Page 6
Automatic configuration and power interface (ACPI) BIOS . Automatic Power-On features . Recovering software using the Rescue and Recovery program . Starting the Rescue and Recovery workspace Hardware Maintenance Manual Appendix. Notices ..155 .
It is intended only for trained servicers who are familiar with Lenovo Before servicing a Lenovo product, be sure to read the Safety Information. See Chapter 2, “Safety information,” on page 5. The Symptom-to-FRU Index and Additional Service Information chapters are not specific to any machine type and are applicable to all ThinkCentre computers.
Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, PC...
Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under System Details. v Authorized Lenovo Business Partners can access Eclaim at the following Web site: http://wca.eclaim.com...
Page 10
Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant parts.
Page 12
CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed otherwise in the installation and configuration procedures.
v Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror.
5. Check for any obvious alterations. Use good judgment as to the safety of any alterations. 6. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 7.
Safety notices (multi-lingual translations) The caution and danger safety notices in this section are provided in the following languages: v English v Arabic v Brazilian/Portuguese v Chinese (simplified) v Chinese (traditional) v French v German v Hebrew v Italian v Korean v Spanish DANGER Electrical current from power, telephone and communication cables is hazardous.
Page 16
CAUTION: When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
Page 17
CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Page 20
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) Hardware Maintenance Manual...
Page 21
PERIGO A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. v Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas.
Page 22
CUIDADO: Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça 33F8354 ou um tipo de bateria equivalente recomendado pelo Se o seu sistema possui um módulo com uma bateria de lítio, substitua-o apenas por um módulo do mesmo tipo e do mesmo fabricante.
Page 23
CUIDADO: O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação estejam desconectados da fonte de alimentação.
Page 29
DANGER Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : v Ne manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de ce produit au cours d’un orage. v Branchez tous les cordons d’alimentation sur un socle de prise de courant correctement câblé...
Page 30
ATTENTION: Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
Page 31
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENTION: Soulevez la machine avec précaution. ATTENTION: L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre, le système peut être équipé de plusieurs cordonsd’alimentation. Pour mettre l’unité...
Page 32
VORSICHT An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen. Aus Sicherheitsgründen: v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen. v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß...
Page 33
CAUTION: Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer 33F8354 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen. Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein Modul desselben Typs und von demselben Hersteller ersetzen. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung explodieren.
Page 34
≥18 kg ≥32 kg ≥55 kg ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit vollständig zu unterbrechen, müssen alle zum Gerät führenden Netzkabel vom Netz getrennt werden.
Page 38
PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. v Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a terra.
Page 39
ATTENZIONE: Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 33F8354 o un tipo di batteria equivalente consigliato dal produttore. Se sul sistema è presente un modulo che contiene una batteria al litio, sostituirlo solo con un tipo di modulo dello stesso tipo della stessa casa di produzione.
Page 40
≥18 kg ≥32 kg ≥55 kg ATTENZIONE: Prestare attenzione nel sollevare l’apparecchiatura. ATTENZIONE: Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’ possibile che l’unità disponga di più cavi di alimentazione. Per disattivare l’alimentazione dall’unità, accertarsi che tutti i cavi di alimentazione siano scollegati dalla fonte di alimentazione.
Page 44
PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: v No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica.
Page 45
PRECAUCIÓN: Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 33F8354 u otra de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
Page 46
≥18 kg ≥32 kg ≥55 kg PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo. PRECAUCIÓN: El botón de control de alimentación del dispositivo y el interruptor de alimentación de la fuente de alimentación no desconectan la corriente eléctrica suministrada al dispositivo. Además, el dispositivo podría tener más de un cable de alimentación.
Specifications This section lists the physical specifications for your computer. Dimensions Height: 89 mm (3.5 in.) Width: 276 mm (10.9 in.) Depth: 273 mm (10.7 in) Weight Minimum configuration as shipped: 6.0 kg (13.2 lb) Maximum configuration: 6.4 kg (14.0 lb) Environment Air temperature: Operating at 0 - 3000 ft (914.4 m): 10°...
d. Observe the LEDs and refer to the following table. Green Power LED diagnostic LED OFF (after the power button has been pressed) If the Diagnostic LEDs are in the normal condition and the problem persists, replace the system board and the microprocessor, one at a time, until the computer works correctly.
