Video: 1 Vp-p 75 ohms Output Video: 1 Vp-p 75 ohms General Power requirements AVD-S50ES: 120 V AC, 60 Hz AVD-S50: 230 V AC, 50/60 Hz Power consumption 180 W 1.5 W (at the Power Saving Mode) Dimensions (approx.) 430 × 98 × 453 mm (17 × 3 ×...
Page 3
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
AVD-S50/S50ES Ver 1.4 SECTION 1 SERVICING NOTES LASER DIODE AND FOCUS SEARCH OPERATION NOTES ON HANDLING THE OPTICAL PICK-UP CHECK BLOCK OR BASE UNIT Carry out the “S curve check” in “DVD section adjustment” and The laser diode in the optical pick-up block may suffer electro- check that the S curve waveforms is output three times.
AVD-S50/S50ES SECTION 3 DISASSEMBLY Note: This set can be disassemble according to the following sequence. 3-1. CASE (Page 10) 3-2. LOADING PANEL ASSY 3-4. BACK PANEL ASSY, (Page 11) POWER SW BOARD (Page 12) 3-3. FRONT PANEL ASSY (Page 11) 3-5.
AVD-S50/S50ES 3-2. LOADING PANEL ASSY loading panel assy 1 tapering driver 4 loading panel assy Note: When the power supply does not turn on, 3 two claws rotate the cam with tepering driver ( ∅ 3 mm) as the figure shows, –...
AVD-S50/S50ES Ver 1.4 SECTION 4 TEST MODE [GENERAL DESCRIPTION] 0-0. Quit Quit the Syscon Diagnosis and return to the Test Mode Menu. The Test Mode allows you to make diagnosis and adjustment easily using the remote commander and monitor TV. The instructions, 0-1.
Page 16
0-2-4. Model Type discs. Also, do not give a shock during adjustment. Model name is displayed. (AVD-S50 or AVD-S50ES) 1-1. DVD-SL (single layer) 0-2-5. Region Press the [1] key on the remote commander and insert a DVD single Model destination code is displayed.
Page 17
AVD-S50/S50ES Ver 1.4 12. Tracking on 38. EQ boost adjust 13. (TC display start) 39. Auto Loop Filter Offset 14. Wait 1 sec 40. Auto track gain adjust 15. Jitter display start Search Check 16. Sled ON 41. 32 track jump forward 17.
Page 18
AVD-S50/S50ES 2-1. Disc Type 2-1-3. Disc Type CD It sets up so that it may judge as a disc type of specification of the disc with which the set was inserted. Disc Type : CD disc (normal speed, 12 cm)
Page 20
AVD-S50/S50ES 2-7. Disc Check Memory MECHA AGING On the Test Mode Menu screen, selecting executes the aging of Disc Check Memory the mechanism deck. 1. SL Disc check 2. CD Disc check ### Aging Test MENU ### 3. DL Disc check Operation Menu 1.
Page 21
AVD-S50/S50ES Ver 1.2 • Code list of Emergency History 50 : Disc eject failing in the midst of initializing the mechanism 10: Communication to RF AMP (IC001) failed. deck. 11: Each servo for focus, tracking, and spindle is unlocked. 5x : Initializing the mechanism deck.
AVD-S50/S50ES SECTION 5 DIAGRAMS 5-1. IC PIN FUNCTION DESCRIPTION • DVD BOARD IC301 CXP973064-233R (MECHANISM CONTROLLER) Pin No. Pin Name Pin Description EEP SO Not used. (Open) SDEN Serial data enable signal output to DVD/CD RF amplifier DOCTRL/ Digital out on/off contrrol signal output to the digital signal processor ISBTEST “L”: digital out off, “H”: digital out on...
Page 23
AVD-S50/S50ES Pin No. Pin Name Pin Description MUTE DSD Muting on/off control signal output to the DSD decoder “H”: muting on SQCK Subcode Q data reading clock signal output to the digital signal processor — Ground terminal (digital system) TRAY IN Disc tray in detection signal input terminal Not used.
Page 24
AVD-S50/S50ES • DVD BOARD IC401 CXD3068Q (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR) Pin No. Pin Name Pin Description DVDD0 — Power supply terminal (+3.3 V) (digital system) XRST Reset signal input from the mechanism controller “L”: reset MUTE Muting on/off control signal input from the mechanism controller “H”: muting on...
Page 25
AVD-S50/S50ES Pin No. Pin Name Pin Description AVDD0 — Power supply terminal (+3.3 V) (analog system) ASYO EFM full-swing output terminal ASYI Asymmetry comparator voltage input terminal RFAC EFM signal input from the DVD/CD RF amplifier AVSS1 — Ground terminal (analog system)
Page 26
AVD-S50/S50ES • DVD BOARD IC607 CXD9617R (AUDIO DIGITAL SIGNAL PROCESSOR) Pin No. Pin Name Pin Description — Ground terminal XRST Reset signal input from the system controller “L”: reset EXTIN Master clock signal input terminal Not used. (Fixed at “L” in this set.) Sampling frequency selection signal input terminal Not used.
