hit counter script
Sony SAL135F18Z Service Manual

Sony SAL135F18Z Service Manual

Lens for dslr camera (sonnar 1.8/135 za) (sonnar t* 135mm f1.8 za)
Hide thumbs Also See for SAL135F18Z:

Advertisement

SERVICE MANUAL
Ver. 1.4 2007.12
Revision History
Revision History
How to use
How to use
Acrobat Reader
Acrobat Reader
Revised-1
Replace the previously issued
SERVICE MANUAL 9-852-110-11
with this Manual.
Link
Link
SPECIFICATIONS
SERVICE NOTE
• About the Special Driver
• About the Lens Test Projector and Finished Inspection JIG
• About the Screw Filter Frame Assy.
• About the MTF measurement.
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
9-852-110-12
SAL135F18Z
(Sonnar 1.8/135 ZA) (Sonnar T
DISASSEMBLY
REPAIR PARTS LIST
135mm F1.8 ZA)
*
Sony EMCS Co.
135mm F1.8 ZA)
*
Canadian Model
Chinese Model
ADJUSTMENTS
LENS FOR DSLR CAMERA
US Model
AEP Model
2007L0800-1
© 2007.12
Published by Kohda TEC

Advertisement

Table of Contents
loading

Summary of Contents for Sony SAL135F18Z

  • Page 1 • About the Lens Test Projector and Finished Inspection JIG • About the Screw Filter Frame Assy. • About the MTF measurement. LENS FOR DSLR CAMERA 2007L0800-1 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) © 2007.12 Sony EMCS Co. 9-852-110-12...
  • Page 2: Specifications

    Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Lens case (1), Set of printed documentation Designs and specifications are subject to change without notice. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) — 2 —...
  • Page 3: Table Of Contents

    Focus Brush Position Check/Adjustment ····················· 4-30 4-9. Focus Hold Button Check (Focus Hold Button) ·········· 4-36 4-10. Focus Hold Button Check (Focus Hold Button Short) ··········································· 4-38 4-11. Write dSB ····································································· 4-41 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) — 3 —...
  • Page 4: Service Note

    • Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing unleaded solder and leaded solder will cause detachment phenomenon. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 5: Safety Check-Out

    CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
  • Page 6: Troubleshooting

    (See page 4-16.) Check operation of the preset ring, and replace Check operation the defective part. of the diaphragm control block. Replace the defective part. Perform the aperture diameter check. (See page 4-13.) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 7 Clean the pattern of the F-ECD flexible. Replace the defective part or apply the grease. Replace the F-ECD flexible. Check the operation again. Perform the focus brush position check/adjustment (See page. 4-30.) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 8: Disassembly