Page 51
1. Are the exact machine type and models 2. Have the same BIOS level 3. Have the same adapters/attachments in the same locations 4. Have the same address jumpers/terminators/cabling 5. Have the same software versions and levels 6. Have the same Diagnostics Diskette (version) 7.
CD-ROM image (.iso file) of the diagnostics. To download the latest diagnostics program from the WWW, do the following: v Go to http://www.lenovo.com/think/support. v Type the machine type in the ″Use Quick Path″ field and click Go. v Click Downloads and drivers and scroll down to locate the Enhanced diagnostics.
Test selection To select one or more tests, use the following procedure. 1. Open the corresponding test category. 2. Using the cursor movement keys, highlight the desired test. 3. Press the space bar. A selected test is marked by >>. Pressing the space bar again de-selects a test and removes the >>.
Page 56
available for test, what tests are available for the device, device properties, and so on. To change testing parameters, you modify the FDAT.INI file in PC Doctor for DOS. FDAT consists of the following subtests and features. Fixed-Disk Tests: v Seek Tests: - checks the physical operation of the drive head. –...
channel buffer must be kept high in order to maintain a speed advantage over other data transfer modes. In order to use the UDMA channel during testing, users must disable the multitasking feature. Destructive versus non-destructive testing: Most of the tests found in FDAT are non-destructive. This means that PC-Doctor program will preserve any data that is present on the tested media prior to beginning any destructive operations (such as write operations).
The Full Erase Hard Drive provides a DOS utility that performs the following: v Performs all the steps in Quick Erase. v Provides a DOS utility that writes random data to all sectors of the hard drive. v Provides an estimate of time to completion along with a visual representation of completion status.
Password considerations If you are setting any of the various types of passwords on your computer, you should read and understand the following information: v If you type an incorrect password, you will see an error message. If you type an incorrect password three consecutive times, you must turn the computer off and start again.
Attention Make sure that the IDE Drive Master password is stored in a safe place. If both the IDE Drive User password and the IDE Drive Master password are lost or forgotten, the IDE hard disk drive must be replaced. If both the IDE Drive User Password and the IDE Drive Master Password are to be set, the IDE Drive Master Password must be set before setting the IDE Drive User Password.
Selecting a startup device If the computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to startup from any boot device.
Page 64
1. Turn off the computer and disconnect all external devices. 2. Power-on the computer. 3. There are three LEDs to help you determine if the power supply and system board are working correctly. The power button LED is located on the front of the computer and the two diagnostic LEDs are located on the power supply at the rear of the computer.
Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See “Running diagnostics tests” on page 48 for the specific type for information about the Diagnostic programs. In the following index, X can represent any number. Diagnostic Error Code 000-000-XXX BIOS Test Passed...
Page 66
Diagnostic Error Code 000-039-XXX BIOS DMI data error 000-195-XXX BIOS Test aborted by user 000-196-XXX BIOS test halt, error threshold exceeded 000-197-XXX BIOS test warning 000-198-XXX BIOS test aborted 000-199-XXX BIOS test failed, cause unknown 000-250-XXX BIOS APM failure 000-270-XXX BIOS ACPI failure 001-000-XXX System Test Passed...
Page 67
Diagnostic Error Code 001-027-XXX System Configuration/Setup error 001-032-XXX System Device Controller failure 001-034-XXX System Device Buffer Allocation failure 001-035-XXX System Device Reset condition detected 001-036-XXX System Register error 001-038-XXX System Extension failure 001-039-XXX System DMI data structure error 001-040-XXX System IRQ failure 001-041-XXX System DMA failure 001-195-XXX...
Page 68
Diagnostic Error Code 001-199-XXX System test failed, cause unknown 001-250-XXX System ECC error 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX System DMA error 001-260-XXX 001-264-XXX System IRQ error 001-268-XXX System IRQ1 failure 001-269-XXX System IRQ2 failure 001-270-XXX System IRQ3 failure 001-271-XXX System IRQ4 failure 001-272-XXX System IRQ5 failure 001-273-XXX...