Page 27
AVD-S50/S50ES Pin No. Pin Name Pin Description VDDE — Power supply terminal (+3.3 V) WMD1 S-RAM wait mode setting terminal Fixed at “H” in this set — Ground terminal WMD0 S-RAM wait mode setting terminal Fixed at “L” in this set PAGE2 Page selection signal output terminal Not used.
Page 28
AVD-S50/S50ES Pin No. Pin Name Pin Description SDI4 Audio serial data input terminal Not used. (Fixed at “L” in this set.) Synchronous/asynchronous selection signal input terminal SYNC “L”: synchronous, “H”: asynchronous (fixed at “H” in this set) 117 to 119 —...
Page 29
AVD-S50/S50ES • DVD BOARD IC701 CXD1882R (DVD DECODER) Pin No. Pin Name Pin Description 1, 2 D5, D6 Two-way data bus with the mechanism controller — Ground terminal (digital system) Two-way data bus with the mechanism controller Address signal input from the mechanism controller —...
Page 30
AVD-S50/S50ES Pin No. Pin Name Pin Description DVD mode: Serial data request signal input from the DVD system processor XSRQ SACD mode: Serial data request signal input from the DSD decoder HINT Not used. (Fixed at “H” in this set.) XS16 Not used.
Page 31
AVD-S50/S50ES Pin No. Pin Name Pin Description RFDCC Input terminal for adjusting DC cut high-pass filter for RF signal RFIN RF signal input from the DVD/CD RF amplifier 118, 119 VCCA5, VCCA4 — Power supply terminal (+3.3 V) (analog system) VCOR1 —...
Page 32
AVD-S50/S50ES Pin No. Pin Name Pin Description XTAL 33.8688 MHz clock signal input terminal — Ground terminal (digital system) XTL2 System clock output terminal (33.8688 MHz) XTL1 System clock input terminal (33.8688 MHz) — Power supply terminal (+3.3 V) (digital system)
Page 33
AVD-S50/S50ES • DVD BOARD IC801 CXD2752R (DSD DECODER) Pin No. Pin Name Pin Description VSCA0 — Ground terminal (for core) XMSLAT Serial data latch pulse signal input from the mechanism controller MSCK Serial data transfer clock signal input from the mechanism controller...
Page 34
AVD-S50/S50ES Pin No. Pin Name Pin Description PHREFI Bit clock signal (2.8224 MHz) input terminal for DSD data output Not used. (Open) PHREFO Bit clock signal (2.8224 MHz) output to the digital audio processor ZDFL Front L-ch Zero data flag detection signal output terminal Not used. (Open)
Page 35
AVD-S50/S50ES Pin No. Pin Name Pin Description WRFD Not used. (Fixed at “L” in this set.) Operation clock signal input for PSP physical disc mark detection from the DVD decoder 124, 125 WAVDD0, WAVDD1 — A/D power supply terminal (+2.5 V) (for PSP physical disc mark detection)
Page 36
AVD-S50/S50ES • DVD BOARD IC901 µPD703033BYGF-M03-3BA (SYSTEM CONTROLLER) Pin No. Pin Name Pin Description DAMP-DATA Serial data output to the stream processors DAMP-CLK Serial data transfer clock signal output to the stream processors I2C-DATA Communication data bus with the DVD system processor and mechanism controller CQ-RST Reset signal output to the DVD system processor “L”: reset...
Page 37
AVD-S50/S50ES Pin No. Pin Name Pin Description DRI-RST Reset signal output to the power amplifier “L”: reset DRI-OCP Protect signal input from the power amplifier ST-POWER System power on/off control signal output “H”: power on HP-MUTE Headphone muting on/off control signal output “L”: muting on Not used. (Open) AU-MUTE Audio line muting on/off control signal output “L”: muting on...
Page 38
AVD-S50/S50ES Pin No. Pin Name Pin Description POWER-SW System power on/off control signal input “H”: power on SIRCS Remote control signal input System wake up signal input by pressing any key on the front panel or remote WAKE commander or disc insert detect sensor...
Page 39
AVD-S50/S50ES • DVD BOARD IC902 PT8300 (CHANGER CONTROLLER (MOTOR, SWITCH)) Pin No. Pin Name Pin Description — Ground terminal RESET B Reset signal input from the system controller “L”: reset Serial data transfer clock signal input from the system controller...
