TopPage LC-37D90U SERVICE MANUAL No. S56S8LC37D90U LCD COLOR TELEVISION LC-37D90U MODEL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
LC-37D90U CONTENTS SAFETY PRECAUTION IMPORTANT SERVICE SAFETY PRE- CAUTION............i PRECAUTIONS A PRENDRE LORS DE LA REPARATION..........ii PRECAUTIONS FOR USING LEAD- FREE SOLDER..........iii CHAPTER 1. SPECIFICATIONS SPECIFICATIONS ........1-1 CHAPTER 2. OPERATION MANUAL OPERATION MANUAL ......
LC-37D90U LC-37D90U SAFETY PRECAUTION Service Manual IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: WARNING • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen- sitivity or measure the AC voltage drop across the resistor.
LC-37D90U PRECAUTIONS A PRENDRE LORS DE LA REP- ARATION Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT • A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ 10 watts en parallèle avec un condensateur de 0.15µF en série avec...
LC-37D90U PRECAUTIONS FOR USING LEAD-FREE SOL- Employing lead-free solder • "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
* Emergency alert messages via Cable are unreceivable. • As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.
LC-37D90U CHAPTER 4. LC-37D90U REMOVING OF MAJOR PARTS Service Manual [1] REMOVING OF MAJOR PARTS 1. Detach the SD Card Cover. 2. Remove the 2 lock screws and detach the Stand Cover. 3. Remove the 4 lock screws and detach the Stand.
Page 14
LC-37D90U 6. Remove the Stand Bottom Cover. 7. Disconnect the [FB] connector. Remove the 2 lock screws and detach the Fan Angle C Ass’y. 8. Remove the 4 lock screws and detach the SUS Angle (L)(R). 9. Remove the 5 lock screws and detach the Stand Fixing Angle.
Page 15
LC-37D90U 12.Remove the 3 lock screws and detach the Fan Angle L Ass’y. 13.Remove the 2 lock screws and detach the SP (L) PWB. 14.Remove the 3 lock screws and detach the SP Fixing Angle (L). 15.Remove the 2 lock screws and detach the SP (R) PWB.
Page 16
LC-37D90U 21.Remove the 9 lock screws and detach the Jack Angle Long. 22.Remove the 6 lock screws and detach the POWER PWB. 23.Remove the 6 lock screws and detach the IF PWB. 24.Remove the 5 lock screws and detach the MAIN PWB Radiator and MAIN PWB.
Page 17
LC-37D90U CHAPTER 5. LC-37D90U ADJUSTMENT Service Manual [1] ADJUSTMENT PROCEDURE The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is required due to part replacement, make an adjustment according to the following procedure.
Page 18
LC-37D90U 2. When the formatting is over, the following window appears. Click [OK]. 3. Click [Exit] to finish the formatting. NOTE: When you are done, take out the SD card once to make sure it is finished, and then insert it again.
Page 19
LC-37D90U 5. If any of the procedures fails, the following upgrade failure screen shows up. For the failing procedure, the “NG” marking turns red. NOTE: In such case, try to upgrade the software again. If it still fails, the hardware may be in trouble.
Page 20
LC-37D90U 4. A couple to dozen seconds after the set starts, the upgrade screen below shows up. The upgrade progress is indicated on screen. The power LED indicator goes out once and then starts flashing in blue. (It takes 2-3 minutes to get the monitor microprocessor software upgraded.) 5.
Page 21
LC-37D90U 3. Entering and exiting the adjustment process mode 1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu. 2) While holding down the “VOL (–)” and "INPUT" keys at a time, plug in the AC cord of the main unit to turn on the power.
Page 22
LC-37D90U 5. List of adjustment process mode menu The character string in brackets [ ] will appear as a page title in the adjustment process menu header. Page Line Item Description Remarks (adjustment detail, etc.) [INFO] MAIN Version Main software version...
Page 23
LC-37D90U Page Line Item Description Remarks (adjustment detail, etc.) [M GAMMA IN] MONITOR GAMMA IN 1 Standard value 1(LEV60050) Adjustment gradation setting. MONITOR GAMMA IN 2 Standard value 2(LEV60066) MONITOR GAMMA IN 3 Standard value 3(LEV60116) MONITOR GAMMA IN 4...
Page 26
LC-37D90U Page Line Item Description Remarks (adjustment detail, etc.) [M EEP SET] MONITOR TIME OUT MONITOR MAX TEMP MONITOR STANDBY CAUSE [M TESTPTRN] LCD TEST PATTERN [MEMORY CLR] KEY LOCK(1217) KOUTEI AREA ALL CLEAR A MODE AREA CLEAR BACKUP AREA CLEAR...