Page 69
Diagnostic Error Code 001-281-XXX System IRQ14 (hard disk drive) failure 001-282-XXX System IRQ15 failure 001-286-XXX 001-287-XXX 001-288-XXX System Timer failure 001-292-XXX System CMOS RAM error 001-293-XXX System CMOS Battery 001-298-XXX System RTC date/time update failure 001-299-XXX System RTC periodic interrupt failure 001-300-XXX System RTC Alarm failure 001-301-XXX...
Page 70
Diagnostic Error Code 005-031-XXX Video Device Cable failure 005-032-XXX Video Device Controller failure 005-036-XXX Video Register error 005-038-XXX System BIOS extension failure 005-040-XXX Video IRQ failure 005-195-XXX Video Test aborted by user 005-196-XXX Video test halt, error threshold exceeded 005-197-XXX Video test warning 005-198-XXX Video test aborted...
Page 71
Diagnostic Error Code 006-195-XXX Diskette interface Test aborted by user 006-196-XXX Diskette interface test halt, error threshold exceeded 006-197-XXX Diskette interface test warning 006-198-XXX Diskette interface test aborted 006-199-XXX Diskette interface test failed, cause unknown 006-25X-XXX Diskette interface Error 011-000-XXX Serial port Interface Test Passed 011-001-XXX Serial port Presence...
Page 72
Diagnostic Error Code 011-195-XXX Serial port Test aborted by user 011-196-XXX Serial port test halt, error threshold exceeded 011-197-XXX Serial port test warning 011-198-XXX Serial port test aborted 011-199-XXX Serial port test failed, cause unknown 011-2XX-XXX Serial port signal failure 014-000-XXX Parallel port Interface Test Passed 014-001-XXX...
Page 73
Diagnostic Error Code 014-03X-XXX 014-04X-XXX Parallel port failure 014-195-XXX Parallel port Test aborted by user 014-196-XXX Parallel port test halt, error threshold exceeded 014-197-XXX Parallel port test warning 014-198-XXX Parallel port test aborted 014-199-XXX Parallel port test failed, cause unknown 014-2XX-XXX 014-3XX-XXX Parallel port failure...
Page 74
Diagnostic Error Code 015-034-XXX USB port buffer allocation failure 015-035-XXX USB port Reset condition detected 015-036-XXX USB port Register error 015-040-XXX USB port IRQ failure 015-195-XXX USB port Test aborted by user 015-196-XXX USB port test halt, error threshold exceeded 015-197-XXX USB port test warning 015-198-XXX...
Page 75
Diagnostic Error Code 018-196-XXX PCI Card test halt, error threshold exceeded 018-197-XXX PCI Card test warning 018-198-XXX PCI Card test aborted 018-199-XXX PCI Card test failed, cause unknown 018-250-XXX PCI Card Services error 020-000-XXX PCI Interface Test Passed 020-0XX-XXX PCI Interface error 020-195-XXX PCI Test aborted by user 020-196-XXX...
Page 76
Diagnostic Error Code 020-198-XXX PCI test aborted 020-199-XXX PCI test failed, cause unknown 020-262-XXX PCI system error 025-000-XXX IDE interface Test Passed 025-00X-XXX 025-01X-XXX IDE interface failure 025-027-XXX IDE interface Configuration/Setup error 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 025-195-XXX IDE interface Test aborted by user 025-196-XXX IDE interface test halt, error threshold exceeded...
Page 77
Diagnostic Error Code 025-198-XXX IDE interface test aborted 025-199-XXX IDE interface test failed, cause unknown 030-000-XXX SCSI interface Test Passed 030-00X-XXX 030-01X-XXX SCSI interface failure 030-027-XXX SCSI interface Configuration/Setup error 030-03X-XXX 030-04X-XXX SCSI interface error 030-195-XXX SCSI interface Test aborted by user 030-196-XXX SCSI interface test halt, error threshold exceeded...