AVD-S50/S50ES 5-2. CIRCUIT BOARDS LOCATION 5-3. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. SP board DIGITAL AMP board (In addition to this, the necessary note is printed in each block.)
AVD-S50/S50ES 5-12. SCHEMATIC DIAGRAM — DVD SECTION (6/10) — • Refer to page 76 for IC Block Diagram. CL801 IC202 C253 C254 C258 C217 C219 C257 FL202 C226 FL203 FORMER TYPE C234 NEW TYPE IC205 C238 IC204 C239 R251 R213...
Page 80
AVD-S50/S50ES IC902 STR-F6238S (POWER Board) (US, CND Model) IC902 STR-F6270D (POWER Board) (AEP, UK Model) DRIVE REGULATOR OVER CURRENT PROTECTOR OVER INH1 VOLTAGE START PROTECTOR LATCH THERMAL SHUT DOWN FEED BACK INH2 OVER LOAD PROTECTOR REGULATOR DRIVE CURRENT MIRROR IC904 SI-8050JF (POWER Board)
AVD-S50/S50ES Ver 1.3 SECTION 6 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied.
AVD-S50/S50ES 6-3. CHASSIS SECTION not supplied CDM66D-DVBU15 F901 not supplied not supplied not supplied not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety.
AVD-S50/S50ES 6-4. BACK PANEL SECTION FAN961 not supplied not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une piéce...
AVD-S50/S50ES 6-6. BASE UNIT SECTION (DVBU15) The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une piéce specified.
AVD-S50/S50ES SECTION 7 ANALOG I/O ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
Page 88
AVD-S50/S50ES ANALOG I/O DIGITAL AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R620 1-216-845-11 METAL CHIP 100K 1/10W A-4729-236-A DIGITAL AMP BOARD, COMPLETE (AEP,UK) R621 1-216-833-11 METAL CHIP 1/10W A-4729-252-A DIGITAL AMP BOARD, COMPLETE (US,CND)
Page 91
AVD-S50/S50ES DIGITAL AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark IC324 8-759-711-85 IC NJM4580E-D R306 1-216-810-11 METAL CHIP 1/10W IC325 8-759-271-88 IC TC7SHU04FU R307 1-216-797-11 METAL CHIP 1/10W IC326 8-759-679-05 IC TC7WH34FU(TE12R) R308 1-216-797-11 METAL CHIP...
Page 92
AVD-S50/S50ES DIGITAL AMP DIGITAL I/O Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R372 1-216-810-11 METAL CHIP 1/10W R452 1-216-813-11 METAL CHIP 1/10W R373 1-216-797-11 METAL CHIP 1/10W R453 1-216-811-11 METAL CHIP 1/10W R374 1-216-797-11 METAL CHIP...
Page 93
AVD-S50/S50ES DIGITAL I/O DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > D873 8-719-041-97 DIODE MA113-(TX) D874 8-719-041-97 DIODE MA113-(TX) IC650 8-759-533-85 IC L88M05T-FA-TL D875 8-719-977-28 DIODE DTZ10B IC651 8-749-017-31 IC GP1FA550TZ (OPTICAL OUT)
Page 113
AVD-S50/S50ES US Model Canadian Model SERVICE MANUAL AVD-S50ES AEP Model UK Model Ver 1.1 2002. 09 AVD-S50 SUPPLEMENT-1 File this supplement with the service manual. Subject : Addition of Block Diagrams. 9-874-154-81...
Page 117
AVD-S50/S50ES 3. BLOCK DIAGRAM — AUDIO OUT, PANEL SECTION — D/A CONVERTER HP AMP IC608 IC321 • SIGNAL PATH R-CH J900 RY301 PHONES 3 SDTI AOUTL+ : AUDIO J601 (1/2) AOUTL– LOW-PASS HP PRE AMP VIDEO 1 1 MCLK FILTER...
Page 118
AVD-S50/S50ES 4. BLOCK DIAGRAM — VIDEO SECTION — AEP,UK ONLY J762 RY761 V IN R/CR RELAY US,CND ONLY V/Y OUT V OUT DRIVE B/CB IC761 Q761 R/C OUT SD0 – SD7 (Page 3) AV DATA BUS VDAC_0 J704 R/C OUT...
Page 121
AVD-S50/S50ES US Model Canadian Model SERVICE MANUAL AVD-S50ES AEP Model UK Model Ver 1.4 2004. 09 AVD-S50 SUPPLEMENT-2 File this supplement with the service manual. Subject : Addition of Electrical Adjustments. ELECTRICAL ADJUSTMENTS Procedure: 1. Connect an oscilloscope to test point 1 pin and 3 pin of CN901 Note: 1.
Page 122
AVD-S50/S50ES REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2002. 08 2002.