    Chip Chip Fixed screw Chip-B Holes When top of tip does not reach holes or notches because the fixed screw becomes obstructive, replace the fixed screw to below. +B 3X5 7-682-546-09 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 9 If removing or installing the parts of side of lens mount after the filter screw frame is removed, be careful to avoid damaging the 1 lens block. Note 3: Remove the screw (Ref. No. 15 or 61, 2-897-949-01 screw (3ULR-F M1.7x1.6(C3C))) using the special driver. Special driver: J-6082-654-A Shape of head SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 10 Carl Zeiss Serial No. is needed, and then you may obtain user’s agreement, and it replace. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 11 Install the 1 lens block placed with same position of removing it to the length grove barrel assy. * When removing the 1 lens block, put the marks of both the 1 lens block and length grove barrel assy. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 12 Aligning the inner cut portions at three locations with the guide pins, install the screw filter frame assy with the print of [1.8/135] placed at the distance scale window side. Screw Filter Frame Assy Inner Cut Portions Inner Cut Portions Guide Pins Guide Pin Distance Scale Window SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 13 Apply the adhesive bond (B-40) to the tip of three guide pins and tighten them. Guide Pins (Apply the adhesive bond (B-40)) Draw Ring Assy Guide Pins (Apply the adhesive bond (B-40)) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 14 Be careful not to drop screws in the lens. Confirm that the preset ring moves smoothly. Screw (Apply the adhesive bond (B-40)) Screws Light Shield Ring Block (Apply the adhesive bond (B-40)) Preset Ring SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 15 Install the contact flexible. Apply the adhesive bond (B-40) to the screwed portions of screws, and tighten two screws to fix the contact flexible. Note: Be careful not to drop screws in the lens. Screws (Apply the adhesive bond (B-40) Contact Flexible SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 16 After inserting the shaft of coupler in the cut portion of FB adjustment washer, install it to the lens. Note: • Place the golden FB adjustment washer on the side of mount. • Be careful not drop the coupler. Coupler FB Adjustment Washer FB Adjustment Washer (Gold) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 17 • After tightening the screws, confirm that the coupler rotates when the focus ring is rotated. Screws Screws (Apply the adhesive bond (Apply the adhesive bond (B-40)) (B-40)) Mount Block Holes for coupler installation Coupler Receive Coupler SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 18 Install the writing flexible of contact block to the contact board guide with two screws. Apply the adhesive bond (B-10) to the heads of screws. Screws (Apply the adhesive bond (B-10)) Install the writing flexible Contact Flexible Guide SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 19 Apply the adhesive bond (B-10) to the heads of screws. Confirm that the preset ring moves smoothly. Screws (Apply the adhesive bond (B-10)) Main Spring Guide Main Spring Preset Ring SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 20 Apply the adhesive bond to the outer diameter side of head of screws and be careful for the bond not to flow in the groove for preset ring. Screws Screws (Apply the adhesive bond (B-10)) (Apply the adhesive bond (B-10)) Index hole Rear Ring Assy Index pin SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 21 Apply the adhesive bond to the outer diameter side of head of screws and be careful for the bond not to flow in the groove for preset ring. Screws Screws (Apply the adhesive bond (B-10)) (Apply the adhesive bond (B-10)) Index hole Rear Ring Assy Index pin SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 22 Aligning four cut portions of preset ring with the bosses of rear ring assy at four locations, install the preset ring. Note: After installing the preset ring, confirm that the preset ring moves smoothly. Cut Portion Preset Ring Cut Portion Cut Portion Cut Portion Bosses Bosses Rear Ring Assy SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 23 Adjust the aperture diameter. (Refer to 4-2.) After adjust the aperture diameter, apply the adhesive bond (B-10) to the tip of screws. Screws Function Lever Oblong holes Iris Control Lever SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 24 • After connecting, confirm that the connector is securely locked. Screw (Apply the adhesive bond (B-10)) Contact Flexible Connector Main Flexible Screw (Apply the adhesive bond (B-10)) Connector FH Button Main Flexible F-ECD Flexible Focus Hold Barrel Block SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 25 Adhesive bond (B-10): J-6082-612-A Grease (G-35): J-6082-621-A Apply the grease (G-35) to the location shown in figure of length grove barrel assy. Length Grove Barrel Assy Apply the grease (G-35) (All round) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 26 Apply the adhesive bond (B-10) to the heads of nine screws. Perform the torque ring play adjustment. (Refer to 4-6.) Screw (Black) Apply the adhesive bond (B-10) Screw (White) Apply the adhesive bond (B-10) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 27 Length Grove Barrel Assy HELP14 Peel off the detached paper from the 2nd ornamental sheet and affix it to the location specified in figure. 2nd Ornamental Sheet 2 Lens Block SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 28 After finishing the position adjustment, apply the adhesive bond (B-10) to the location of screwed portion shown in figure. Zoom Brush Pattern of F ECD Flexible Apply the adhesive bond (B-10) Screws Zoom Brush Focus 1 Cam Ring Assy SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 29 2 Roller Screw (Apply the adhesive bond (B-40) (3 places)) 2 Lens Block 2 Roller (3 places) Focus 1 Cam Ring Assy Confirm that the focus 1 cam ring assy rotates smoothly. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 30 (Apply the adhesive bond (B-40) (3 places)) Iris Control Lever 3 Roller (3 places) Iris Block Focus 1 Cam Ring Assy Confirm that the focus 1 cam ring assy rotates smoothly. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 31 (Apply the adhesive bond (B-40) (3 places) 3 Lens Block 3 Roller (3 places) Gear F-ECD Flexible Focus 2 Cam Ring Block Confirm that the focus cam 2 ring block rotates smoothly. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 32 Fix the focus scale with two screws. (Use the special driver: J-6082-654-A) Apply the adhesive bond (B-10) to the heads of screws. Pasted standard Vertical Pasted standard Horizontal Length Grove Barrel Assy Focus Scale Screws (Apply the adhesive bond (B-10)) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) HELP...
  • Page 33: Repair Parts List