LC-37D90U 7.3. N358 composite signal adjustment (Tuner) Adjustment item Adjustment conditions Adjustment procedure Adjustment N358 signal Feed the PAL split field color bar signal (75% color saturation) to VIDEO 1 input. Feed the RF signal (by use of US-10ch) to TUNER-A.
Page 28
LC-37D90U Adjustment item Adjustment conditions Adjustment procedure Auto adjustment Page 7/27 Bring the cursor on [•DVI ANALOG] and press [ENTER]. performance [•DVI ANALOG ADJ FINISH] appears when finished. 8. Adjustment of white balance 8.1. White balance adjustment Adjustment item Adjustment conditions...
Page 29
LC-37D90U Level Standard value Adjustment value Tolerance Note Set the following before adjustment. AV MODE: [DYNAMIC] Monochrome: ON Aging Time: 60 Min. 8.2. Adjusting procedure by use of [RS-232C] 1. Get ready the PC with COM port (RS-232C) running on Windows 95/98/ME/2000/XP operating system, as well as the RS-232C cross cable.
Page 30
LC-37D90U 8.3. White balance adjustment sequence Adjustment is available in any input or position. There is no specific order to adjust high and low, either. Activate process command (STEP1). KRSW0001 Command is accepted. Activate process command (STEP2). KKT10037 Process command is activated.
Page 31
LC-37D90U Start of measurement Adjust RB to the target xy values. MG5RXXXX MG5BXXXX * XXXX indicates adjustment values between 0000 - 1023 (4 digit decimal number with zero fill). * G is fixed. Repeat until values are * Default adjustment value of RGB is the parameter value of LEV5 command multiplied by 4.
Page 32
LC-37D90U Start of measurement Adjust RB to the target xy values. MG2RXXXX MG2BXXXX * XXXX indicates adjustment values between 0000 - 1023 (4 digit decimal number with zero fill). * G is fixed. * Default adjustment value of RGB is the parameter value of LEV2 command multiplied by 4.
LC-37D90U [2] MAJOR IC INFORMATIONS 1. MAJOR IC INFORMATIONS 1.1. IC501 (MM1630CQ) This I2C bus-controlled video switch is designed to switch between one-system color difference (component) signal, one-system S video signal and two-system composite signal. The analog video signal from the INPUT-1 or INPUT-2 input terminal is fed into this IC for selection. The video output signal from this IC flows through a low-pass filter into the video signal processing circuit IC3301 (IXB723WJ).
Page 34
LC-37D90U 1.11. IC8101 (RH-iXB281WJZZQ) This LSI with MPEG-2 system decoder performs back-end processing for digital broadcasting. It is equipped with a CPU (processor core: AM33-3), descrambler (DES), transport stream de-multiplexer, video decoder (MPEG-2 MP@HL compatible), graphic processor, audio decoder (AC3 compati- ble), and an NTSC video encoder.
Page 35
LC-37D90U 2. MAJOR IC INFORMATIONS (BLOCK DIAGRAM AND PIN FUNCTION) 2.1. VHiMM1630CQ-1Q (ASSY: IC501) Video Switch with I2C-bus • Block Diagram [VHiMM1630CQ-1Q (ASSY: IC501)] • Pin Function [VHiMM1630CQ-1Q (ASSY: IC501)] Pin No. Pin Name Pin Function Chroma signal input. SW of S-terminal.
Page 36
LC-37D90U Pin No. Pin Name Pin Function S2-4 Detect of S-terminal. S2-5 S2-1 S2-2 S2-3 Luminance signal input. 8,47,53,57 Vcc Power supply. Slave address select terminal. BIAS Bias. 18,44,62 GND. Detect of D-terminal scanning line. Color difference siganl input. Detect of D-terminal I/P.
Page 37
LC-37D90U 2.2. VHiTA2024++-1Y (ASSY: IC2303) STEREO DIGITAL AUDIO AMPLIFIER • Block Diagram [VHiTA2024++-1Y (ASSY: IC2303)] • Pin Function [VHiTA2024++-1Y (ASSY: IC2303)] Pin No. Pin Name Pin Function DCAP2, Charge pump switching pins. DCAP1 (pin 3) is a free running 300kHz square wave between DCAP1 VDDA and DGND (12Vpp nominal).
Page 38
LC-37D90U 2.3. VHiAN5832SA-1Y (ASSY: IC1401) United States TV SAP SIF_DECODER • Block Diagram [VHiAN5832SA-1Y (ASSY: IC1401)] • Pin Function [VHiAN5832SA-1Y (ASSY: IC1401)] Pin No. Pin Name Pin Function Non connection. WB TIM Wide band timing. WB DET Wide band level sensor input terminal.
