output terminal left or right Measuring Instrument Audio level meter Specified Value Below –45dBs (IHF-A filter ON, 20kHz LPF ON) Checking Method: 1) Insert a shorting plug in the MIC jack.
Page 160: Service Mode
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions Upon Using the Adjustment Remote Commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
Page 161 4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 162 4-3. SERVICE MODE 2. Emergence Memory Address 2-1. C Page. Emergence Memory Address Additional note on adjustment Note: After the completion of the all adjustments, cancel the service mode Page C Address 38 to 43 by either of the following ways. 1) After data on page: D and F is restored, unplug the main power Address Contents...
Page 163 2-2. F Page Emergence Memory Address 2-3. EMG Code (Emergency Code) Note 1: Emergence of PB mode only. Codes corresponding to the errors which occur are written in C page, addresses 38, 3C and 40 (or F page, addresses 10, 14 and 18). The type of error indicated by the code are shown in the following Page F Address 10 to 1B...
Page 164 2-4. MSW Code • The lower parts of the data of C page, addresses 3A, 3E and 42 (or F page, addresses 12, 16 and 1A) represent the MSW codes (mode switch mechanism position) when errors occurs. • The upper parts of the data of C page, addresses 3A, 3E and 42 (or F page, addresses 12, 16 and 1A) represent, when the mechanism position is to be moved, the MSW codes at the start movement (when moving the loading motor).
Page 165 3. Bit Value Discrimination Bit values must be discriminated using the display data of the Display on the Bit values adjustment remote commander for the following items. Us the table adjustment bit3 bit2 bit1 bit0 below to discriminate if the bit value is “1” or “0”. remote commander bit7...
Page 166 63/65 board BH001) is removed (reset). Note: CF-62 board 2.5 LCD model CF-63 board 3/3.5 LCD model CF-65 board TR model 2.5 LCD model: DCR-TRV103/TRV110/TRV110E/TRV110P 3/3.5 LCD model: DCR-TRV203/TRV210/TRV210E/TRV310/ TRV310E/TRV310P/TRV315 TR model: DCR-TR7000/TR7000E/TR7100E 7. Switch check (1) Page 2 Address 43 Function...
Page 167 PD-105 board 2.5 LCD model CF-63 board PD-106 board 3/3.5 LCD model CF-65 board — TR model 2.5 LCD model: DCR-TRV103/TRV110/TRV110E/TRV110P 3/3.5 LCD model: DCR-TRV203/TRV210/TRV210E/TRV310/ TRV310E/TRV310P/TRV315 TR model: DCR-TR7000/TR7000E/TR7100E 9. AUDIO(L) jack check Page 2 Address 42 Function When bit value = 1...
Page 168: Exploded Views
DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR-TR7000/TR7000E/TR7100E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • Abbreviation CND : Canadian model • -XX, -X mean standardized parts, so they may The components identified by mark ! or : East European model have some differences from the original one.
Page 169 6-1-2. CABINET (R) BLOCK ASSEMBLY (TR MODEL) (TR7000/TR7000E/TR7100E) Color EVF block assembly (See page 6-9) not supplied not supplied not supplied LED901 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-418-274-11 SWITCH BLOCK, CONTROL (PS-9500) 3-053-690-01 RETAINER (93), MF 3-948-339-61 TAPPING 3-054-029-01 BUTTON (952), POWER LOCK...
Page 170 6-1-3. CABINET (R) BLOCK ASSEMBLY (2.5 INCH LCD MODEL) (TRV103/TRV110/TRV110E/TRV110P) LCD block assembly (2.5 INCH LCD MODEL) (See page 6-6) B/W EVF block assembly (See page 6-8) supplied SP901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-418-274-11 SWITCH BLOCK, CONTROL (PS-9500) 3-054-038-01 COVER (R) (952), HINGE...
Page 171 6-1-4. CABINET (R) BLOCK ASSEMBLY (3.0/3.5 INCH LCD MODEL) (TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315) B/W EVF block assembly (See page 6-8) LCD block assembly (3.0/3.5 INCH LCD MODEL) (See page 6-7) Color EVF block assembly (See page 6-9) SP901 Ref. No. Part No. Description Remarks Ref.