    A-1226-230-A ASSY, PWB FLEXIBLE MAIN 2-886-787-01 COUPLER RECEIVE 2-898-117-01 SCREW (2P 1.7X2.2 BNI) 2-898-017-01 BLOCK, MOUNT A-1224-099-A RING ASSY, REAR 2-898-020-01 RING BLOCK, LIGHT SHIELD 2-695-839-01 LABEL, MODEL NAME 2-898-024-01 SCREW (2P 1.4X2.2 BNI) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 34 Selection parts ROLLER (A, D), 3 (Note 1) 2-897-950-01 SCREW (HEXAGONAL M2X5.5 C3C) 2-897-898-01 SCREW, ROLLER 3 X-2177-204-1 LENGTH GROVE BARREL ASSY (Note 2) 2-897-972-01 SHEET, SCALE FOCUS 2-897-949-01 SCREW (3ULR-F M1.7X1.6 C3C) (Note 3) 2-897-971-01 BRUSH, ZOOM SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 35 2-897-852-01 WASHER, TILT ADJUSTMENT D (t=0.1) Part No. Description 2-897-899-01 ROLLER, 3 A (D1=3.99,D2=4.50,D3=3.48) 2-897-900-01 ROLLER, 3 D (D1=3.99,D2=4.51,D3=3.48) 3-113-316-01 ROLLER, 3 K (D1=3.99,D2=4.51,D3=3.50) 3-113-317-01 ROLLER, 3 L (D1=3.99,D2=4.51,D3=3.52) 3-113-318-01 ROLLER, 3 M (D1=3.99,D2=4.51,D3=3.54) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 36: Supplied Accessories

    2-685-145-11 MANUAL, INSTRUCTION (GERMAN, DUTCH, SWEDISH, ITALIAN) (AEP) 2-685-145-21 MANUAL, INSTRUCTION (PORTUGUESE, RUSSIAN, ARABIC, TRADITIONAL CHINESE, KOREAN) (AEP) Lens Hood (SH0003) Front Lens Cap 2-687-326-01 X-2176-984-1 Rear Lens Cap Lens Case 2-683-615-01 2-694-834-01 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 37: Adjustments

    (D3LUF 88H) J-6082-655-A J-6082-654-A J-6082-645-A (Note 4) J-14 J-13 J-15 Chip-B for Chip-A for universal wrench Universal wrench universal wrench J-6082-609-2 J-6082-609-A J-6082-609-1 J-16 Filter screw frame removing tool J-6082-649-A Fig.4-1-1 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 38 Chart 1000 mm collimator Fig.4-1-2 Note 3: Connect the variable transformer (Output voltage: AC 100 V) to the lens test projector. Note 4: Finished Inspection JIG is AC 100 V only. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 39 Download the file from Service Fixture and Software of ESI homepage, and save it in “C:\MCC”. Double-click the downloaded file “InstaCal.zip”to extract it. [Browse...] The window to specify the extract destination folder appears. Click Fig.4-1-4 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 40 6) The window returns to the menu to specify the extract destination folder. Click Fig.4-1-6 7) When the window below appears, click [OK]. Fig.4-1-7 [Close] 8) Return to the menu to specify the extract destination folder. Then, click to close the window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 41 Double-click “InstaCal.msi” in “C:\MCC” folder to begin the installation. Fig.4-1-8 [Next>] The menu to begin the installation appears. Click Fig.4-1-9 [Next>] Specify the install destination folder. As the default is used for it, click Fig.4-1-10 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 42 6) To make the configuration installed effective, the window to prompt the restart appears. Click “Yes” to restart the PC. Note: If a device is connected without restarting, the program may not work properly. Fig.4-1-13 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 43 After restarting the PC, insert the PC-CARD-DIO48 in the PC card slot. The software installation window appears. Click “Install the software automatically. (Recommended)”. Fig.4-1-14 [Finish] The software is detected and installed. When the window below appears, click to terminate the installation. Fig.4-1-15 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 44 Depending on the slot inserted, the slot No. differs. Fig.4-1-17 3) Confirm that “PC-CARD-DIO48” is recognized as “Board#0”. Note: If not recognized as “Board#0”, the program does not work properly. Fig.4-1-18 4) Click “File” - “Exit” to terminate “InstaCal”. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 45 Download the file “ActuatorChecker VerX.X.X.X.zip” from Service Fixture and Software of ESI homepage, save and extract it. Start up “ActuatorChecker.exe” from an arbitrary folder. If “PC-CARD-DIO48” is properly installed, the window below appears. Note: The version of “ActuatorCheker” might be updated. Fig.4-1-19 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 46 Turn on the finished inspection JIG. Turn on the personal computer. Start up “ActuatorChecker.exe” from an arbitrary folder, conform that start up program normally. Note: Turn off the finished inspection jig after use. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-10...
  • Page 47 Depending on the initial startup or setting made at the previous startup, the window differs.When the English window appears, click [Set up] button. Note: When any button is clicked, the Serial window appears. The window to enter the lens serial number appears. Fig.4-1-22 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-11...
  • Page 48 The procedure for executing the inspection of each item one by one has been described in this manual. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 49: Aperture Diameter Check/Adjustment