Page 78
Diagnostic Error Code 030-198-XXX SCSI interface test aborted 030-199-XXX SCSI interface test failed, cause unknown 035-000-XXX RAID interface Test Passed 035-0XX-XXX RAID interface Failure 035-195-XXX RAID interface Test aborted by user 035-196-XXX RAID interface test halt, error threshold exceeded 035-197-XXX RAID interface test warning 035-198-XXX RAID interface test aborted...
Page 79
Diagnostic Error Code 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 071-03X-XXX Audio port failure 071-04X-XXX Audio port failure 071-195-XXX Audio port Test aborted by user 071-196-XXX Audio port test halt, error threshold exceeded 071-197-XXX Audio port test warning 071-198-XXX Audio port test aborted 071-199-XXX Audio port test failed, cause unknown 071-25X-XXX...
Page 80
Diagnostic Error Code 080-196-XXX Game Port interface test halt, error threshold exceeded 080-197-XXX Game Port interface test warning 080-198-XXX Game Port interface test aborted 080-199-XXX Game Port interface test failed, cause unknown 086-000-XXX Mouse Port interface Test Passed 086-001-XXX Mouse Port interface Presence 086-032-XXX Mouse Port interface Device controller failure...
Page 81
Diagnostic Error Code 086-197-XXX Mouse Port interface test warning 086-198-XXX Mouse Port interface test aborted 086-199-XXX Mouse Port interface test failed, cause unknown 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure 089-195-XXX Microprocessor Test aborted by user 089-196-XXX Microprocessor test halt, error threshold exceeded 089-197-XXX Microprocessor test warning...
Page 82
Diagnostic Error Code 170-0XX-XXX Voltage Sensor(s) failure 170-195-XXX Voltage Sensor(s) Test aborted by user 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 170-197-XXX Voltage Sensor(s) test warning 170-198-XXX Voltage Sensor(s) test aborted 170-199-XXX Voltage Sensor(s) test failed, cause unknown 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 170-254-XXX...
Page 83
Diagnostic Error Code 175-197-XXX Thermal Sensor(s) test warning 175-198-XXX Thermal Sensor(s) test aborted 175-199-XXX Thermal Sensor(s) test failed, cause unknown 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error 185-000-XXX Asset Security Test Passed 185-XXX-XXX Asset Security failure 185-278-XXX Asset Security Chassis Intrusion 201-000-XXX System Memory Test Passed 201-XXX-XXX...
Page 84
Diagnostic Error Code 215-000-XXX CD-ROM Drive Test Passed 215-XXX-XXX CD-ROM Drive error 217-000-XXX Hard Disk Drive Test Passed 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error 220-000-XXX Hi-Capacity Cartridge Drive Test Passed 220-XXX-XXX Hi-Capacity Cartridge Drive error 301-XXX-XXX Keyboard error 301-000-XXX...
Page 85
Diagnostic Error Code 415-000-XXX Modem Test Passed 415-XXX-XXX Modem error FRU/Action No action Remove the Modem and re-test the system Chapter 7. Symptom-to-FRU Index...
Beep symptoms Beep symptoms are short tones or a series of short tones separated by pauses (intervals without sound). See the following examples. Beeps 1-2-X Use the following table to diagnose beep symptoms. Beep Symptom 1-1-3 CMOS read-write error 1-2-2-3 ROM BIOS check error 1-2-1 Programmable Interval Timer failed...
Page 87
Beep Symptom 2-2-4 CMOS configuration info validation failed 2-3-1 Screen initialization failed 2-3-2 Screen memory failed 2-3-3 Screen retrace failed 1-2 Search for video ROM failed All other beep code sequences Continuous beep Repeating short beeps FRU/Action 1. Battery 2. System Board 1.
No-beep symptoms Symptom/Error No beep during POST but computer works correctly. No beep during POST. Hardware Maintenance Manual FRU/Action System board 1. See “Undetermined problems” on page 2. System Board 3. Memory Module 4. Any Adapter or Device 5. Riser Card 6.
POST error codes Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations. v Checks some basic system-board operations v Checks the memory operation v Starts the video operation...