Page 39
LC-37D90U 2.4. VHiAK4683EQ-1Q (ASSY: IC1403) Asynchronous Multi-Channel Audio CODEC with DIR/T. • Block Diagram [VHiAK4683EQ-1Q (ASSY: IC1403)] • Pin Function [VHiAK4683EQ-1Q (ASSY: IC1403)] Pin No. Pin Name Pin Function PVDD PLL Power supply, 4.5V~5.5V. Receiver Channel 0 (Internal biased pin. Internally biased at PVDD/2).
Page 40
LC-37D90U Pin No. Pin Name Pin Function Zero Input Detect. When the input data of DAC follow total 8192 LRCK cycles with “0” input data, this pin goes to “H”. And when RSTN1 bit is “0”, PWDA bit is “0”, this pin goes to “H”.
Page 41
LC-37D90U 2.5. VHiNJU26111-1Q (ASSY: IC1406) SOUND_DSP • Block Diagram [VHiNJU26111-1Q (ASSY: IC1406)] • Pin Function [VHiNJU26111-1Q (ASSY: IC1406)] Pin No. Pin Name Pin Function SDO2 Audio Data Output CH2. SDO1 Audio Data Output CH1. SDO0 Audio Data Output CH0. GPIO0 General Purpose IO.
Page 46
LC-37D90U Pin No. Pin Name Pin Function MODE2 Input signal state detection. PMUTE Video mute. DDCRST IC1 reset. TVPOW2 LCD TOP PWB 1.2V/2.5V power control. Backlight control. PANEL_POW Panel power control signal. VSH_OUT Panel 3.3V control. MP_CLK 3-wire serial clock.
Page 47
LC-37D90U 2.9. RH-iXB723WJQZQ (ASSY: IC3301) VIDEO_PROCESSER • Pin Function [RH-iXB723WJQZQ (ASSY: IC3301)] Pin No. Pin Name Pin Function Ball Assignments for CPU Host Interface. C11, B11, A11, A12, B12, A_D [7:0] Multiplexed address and data bus with CPU Host Interface.
Page 48
LC-37D90U Pin No. Pin Name Pin Function AG3, AH3, AJ3, AK3, DP_B [19:10] Digital input port B [19:10]. AH4, AG4, AG5, AH5, AJ5, AK5 AK6, AJ6, AH6, AG6, DP_B [9:0] Digital input port B [9:0]. AG7, AH7, AJ7, AK7, AK8,...
Page 49
LC-37D90U Pin No. Pin Name Pin Function MVREF DDR voltage reference. Bank address select. Bank address select. Ball Assignments for Power and Ground. A2, A3, A4, A5, B3, B4, VDDC 1.8V Digital core power. B5, B6, C4, C5, C6, D4,...
Page 50
LC-37D90U Pin No. Pin Name Pin Function AVSS_OUTBUF 3.3V ground for output. AD27, AG27 LVDS_VSSO LVDS out buffer ground. AE24 LVDS_VSSD LVDS Digital ground. AF27 LVDS_VSSA LVDS analog ground. AH27 LVDS_VSSP LVDS PLL ground. AH28 LVDS_VDDP LVDS PLL power. AF28 LVDS_VDDA LVDS analog power.
Page 51
LC-37D90U 2.10. RH-iXB375WJZZQ (ASSY: IC3501, 3502) 128Mbit GDDR SDRAM • Block Diagram [RH-iXB375WJZZQ (ASSY: IC3501, 3502)] • Pin Function [RH-iXB375WJZZQ (ASSY: IC3501, 3502)] Pin No. Pin Name Pin Function 11M, 12M CK, CK*1 The differential system clock Input. All of the inputs are sampled on the rising edge of the clock except DQ’s and DM’s that are sampled on both edges of the DQS.
Page 52
LC-37D90U Pin No. Pin Name Pin Function 7B, 6C, 6B, DQ0 - DQ31 Data inputs/Outputs are multiplexed on the same pins. 5B, 2C, 3D, 2D, 2E, 13K, 12K, 13J, 12J, 13G, 12G, 13F, 12F, 3F, 2F, 3G, 2G, 3J, 2J, 3K, 2K,...
Page 58
LC-37D90U Pin No. Pin Name Pin Function ACLSYC Pin condition control. Shared with UACTS3_N. ACLSDI Serial data input. Shared with UARXD3. ACLSDO Serial data output. Shared with UATXD3. ACLBCLK Bit clock. Shared with UA3EXCLK. TM0EXCLK Timer0 clock. Shared with and PIO26.