Page 172 6-1-5. CABINET (L) BLOCK AND MAIN BOARDS ASSEMBLY Note: AEP, UK, EE, NE, RU model only supplied Note supplied supplied J001 supplied supplied supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-713-786-21 SCREW (M2X3) * 225 3-053-745-01 PROTECTOR, LS FLEXIBLE 3-968-729-01 SCREW (M2), LOCK ACE, P2 1-672-672-11 FP-45 FLEXIBLE BOARD (TRV110:BR)
Page 173 6-1-6. LCD BLOCK ASSEMBLY (2.5 INCH LCD MODEL) (TRV103/TRV110/TRV110E/TRV110P) supplied LED901 ND901 LCD901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-054-039-01 COVER (C) (952), HINGE 3-053-702-01 HOLDER (93), LCD 3-948-339-11 SCREW, TAPPING X-3949-544-1 CABINET (C) (952) ASSY, P 3-987-623-01 CLAMP, HARNESS 3-054-122-01 WINDOW (952), LCD (TRV110/TRV110P) 1-959-310-11 HARNESS (DP-74)
Page 174 6-1-7. LCD BLOCK ASSEMBLY (3.0/3.5 INCH LCD MODEL) (TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315) supplied LED901 ND901 LCD901 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-054-278-01 COVER (C) (955), HINGE 3-054-275-01 HOLDER (94), LCD 3-948-339-11 SCREW, TAPPING X-3949-450-1 CABINET (C) ASSY (955), P 3-987-623-01 CLAMP, HARNESS (TRV203/TRV210/TRV210E/TRV310:US,HK,E,JE/ 1-959-311-11 HARNESS (DP-75)
Page 175 6-1-8. B/W EVF BLOCK ASSEMBLY (TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P) V901 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-713-786-21 SCREW (M2X3) X-3949-329-1 FINDER (S) ASSY 3-054-068-01 BASE B (95), VF A-7073-838-A VF-129 (N) BOARD, COMPLETE 3-053-685-01 LOCK (93), TILT (TRV103/TRV110/TRV110P/TRV203/TRV210/TRV310/TRV310P) 3-948-339-01 SCREW, TAPPING A-7073-855-A VF-129 (P) BOARD, COMPLETE...
Page 176 6-1-9. COLOR EVF BLOCK ASSEMBLY (TRV315/TR7000/TR7000E/TR7100E) supplied TO CF BOARD Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-968-729-81 SCREW (M2), LOCK ACE, P2 1-672-662-11 FP-47 FLEXIBLE BOARD 3-053-677-01 BASE (C), SLIDE FIXED A-7073-876-A VF-126 BOARD, COMPLETE 3-054-141-01 RETAINER, HARNESS * 412 3-989-416-11 CUSHION (458), LCD...
Page 177 6-1-10. LENS BLOCK ASSEMBLY IC1401, 2401 M906 supplied M905 Be sure to read “Precautions upon replacing CCD imager” on page 4-11,14 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 8-848-729-01 DEVICE, LENS LSV-630A 3-968-054-11 RUBBER (FM), SHIELD X-3949-355-1 IRIS FLEXIBLE ASSY 630 (N) A-7073-865-A CD-212 BOARD, COMPLETE...
Page 178 6-1-11. CASSETTE COMPARTMENT ASSEMBLY LS CHASSIS ASSEMBLY (See page 6-12) MECHANISM CHASSIS ASSEMBLY (See page 6-13) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7040-421-A DAMPER ASSY X-3949-383-2 GEAR ASSY (E), GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4X2.5) X-3949-153-2 CASSETTE COMPARTMENT ASSY 3-727-176-01 WASHER, STOPPER...
Page 179 6-1-12. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-579-01 ROLLER, PINCH PRESS A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT 3-965-557-01 STOPPER (T), GB...
Page 180 6-1-13. MECHANISM CHASSIS ASSEMBLY M901 81 1 supplied M903 M902 S901 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks X-3947-343-1 GROUND (IM) ASSY, SHAFT 3-965-542-01 SHIELD, MOTOR 3-965-550-02 SCREW (M1.7X1.6) 3-965-539-01 GEAR (A) 1-672-542-11 FP-38 FLEXIBLE BOARD 3-965-538-01 SLEEVE, MOTOR HOLDER 3-053-986-01 SPACER (E), CAPSTAN 3-965-540-01 HOLDER, MOTOR...