    Setting of Luminance box: Luminance: EV12 Setting of Lens: Focus: Infinity end Setting of Camera: ISO: Exposure Mode: shutter Speed: 1/125 Aperture: F5.6 Focus Mode: Metering: Center weighted Preset white balance: Tungsten D-R: SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-13...
  • Page 50 Measured value display (Display menu): RGB+L*a*b* Measuring method (Display menu): Center Single Area Fig.4-2-4 Color space (Edit menu): sRGB Fig.4-2-5 Area size for calculate (Edit menu →Option): 256×256 Pixels Fig.4-2-6 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-14...
  • Page 51 Aperture error = Average “G” value of checking lens (b) - Average “G” value of master lens (a) Specification Aperture error = 0 ±12 When the aperture error is out of specification, perform “4-2-2. Aperture Diameter Adjustment”. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-15...
  • Page 52 • Adhesive bond (B-10): J-6082-612-A • Open JIG • Special driver 1. Preparation 1) Remove the light shield ring block and contact flexible. Light Shield Ring Block Contact Flexible Fig.4-2-8 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-16...
  • Page 53 Remove the mount block, FB adjustment washer and coupler. Mount Block FB Adjustment Washer Coupler FB Adjustment Washer (Gold) Fig.4-2-9 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-17...
  • Page 54 4) Move the preset lever to set preset ring at the open aperture position. 5) Two screws that are the fixation of the function lever in the preset ring are loosened. Open JIG Function Lever Screws Preset Ring Fig.4-2-10 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-18...
  • Page 55 Remove the light shield ring block, contact flexible and Open JIG. Attach the coupler, FB adjustment washer, contact flexible and light shield ring block, assemble the state of near completion. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-19...
  • Page 56: Projective Resolving Power Check

    Chart Chart Filament Filament f=18 to 35 mm f=100 to 200 mm Fixed lever Chart Chart Filament Filament f=35 to 100 mm f=200 to 300 mm Lens test projector Fig.4-3-1 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-20...
  • Page 57 Turn the focus ring of the checking lens until the chart image projected on the screen is the sharpest at the center (y’=0). Read the number of the smallest pitched lines at the center (y’= 0). The number represents for lines per mm. Saggital (S) Meridional (M) Fig.4-3-3 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-21...
  • Page 58 5) After the checking is completed, turn the lamp switch of the lens test projector to OFF and cool the inside of the lens test projector, then turn the fan switch to OFF. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 59: Flange Back (F'f) Check/Adjustment

    Turn the scale ring of the dial gauge until the long pointer indicates “0”. Note: This position is the flange back (f’F) = 43.50 mm. Memorize the position of short-pointer. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-23...
  • Page 60 (Infinity position) 44.90 to 44.94 Table 4-4-1 5) When the flange back (f’F) of the checking lens is out of specification of the Table 4-4-1, perform “4-4-2. Flange Back (f’F) Adjustment”. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-24...
  • Page 61 2-898-013-01 WASHER, FB ADJUSTMENT B 0.03 2-898-014-01 WASHER, FB ADJUSTMENT D 2-898-015-01 WASHER, FB ADJUSTMENT F Table 4-4-2 After replacing the FB adjustment washer, confirm that the specification is met. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-25...
  • Page 62: Focus-Shift Check/Adjustment (Aperture)

    • 1000 mm Collimator • Flange Back Tester • A-mount Attachment • Flange Back Gauge (43.50mm) • Aberration measuring cap 77mm (SAL135F18Z) 1. Preparations 1) Perform “1. Preparations” of “4-4-1. Flange Back (f’F) Check”. 2) Set the checking lens focus to the infinite.
  • Page 63: Torque Ring Play Adjustment