Page 59
LC-37D90U Pin No. Pin Name Pin Function TS1DATA7 Transport stream port1 data input (Parallel). TS1DATA6 TS1DATA5 TS1DATA4 TS1DATA3 TS1DATA2 TS1DATA1 TS1DATA0 TS1VALID Transport stream port1 data valid. TS1SYNC Transport stream port1 data sync. TS1ERROR Transport stream port1 data error. TS1CLK Transport stream port1 data clock.
Page 60
LC-37D90U Pin No. Pin Name Pin Function AM32 VIDINCBCR1 External video data CB/CR input1. Shared with DBUGTPC1. AM33 VIDINCBCR0 External video data CB/CR input0. AL23 HDOUT Horizontal sync output. AK24 VDOUT Vertical sync output. AK23 DOUTCLK Display clock output. AK22 DOUTY9 Video Y output9 or Video G output9.
Page 61
LC-37D90U Pin No. Pin Name Pin Function CLKX8 PLL for Audio/Video Decoder. AH30 JTAGTCK Test clock input. AK32 JTAGTDO Test Data output. AJ31 JTAGTDI Test Data input. AL32 JTAGTMS Test mode select. AL33 JTAGTRST_N Test reset. AK33 JTAGGDBGSEL Connected to “H”.
Page 63
LC-37D90U 2.12. RH-iXB024WJZZQ (ASSY: IC8301-4) 256Mb F-die DDR SDRAM • Block Diagram [RH-iXB024WJZZQ (ASSY: IC8301-4)] • Pin Function [RH-iXB024WJZZQ (ASSY: IC8301-4)] Pin No. Pin Name Pin Function 45, 46 CK, CK Clock : CK and CK are differential clock inputs. All address and control input signals are sampled on the positive edge of CK and negative edge of CK.
Page 64
LC-37D90U Pin No. Pin Name Pin Function 2, 4, 5, 7, DQ [0 : 15] Data Input/Output : Data bus. 8, 10, 11, 13, 54, 56, 57, 59, 60, 62, 63, 16, 51 L(U)DQS Data Strobe : Output with read data, input with write data. Edge-aligned with read data, centered in write data.
Page 66
LC-37D90U 2.14. RH-iXB323WJZZQ (ASSY: IC8503) IEEE 1394a Link-Layer Controllers • Block Diagram [RH-iXB323WJZZQ (ASSY: IC8503)] • Pin Function [RH-iXB323WJZZQ (ASSY: IC8503)] Pin No. Pin Name Pin Function Audio PLL VCO_CLK Input from VCO. This is used to generate internal audio clocks for receive clock recovery.
Page 67
LC-37D90U Pin No. Pin Name Pin Function JTAG_TCK JTAG Test Clock pin. JTAG_TRSTn JTAG Reset pin. Active Low only. MCIF Interface (PCI, 68K and SRAM-Like Interface MCIF_SEL1 Microcontroller Interface Select. This pin is sampled at power-up and reset. MCIF_SEL [1: 0].
Page 68
LC-37D90U Pin No. Pin Name Pin Function DMAREQ_CH0n External DMA Request Signal-Channel 0. The RH-IXB323WJZZ will drive this signal low when it is ready for the system DMA controller. This signal is hi-Z when not driven low. DMAACK_CH0n External DMA Acknowledge Signal-Channel 0. The system DMA controller will drive this high when it has received DMAREQ_CH0n signal and is ready to transfer data.
Page 69
LC-37D90U Pin No. Pin Name Pin Function HSDI1_DVALIDz HSDI port 1 data Valid pin. This pin indicates if data on the HSDI data bus is valid for reading or writ- (HSDI1_Enz) ing. For transmit onto 1394, this signal is input to the RH-IXB323WJZZQ by the system with the data.
Page 70
LC-37D90U Pin No. Pin Name Pin Function GPIO2 GPIO. Output is controlled by the internal register. Input is monitored by internal register. Can be used as watermark for also buffer 1. GPIO3 GPIO. Output is controlled by the internal register. Input is monitored by internal register.
Page 71
LC-37D90U 2.15. RH-iXB684WJQZQ (ASSY: IC8601) DEMODULATOR • Block Diagram [RH-iXB684WJQZQ (ASSY: IC8601)] • Pin Function [RH-iXB684WJQZQ (ASSY: IC8601)] Pin No. Pin Name Pin Function Analog to Digital Converter (ADC) Interface ADC_INN ADC negative differential input. ADC_INP ADC positive differential input.