Page 181: Electrical Parts List
CD-212 CD-213 CF-62/63/65 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, parts list may be different from the parts uH: µH please include the board name. specified in the diagrams or the components •...
Page 182 CF-62/63/65 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < CAPACITOR > R015 1-216-826-11 METAL CHIP 2.7K 1/16W (EXCEPT:TR7000/TR7000E/TR7100E) C003 1-107-826-91 CERAMIC CHIP 0.1uF R016 1-216-826-11 METAL CHIP 2.7K 1/16W (TR7000/TR7000E/TR7100E) R022 1-216-823-11 METAL CHIP 1.5K 1/16W R023 1-216-825-11 METAL CHIP...
Page 183 DD-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7073-866-A DD-117(V) BOARD, COMPLETE C847 1-164-506-11 CERAMIC CHIP 4.7uF (EXCEPT:TRV315/TR7000/TR7000E/TR7100E) C848 1-164-506-11 CERAMIC CHIP 4.7uF C849 1-135-149-21 TANTALUM CHIP 2.2uF ************************* A-7073-917-A DD-117 (C) BOARD, COMPLETE (EXCEPT:TR7000/TR7000E/TR7100E) (TR7000/TR7000E/TR7100E) C850 1-135-149-21 TANTALUM CHIP 2.2uF...
Page 184 DD-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < DIODE > L816 1-414-396-21 INDUCTOR 4.7uH (TRV315/TR7000/TR7000E/TR7100E) D806 8-719-027-76 DIODE 1SS357-TPH3 L817 1-414-396-21 INDUCTOR 4.7uH (EXCEPT:TR7000/TR7000E/TR7100E) L818 1-414-396-21 INDUCTOR 4.7uH D809 8-719-027-77 DIODE MA796-TX (EXCEPT:TR7000/TR7000E/TR7100E) D810 8-719-027-76 DIODE 1SS357-TPH3 L819 1-414-400-11 INDUCTOR...
Page 185 DD-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q838 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) R827 1-216-821-11 METAL CHIP 1/16W (EXCEPT:TR7000/TR7000E/TR7100E) R828 1-216-831-11 METAL CHIP 6.8K 1/16W Q839 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3) R829 1-216-879-11 RES, CHIP 0.50% 1/16W (EXCEPT:TR7000/TR7000E/TR7100E) R830 1-218-883-11 RES, CHIP 1/16W...
Page 186 DD-117 FP-249 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R879 1-216-837-11 METAL CHIP 1/16W R916 1-216-864-11 METAL CHIP 1/16W R880 1-218-895-11 RES,CHIP 100K 0.50% 1/16W (TRV315/TR7000/TR7000E/TR7100E) R881 1-218-877-11 RES,CHIP 0.50% 1/16W R917 1-216-864-11 METAL CHIP 1/16W R882 1-218-903-11 RES,CHIP...
Page 187 D304 8-719-062-16 DIODE 01ZA8.2(TPL3) (TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315) D305 8-749-060-65 DIODE DCC3810 ************************* (Ref.No.:8000 Series) D306 8-719-061-86 DIODE DCR2810 D308 8-719-061-82 DIODE TLSU1002(TPX1,SONY) < CAPACITOR > D309 8-719-073-01 DIODE MA111-(K8).S0 C300 1-162-964-11 CERAMIC CHIP 0.001uF < FUSE > C301 1-162-964-11 CERAMIC CHIP 0.001uF...
Page 188 MA-354/355/357 PD-105/106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R315 1-216-833-11 METAL CHIP 1/16W C5517 1-107-826-91 CERAMIC CHIP 0.1uF R316 1-216-831-11 METAL CHIP 6.8K 1/16W C5518 1-109-982-11 CERAMIC CHIP R317 1-216-832-11 METAL CHIP 8.2K 1/16W C5519 1-104-851-11 TANTAL.