    Adjustment Procedure If the above adjustment condition is not met, adjust the eccentric pins at three locations. Torque Ring Eccentric Pin Distance Display Window Coupler Fig.4-6-1 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-27...
  • Page 64: Lens Rom Check

    2) The Serial window appears. Input the lens serial number. [OK] Note: When is clicked without inputting the serial number, the date executed is displayed on the completion window of each item. Fig.4-7-2 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-28...
  • Page 65 • Cleaning of flexible pattern or the brush. • Replaceing the brush. • Replaceing the main flexible unit. Perform “2. Checking Method” again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-29...
  • Page 66: Focus Brush Position Check/Adjustment

    4) If not adjusted in step 3), loosen two screws fixing the brush (For focus ring), and adjust the brush position, perform step 2) and 3) again. 5) After adjustment, apply the adhesive bond (B-10) to portions shown in Fig.4-8-1. 6) After adjustment, perform the [2 Focus Brush Position Check] and [3 Pattern Check]. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-30...
  • Page 67 The message “Move FOCUS to Near position. Then push [ENTER].” is displayed on the pop-up window. Set the focus to the near position and press down the ENTER key. Fig.4-8-5 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-31...
  • Page 68 • 4-8-1. Focus Brush Position Adjustment • Cleaning of flexible pattern or the brush. • Replaceing the brush. 3) Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-32...
  • Page 69 The message “Move FOCUS to Infinity position. Then push [ENTER].” is displayed on the pop-up window. Set the focus to the infinity position and press down the ENTER key. Fig.4-8-14 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-33...
  • Page 70 • Rotating operation error of the focus ring (rotation speed is not suitable at a regulated speed.). 3) Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 71 Fig.4-8-20 Fig.4-8-21 • When the lens does not reach the infinity end infinity position seconds. Fig.4-8-22 Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-35...
  • Page 72: Focus Hold Button Check (Focus Hold Button)

    3) The message “Push [FOCUS HOLD] button once softly.” is displayed on the pop-up window. Press the focus hold button. Fig.4-9-3 4) When the focus hold button check finishes normally, “OK” is displayed on the pop-up window. Fig.4-9-4 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-36...
  • Page 73 Although the button is pressed within a certain period of time, if the error occurs, replace the focus hold barrel block. Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 74 3) The message “Move FOCUS to Near position. Then push [ENTER].” is displayed on the pop-up window. Set the focus to the near position and press down the ENTER key. Fig.4-10-3 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-38...
  • Page 75 • Rotating operation error of the focus ring (rotation speed is not suitable at a regulated speed.). Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)
  • Page 76 5 seconds and no more than 10 seconds. Fig.4-10-8 Fig.4-10-9 2) Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-40...
  • Page 77: Write Dsb

    Being based on the image point shift amount calculated by “4-5. FOCUS-SHIFT CHECK/ADJUSTMENT (APERTURE)”, select the button. Fig.4-11-3 When the Write dSB finishes normally, “OK” appears on the pop-up window. Fig.4-11-4 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-41...
  • Page 78 • Replaceing the main flexible unit. • Connected state of equipment (Improper connection of BL error.). 3) Perform “2. Checking Method”again, repeat the inspection until “OK” appears on the pop-up window. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) 4-42...
  • Page 79 Cut the polyester tape (black) 10mm (per roll) (Ref. No. 25) for specified size. Ref. No. Part No. Description 9-913-210-03 POLYESTER TAPE (BLACK) 10mm (Note 4) 2007L0800-1 SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) © 2007.12 Sony EMCS Co. 9-852-110-82 Published by Kohda TEC...
  • Page 80 Guide Pin Distance Scale Window Push the filter screw frame removing tool to the draw ring assy and rotate it counterclockwise as far as it goes and stops. SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA) — 2 —...
  • Page 81 [Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once • To reverse the previous screens (operation) one by one, click 1. Click the Print button 2.
  • Page 82 • Change of HELP (HELP02) • Addition of guide [About the MTF mea- surement] (Cover, Page 1-2) • Correction of Aperture Diameter Check (Page 4-13, 4-15) • Correction of Formula of Focus-Shift (Page 4-26) SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T 135mm F1.8 ZA)

Table of Contents