Page 90
POST Error Code 191 System Security: Embedded Security hardware Reset 192 System Security: Embedded Security hardware tamper detected 193 System Security: Embedded Security hardware Removed 194 System Security: Asset ID Antenna has been Removed 195 System Security: Asset ID Antenna has been installed 196 System Tampered Cleared Memory error...
Page 91
POST Error Code 1801 PCI/PnP Error! No Space Available to Shadow ROM 1802 PCI/PnP Error! Not Enough I/O Space Available 1803 PCI/PnP Error! Not Enough Memory Space Available 1804 PCI/PnP Error! Not Enough Real Memory Space Available 1805 PCI/PnP Error! Adapter ROM Checksum Error 1962 No operating system found...
Miscellaneous error messages Message/Symptom CMOS Backup Battery inaccurate Changing colors Computer will not power-off. See “Power Supply Errors” on page 57. Computer will not RPL from server Computer will not perform a Wake on LAN (if applicable) Dead computer. See “Power Supply Errors” on page 57.
Page 93
Message/Symptom ″Insert a Diskette″ icon appears with a known-good diagnostics diskette in the first 3.5-inch diskette drive. Intensity or color varies from left to right of characters and color bars No power or fan not running Non-system disk or disk error-type message with a known-good diagnostic diskette.
Message/Symptom Some or all keys on the keyboard do not work Undetermined problems Check the power supply voltages (see “Power Supply Errors” on page 57). If the voltages are correct, return here and continue with the following steps. 1. Power-off the computer. 2.
Locating the connectors on the rear The following illustration shows the locations of the connectors on the rear of the computer. 1 PCI adapter slot 2 Integrated cable lock slot 3 Mouse connector 4 Keyboard connector 5 VGA monitor connector 6 Parallel connector 7 Serial connector Opening the cover...
Locating components The following illustration will help you locate the various components in the computer. 1 PCI riser 2 Power supply assembly 3 Optical drive eject button 4 Optical drive 5 Hard disk drive 6 Cable clip on PCI riser 7 Rear fan bracket assembly Chapter 8.
Identifying parts on the system board 1 Hard disk drive connector 2 Optical drive connector 3 PCI riser connector 4 12v power connector 5 Power connector 6 Front fan connector 7 Microprocessor Removing and replacing a memory module 1. Open the cover. See “Opening the cover” on page 90. 2.
4. Make sure the notch 1 on the new memory module is aligned correctly with the connector key 2 on the socket. Insert the memory module straight down into the connector until it snaps into position and the retaining clips are closed. 5.
4. Remove the PCI riser from the computer by pulling straight up on the blue handle provided. 5. Pivot the blue adapter latch upward and remove the failing adapter. 6. Remove the new adapter from its static-protective package. 7. Install the new adapter into the PCI connector in the riser. 8.
Page 101
2. Pivot the drive bay assembly upward to gain access to the system board. 3. Locate the rear fan bracket assembly. See “Locating components” on page 91. 4. Lift the rear fan bracket assembly up to gain access to the battery. 5.
Removing and replacing the power supply Attention Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no servicable parts inside these components.
7. Install the new power supply and insert the four screws that hold the power supply in place. 8. Replace the PCI riser. See “Removing and replacing a PCI adapter” on page 9. Reconnect all power supply cables to the system board and the drives. See “Identifying parts on the system board”...
Page 104
7. Remove the heat sink from the microprocessor by gently twisting the heat sink to break the seal formed by the thermal grease and lifting it straight up. 8. Place the heat sink on its side on a clean work surface so that the thermal grease is not contaminated.
Page 105
10. To remove the microprocessor 1 from the failing system board, lift the small handle 2 on the microprocessor socket to its maximum vertical position. Carefully lift the microprocessor off the socket. 11. To install the microprocessor on the new system board, position the microprocessor socket handle on the new system board to the full vertical position.
20. Go to “Completing the FRU replacement.” on page 104. Removing and replacing the microprocessor 1. Open the cover. See “Opening the cover” on page 90. 2. Loosen the two captured screws that secure the heat sink clamps 2 . Pivot the clamps to the side to allow the heat sink 1 to be removed.