Page 189 PD-105/106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks CN5803 1-778-508-21 PIN, CONNECTOR (PC BOARD) 6P < TRANSISTOR > (TRV103/TRV110/TRV110E/TRV110P) CN5804 1-778-509-21 PIN, CONNECTOR (PC BOARD) 11P Q5501 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) (TRV103/TRV110/TRV110E/TRV110P) Q5601 8-729-042-29 TRANSISTOR RN1104F(TPL3) CN5805 1-691-344-11 CONNECTOR, FFC/FPC (ZIF) 6P Q5602 8-729-042-29 TRANSISTOR RN1104F(TPL3)
Page 190 PD-105/106 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5608 1-216-864-11 METAL CHIP 1/16W R5651 1-218-883-11 RES,CHIP 0.50% 1/16W (EXCEPT:TRV310/TRV310P) (EXCEPT:TRV310/TRV310P) R5610 1-216-842-11 METAL CHIP 1/16W R5652 1-216-864-11 METAL CHIP 1/16W (TRV310/TRV310P) (TRV310/TRV310P) R5610 1-216-845-11 METAL CHIP 100K 1/16W R5652...
Page 191 PD-105/106 PJ-95/96/98 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R5685 1-216-841-11 METAL CHIP 1/16W R5903 1-216-828-11 METAL CHIP 3.9K 1/16W (EXCEPT:TRV310/TRV310P) (TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315) R5685 1-216-842-11 METAL CHIP 1/16W R5904 1-216-832-11 METAL CHIP 8.2K 1/16W (TRV310/TRV310P) (TRV203/TRV210/TRV210E/TRV310/TRV310E/TRV310P/TRV315) R5686 1-216-841-11 METAL CHIP 1/16W...
Page 192 PJ-95/96/98 SE-86/87/89 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < CAPACITOR > L104 1-216-295-91 SHORT 0 (Note 1) (EXCEPT:TRV110E:AEP,UK,EE,NE,RU/TRV210E:AEP,UK/ C101 1-110-569-11 TANTAL. CHIP 47uF 6.3V TRV310E:AEP,UK/TR7000E/TR7100E) C103 1-162-964-11 CERAMIC CHIP 0.001uF L104 1-412-963-11 INDUCTOR 100uH (TRV110E:AEP,UK.EE,NE,RU/TRV210E:AEP,UK/ (TRV110E:AEP,UK.EE,NE,RU/TRV210E:AEP,UK/ TRV310E:AEP,UK/TR7000E/TR7100E)
Page 193 SE-86/87/89 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C614 1-110-501-11 CERAMIC CHIP 0.33uF C112 1-164-943-11 CERAMIC CHIP 0.01uF C616 1-135-259-11 TANTAL. CHIP 10uF 6.3V C113 1-135-259-11 TANTAL. CHIP 10uF 6.3V C617 1-162-970-11 CERAMIC CHIP 0.01uF C115 1-164-943-11 CERAMIC CHIP...
Page 194 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C221 1-164-862-11 CERAMIC CHIP 33PF C311 1-164-850-11 CERAMIC CHIP 10PF 0.5PF C222 1-104-852-11 TANTAL. CHIP 22uF 6.3V C312 1-164-858-11 CERAMIC CHIP 22PF C223 1-164-941-11 CERAMIC CHIP 0.0047uF 10% (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) C224 1-164-943-11 CERAMIC CHIP...
Page 195 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C481 1-107-820-11 CERAMIC CHIP 0.1uF C561 1-164-937-11 CERAMIC CHIP 0.001uF C482 1-164-505-11 CERAMIC CHIP 2.2uF C563 1-164-943-11 CERAMIC CHIP 0.01uF C483 1-107-820-11 CERAMIC CHIP 0.1uF C564 1-135-259-11 TANTAL. CHIP 10uF 6.3V C484...
Page 196 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C647 1-104-851-11 TANTAL. CHIP 10uF C708 1-107-823-11 CERAMIC CHIP 0.47uF C648 1-164-943-11 CERAMIC CHIP 0.01uF C709 1-164-943-11 CERAMIC CHIP 0.01uF C649 1-164-943-11 CERAMIC CHIP 0.01uF C710 1-135-259-11 TANTAL. CHIP 10uF C650 1-109-982-11 CERAMIC CHIP...
Page 197 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C766 1-104-847-11 TANTAL. CHIP 22uF C790 1-165-176-11 CERAMIC CHIP 0.047uF C767 1-162-966-11 CERAMIC CHIP 0.0022uF 10% (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) (TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) C791 1-164-936-11 CERAMIC CHIP 680PF C768 1-164-941-11 CERAMIC CHIP 0.0047uF 10% (TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E)
Page 198 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks CN904 1-766-356-21 CONNECTOR, FFC/FPC 26P FB606 1-500-238-22 FERRITE CN905 1-766-646-21 CONNECTOR, FFC/FPC 10P FB801 1-500-238-22 FERRITE CN906 1-766-342-21 CONNECTOR, FFC/FPC 12P FB901 1-500-238-22 FERRITE CN907 1-766-346-21 CONNECTOR, FFC/FPC 16P CN908 1-766-345-21 CONNECTOR, FFC/FPC 15P <...
