Related Manuals for Kenwood KDC-C519FM
Summary of Contents for Kenwood KDC-C519FM
-
Page 1: Instruction Manual
KDC-C519FM CD AUTOCHANGER / CONTROLLER / FM MODULATOR SYSTEM INSTRUCTION MANUAL COMPACT DIGITAL AUDIO ©B64-2352-00/00 (MW) -
Page 2: Table Of Contents
Contents Before use Safety Precautions ...3 Handling Compact Discs ...5 Loading Compact Discs ...6 Buttons Display Unit ...7 Remote ...7 Operations Playing CDs ...7 Fast Fowarding and Reversing Disc Play ...8 Track Search...8 Disc Search ...8 Direct Track Search ...8 Direct Disc Search...9 Track Repeat ...9 Disc Repeat...9... -
Page 3: Safety Precautions
• The reception of the tuner may be reduced a little if the KDC-C519FM is used. • If the sound is lower than the tuner sound, raise up the volume level of the CD with using the receiver. - Page 4 Safety Precautions 2CAUTION Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries: Use two "AAA" batteries. Slide the cover while pressing downwards to remove it as illustrated. – Insert the batteries with the poles aligned properly, following the illustration inside the case.
-
Page 5: Handling Compact Discs
Handling Compact Discs Playing a CD that is dirty, scratched or warped can cause the sound to skip and the unit to operate incorrectly, resulting in worsened sound quality. Take the following precautions to prevent your CDs from getting scratched or damaged. Handling CDs •... -
Page 6: Loading Compact Discs
Loading Compact Discs "KENWOOD" Projection Make sure the disc magazine is the right way up with the Kenwood logo on the top.Pull the tray out by the projection. Place the disc on the tray with the label facing upwards. Insert the tray into the disc magazine until it locks. -
Page 7: Buttons Display Unit
Buttons Display Unit C D A U T O C H A N G E R C O N T R O L L E R T R A C K T R A C K FREQ LEVEL M . R D M D . -
Page 8: Fast Fowarding And Reversing Disc Play
Operations Fast Forwarding and Reversing Disc Play Fast Forwarding Disc Play : Hold down on the ¢ button. Release your finger to play the disc at that point. Reversing Disc Play : Hold down on the 4 button. Release your finger to play the disc at the point. Track Search Search forward or backward through the tracks on the disc until you reach the one that you want to listen to. -
Page 9: Direct Disc Search
Direct Disc Search Using the remote, directly input the disc number that you want to listen to. Using the number buttons on the remote, input the number of the disc that you want to listen to. The selected disc number will blink in the display for 10 seconds. -
Page 10: Random Play
Operations Random Play Play all the tracks on the current disc in random order. Press the RDM button to switch the random play function on and off. The RDM indicator lights up when the random play function is turned on. The display of the track number changes continuously as the next track is being selected. -
Page 11: Changing The Transmission Frequency
Changing the transmission frequency To set the frequency change mode Press the REP button for at least three seconds. The FREQ indicator will light up and the currently set frequency will be displayed. F R E Q M H z NOTE •... -
Page 12: Modulation Level/Dynamic Control
Operations Modulation level / Dynamic control To set the control mode Press the RDM button on the display unit for at least three seconds. The LEVEL indicator will light up and the currently set modulation level will be displayed. Modulation level L E V E L Number for prevention of distortion setting... -
Page 13: Accessories
Accessories External view ... Number of items ...1 ...4 ...4 ...1 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. Installation Procedure 1. -
Page 14: Connecting Wires To Terminals
Installation Procedure ■ Angle adjustment switches The angle adjustment switches on the both saides of the unit are to be set according to the angle of installation of the CD auto changer. Set both of the two switches to the same position. -
Page 15: Installation
Installation ■ Horizontal installation Use the holes marked (¶) to install the unit. Side view ■ Vertical installation Use the holes marked (¶) to install the unit. Side view ■ In case of hanging in the trunk Use the holes marked (¶) to install the unit. Side view ø4 ■... - Page 16 Installation ■ Installation of Display unit • Installation without using the trim mount plate Display unit Attach one velcro to the slanted-line of the the display units as shown above, and attach the other velcro to the parts where you wish to attach the display units.
-
Page 17: Troubleshooting Guide
Troubleshooting guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM The power is not turned on. The wiring harness fuse blows. - Page 18 Troubleshooting guide PROBLEM Sound skips due to vibration. Something is touching the CD auto-changer. The disc is dirty or damaged. The unit is mounted at a slant. Changer unit is mounted in an unstable place. The angle adjustment switches are set improperly. Nothing appears on the display.
- Page 19 The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. 01 E: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. Load the disc magazine properly. 02 E: No disc has been loaded in the disc magazine..
-
Page 20: Specifications
Specifications Specifications subject to change without notice. Disc section Laser Diode...GaAlAs (λ=780 nm) Digital Filter (D/A) ...8 Times Over Sampling D/A Converter...1 bit Spindle speed ...500 ~ 200 rpm (CLV) Wow & Flutter ...Below Measurable Limit Frequency Response (±1 dB) ...10 Hz ~ 20 kHz Modulating Frequency (200KHz STEP) ...87.7, 87.9, 88.1, 88.3, General Operating Voltage...14.4 V (11 ~ 16 V)