Page 107
7. Position the microprocessor so that the pins are aligned with the socket and with the beveled corner 1 on the microprocessor is aligned in the socket as shown. 8. Lower the handle until it is fully in the down position and locked into the socket.
Removing and replacing an optical drive 1. Open the cover. See “Opening the cover” on page 90. 2. Push the optical drive eject button and slide the optical drive out of the front of the computer. 3. Slide the new drive into the bay until it is latched into position. 4.
Removing and replacing a hard disk drive 1. Open the cover. See “Opening the cover” on page 90. 2. Pivot the drive bay assembly upward to gain access to the hard disk drive. 3. Disconnect the signal and power cables from the rear of the hard disk drive. 4.
10. Go to “Completing the FRU replacement..” Completing the FRU replacement. After replacing FRUs, you need to install any removed parts, replace the cover, and reconnect any cables, including telephone lines and power cords. Also, depending on the FRU that is replaced, you might need to confirm the updated information in the Setup Utility program.
Machine Type 8089 Item # Top Cover (all models) PCI riser card and bracket assembly (all models) 200 W power supply-Hipro PFC (models 11U 12U 21U 22U 71G 72G 73G 74G 75G C1U C2U C3U C4U CTO 31U 32U 76G 77G C5U 23S 23D 13G) Hard disk drive 40GB 7200rpm EIDE ATA-100 (models 11U 12U 21U 22U 72G 74G 75G CTO 31U 32U 76G 13G) Hard disk drive 40GB 7200rpm EIDE ATA-100 (models 11U 12U 21U 22U 72G 74G...
Page 136
Item # Hard disk drive 80GB 7200rpm Serial ATA (models CTO) Hard disk drive 160GB 7200rpm Serial ATA (models CTO) Hard disk drive 160GB 7200rpm Serial ATA (models CTO) Hard disk drive 160GB 7200rpm Serial ATA (models CTO) Front Rotating Cage assembly (all models) CD-ROM (24x) Plus Ultrabay Enhanced Drive (models 11U 21U 72G 74G 75G CTO 31U 76G 13G) CD-ROM (24x) Plus Ultrabay Enhanced Drive (models 11U 21U 72G 74G 75G CTO...
Page 142
Item # Hard disk drive 80GB 7200rpm Serial ATA (models CTO) Hard disk drive 160GB 7200rpm Serial ATA (models CTO) Hard disk drive 160GB 7200rpm Serial ATA (models CTO) Hard disk drive 160GB 7200rpm Serial ATA (models CTO) Front Rotating Cage assembly (all models) CD-ROM (24x) Plus Ultrabay Enhanced Drive (models 11U A1U A2U 21U 71G 72G A3U CTO A7U 31U 73G A8G) CD-ROM (24x) Plus Ultrabay Enhanced Drive (models 11U A1U A2U 21U 71G...
7. Follow the instructions on the screen to complete the update. Updating (flashing) BIOS from your operating system Note: Due to constant improvements being made to the Lenovo Web site, Web page content (including the links referenced in the following procedure) is subject to change.
5. On the Flash BIOS Update page, scroll down to locate the .txt file for the flash from the operating system version. Click the .txt file. 6. Print these instructions. This is very important because these instructions are not on the screen after the download begins. 7.
Power management Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors. Automatic configuration and power interface (ACPI) BIOS Being an ACPI BIOS system, the operating system is allowed to control the power management features of the computer and the setting for Advanced Power Management (APM) BIOS mode is ignored.
Recovering software using the Rescue and Recovery program The Rescue and Recovery program provides an environment that runs independently of the Windows operating system and is hidden from the Windows operating system. Because the Rescue and Recovery workspace is hidden, it is immune from most virus attacks and provides a safe place to perform rescue and recovery operations that might not be possible in the Windows environment.
Macrovision Corporation. Reverse engineering or disassembly is prohibited. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo ThinkCentre PS/2...
Page 164
Part Number: 19R2387 Printed in USA (1P) P/N: 19R2387...