Page 199 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks IC801 8-759-589-54 IC S579604PZ-TEB < TRANSISTOR > IC802 8-759-424-79 IC S-8423YFS-T2 IC803 8-759-536-72 IC TL1596CPWR Q101 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) IC901 8-759-445-94 IC AK6480AM-E2 Q102 8-729-042-29 TRANSISTOR RN1104F(TPL3) IC902 8-759-579-24 IC MB91191RPFF-G-133-BND-ER Q103...
Page 200 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q554 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) R113 1-218-990-11 SHORT Q601 8-729-807-86 TRANSISTOR 2SB1295-UL5-TB R114 1-218-979-11 RES,CHIP 150K 1/16W Q602 8-729-037-76 TRANSISTOR UN9215J-(K8).SO R115 1-218-989-11 RES,CHIP 1/16W Q603 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3) R116 1-218-966-11 RES,CHIP 1/16W...
Page 201 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R191 1-218-985-11 RES,CHIP 470K 1/16W R270 1-216-828-11 METAL CHIP 3.9K 1/16W R192 1-218-965-11 RES,CHIP 1/16W R272 1-218-989-11 RES,CHIP 1/16W R195 1-218-969-11 RES,CHIP 1/16W R274 1-218-967-11 RES,CHIP 1/16W R201 1-208-677-11 RES,CHIP 0.50% 1/16W...
Page 202 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R330 1-208-709-11 RES,CHIP 0.50% 1/16W R416 1-218-953-11 RES,CHIP 1/16W (TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) R417 1-218-961-11 RES,CHIP 4.7K 1/16W R331 1-208-703-11 RES,CHIP 6.8K 0.50% 1/16W R418 1-218-990-11 SHORT (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) R419 1-218-977-11 RES,CHIP 100K 1/16W R331...
Page 203 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R485 1-218-965-11 RES,CHIP 1/16W R544 1-218-990-11 SHORT R486 1-218-965-11 RES,CHIP 1/16W R546 1-218-990-11 SHORT R487 1-218-981-11 RES,CHIP 220K 1/16W (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) R488 1-218-981-11 RES,CHIP 220K 1/16W R547 1-218-941-11 RES,CHIP 1/16W R489 1-218-965-11 RES,CHIP...
Page 204 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R641 1-218-973-11 RES,CHIP 1/16W R711 1-218-935-11 RES,CHIP 1/16W R642 1-218-973-11 RES,CHIP 1/16W R712 1-218-957-11 RES,CHIP 2.2K 1/16W R643 1-218-969-11 RES,CHIP 1/16W R713 1-218-953-11 RES,CHIP 1/16W R644 1-218-961-11 RES,CHIP 4.7K 1/16W R714...
Page 205 VC-213 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R805 1-218-953-11 RES,CHIP 1/16W R862 1-218-989-11 RES,CHIP 1/16W (EXCEPT:TR7000/TR7000E/TR7100E) R863 1-218-989-11 RES,CHIP 1/16W R806 1-218-957-11 RES,CHIP 2.2K 1/16W R864 1-218-953-11 RES,CHIP 1/16W R807 1-218-959-11 RES,CHIP 3.3K 1/16W R865 1-218-953-11 RES,CHIP 1/16W...
Page 206 VC-213 VF-126 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R922 1-218-973-11 RES,CHIP 1/16W < VIBERATOR > R923 1-218-943-11 RES,CHIP 1/16W R924 1-218-945-11 RES,CHIP 1/16W X251 1-760-320-11 VIBRATOR, CRYSTAL (28.6363MHz) R930 1-218-990-11 SHORT (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) R931 1-218-977-11 RES,CHIP 100K 1/16W X251...
Page 207 VF-126 VF-129 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C4622 1-162-970-11 CERAMIC CHIP 0.01uF R4521 1-216-809-11 METAL CHIP 1/16W C4623 1-109-982-11 CERAMIC CHIP R4524 1-218-907-11 RES,CHIP 330K 0.50% 1/16W C4626 1-107-682-11 CERAMIC CHIP R4525 1-218-877-11 RES,CHIP 0.50% 1/16W C4801 1-162-970-11 CERAMIC CHIP...
Page 208 VF-129 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks ! C911 1-164-715-11 CERAMIC CHIP 0.0068uF 5% R927 1-216-821-11 METAL CHIP 1/16W C912 1-107-854-11 TANTAL. CHIP 68uF 6.3V R928 1-216-827-11 METAL CHIP 3.3K 1/16W C913 1-135-145-11 TANTALUM CHIP 0.47uF R929 1-216-821-11 METAL CHIP 1/16W...
Page 209 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1-790-412-11 CABLE, FLEXIBLE FLAT (FFC-256) ACCESSORIES (EXCEPT:TRV315/TR7000/TR7000E/TR7100E) *********** 1-672-662-11 FP-47 FLEXIBLE BOARD (TRV315/TR7000/TR7000E/TR7100E) 1-475-141-61 REMOTE COMMANDER RMT-814 1-758-155-21 FILTER BLOCK, OPTICAL 1-475-599-11 ADAPTOR, AC (TRV110E/TRV210E/TRV310E/TR7000E/TR7100E) 1-569-007-11 ADAPTOR, CONVERSION 2P 1-758-216-21 FILTER BLOCK, OPTICAL (TRV110:JE/TRV310:JE/TRV310E:JE) (EXCEPT:TRV110E/TRV210E/TRV310E/TR7000E/TR7100E)
Page 210 Ref. No. Part No. Description Remarks 3-865-968-31 MANUAL, INSTRUCTION (GERMAN/ITALIAN) (TR7000E:AEP/TR7100E) 3-865-968-41 MANUAL, INSTRUCTION (DUTCH/FRENCH) (TR7000E:AEP/TR7100E) 3-865-969-01 MANUAL, INSTRUCTION (ENGLISH)(TR7000) 3-865-969-21 MANUAL, INSTRUCTION (FRENCH) (TR7000:CND) 3-865-970-11 MANUAL, INSTRUCTION(ENGLISH/RUSSIAN) (TRV110E:EE,NE,RU) 3-865-970-21 MANUAL, INSTRUCTION (SPANISH/PORTUGUESE)(TRV110E:AEP1) 3-865-970-31 MANUAL, INSTRUCTION (DUTCH/ITALIAN) (TRV110E:AEP2) 3-865-970-41 MANUAL, INSTRUCTION (ENGLISH/DUTCH) (TRV110E:AEP,UK) 3-865-970-51 MANUAL, INSTRUCTION (SWEDISH/POLISH) (TRV110E:EE,NE,RU)
Page 211 〈PARTS REFERENCE SHEET〉 You can find the parts position of location of mount locations applying to VC-213 board of a set. VC-213 DCR-TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 SIDE A DCR-TR7000/TR7000E/TR7100E IC801 IC760 — 322 —...
Page 212 〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC 720H model Take a copy of CAMERA COLOR DCR-TRV103/TRV110/TRV110P/TRV203/ REPRODUCTION FRAME and TRV210/TRV310/TRV310P/TRV315 Parts referencesheets with a clear DCR-TR7000 sheet for use. For PAL 960H model DCR-TRV110E/TRV210E/TRV310E DCR-TR7000E/TR7100E — 323 —...
Page 213 DCR- TRV103/TRV110/TRV110E/TRV110P/TRV203/TRV210/ TRV210E/TRV310/TRV310E/TRV310P/TRV315 DCR- TR7000/TR7000E/TR7100E Sony Corporation 99B1636-1 Printed in Japan ©1999.2 Personal A&V Products Company 9-974-147-11 Published by Quality Engineering Dept. — 324 — (Shinagawa)

This manual is also suitable for:

Dcr-trv110 Dcr-trv210 Dcr-trv210e Dcr-trv310 Dcr-trv310e Dcr-trv310p ... Show all

Sony DCR-TRV103 Service Manual

Table of Contents

Related Manuals for Sony DCR-TRV103

Summary of Contents for Sony DCR-TRV103

This manual is also suitable for:

Table of Contents