Page 72
LC-37D90U Pin No. Pin Name Pin Function 8, 13, 16, 18, AGND Analog Ground. 19, 21, 24, 29, 30, 124 20, 23, 27, 28 AVDD Analog power. (1.8V) 12, 15 AVDD_ADC ADC analog power. (1.8V) AVDD_OSC Oscillator analog power. (1.8V) AVDD_PLL PLL analog power.
Page 73
LC-37D90U 2.16. VHiTC6384AF1EQ (ASSY: IC8702) SD_CARD_CONTROLER • Pin Function [VHiTC6384AF1EQ (ASSY: IC8702)] Pin No. Pin Name Pin Function Host interface Chip select (accessible in #CS= “0”). 98, 97, 94, A [7:0] Address bit 7-0. 93, 88, 85, 82, 77 13, 11, 10, D [15:1] Data bit [15:0].
Page 74
LC-37D90U Pin No. Pin Name Pin Function LED2 LED output terminal for debugging. It is controlled by an internal register and it synchronizes with the operation of SD2. LED1 LED output terminal for debugging. It is controlled by an internal register and it synchronizes with the operation of SD1.
LC-37D90U CHAPTER 6. LC-37D90U TROUBLE SHOOTING TABLE Service Manual [1] TROUBLE SHOOTING TABLE <Power Supply> No power supply (Front LED does not light up) and no power-up even if turned on(Front LED light up to green) Is the AC power cord plugged in? Plug in the AC power cord and turn on the power.
Page 81
L C - 3 7 D 9 0 U Check D4705 and D4706 for defects. Check the primary-side parts for defects. See if the second- ary output is short-circuited. Is there the PNL12V output? Is PNL_POW (pin (4) of CN5702) at High (about 3.3V)? Check the PNL12V series regulator Check the main unit for trou- circuit.
Page 82
LC-37D90U No video (1) COMPOSITE: No external input video COMPOSITE: No external input video S-VIDEO: No external input video [INPUT-2] [INPUT-1] [INPUT-2] Is INPUT-1 selected on the input select Is INPUT-2 selected on the input select Is INPUT-2 selected on the input select menu...
Page 83
LC-37D90U [COMPOSITE signal input] Is there the COMPOSITE video signal input at pins (M4, N4) of IC3301 (VPC)? Check the line between SC1101 and IC3301 (Q2201 thru Q2203, [S-VIDEO signal input] Is there the video signal input at pins (M4, N4)(Y) and (T1)(C) of IC3301 (VPC)? Q2205, Q2207.
Page 84
LC-37D90U No video (2) COMPONENT: No external input video No video at UHF/VHF broadcast signal recep- No video at digital broadcast signal reception [INPUT-1] tion Is INPUT-1 selected on the input select Is the specified TV signal selected on the input select menu screen?
Page 85
LC-37D90U Is there the COMPONENT video signal out- Check the line between IC1103 Are there the MVY[7:0], MVC[7:0] and MVCLK/ put at pins (2), (4) and (6) of connector and IC3301 (Q2204, Q2208, MNSYNCO/MVSYNCO signal outputs from (SC501) on the IF unit? etc.).
Page 86
LC-37D90U <HDMI signal input> No video (3) No external input video [INPUT-3] No external input video [INPUT-4] Is INPUT-3 selected on the input select menu screen? Is INPUT-4 selected on the input select menu screen? Select INPUT-3 on the input select menu screen for the Select INPUT-4 on the input select menu screen for the right input signal.
Page 87
LC-37D90U Does the signal come from connector (SC1501) to the input pins (48 and Does the signal come from connector (SC1502) to the input pins (67 49) (CLK±), (51 and 52) (D0±), (54 and 55) (D1±), and (57 and 58) and 68) (CLK±), (70 and 71) (D0±), (73 and 74) (D1±), and (76 and 77)
Page 88
LC-37D90U <DVI signal input> No video (4) No external digital input video [INPUT-5] No external analog input video [INPUT-5] Is INPUT-5 selected on the input select menu screen? Is INPUT-5 selected on the input select menu screen? Select INPUT-5 on the input select menu screen for Select INPUT-5 on the input select menu screen for the the right input signal (AUTO or DIGITAL).
Page 89
LC-37D90U Is IC1505 (EEPROM) accessed by I2C, with DVI connected, to read the DDC_I2C CLOCK/DATA data? Does the signal come from pins (34 and 35) (CLK±), (31 and 32) Check the DDC line and its peripheral circuits (IC1505 (D0±), (28 and 29) (D1±), and (25 and 26) (D2±) of IC1507 to pins (EEPROM) and its peripherals).
Page 90
LC-37D90U No audio (1) [With HDMI connected] No audio (2) [Audio signal] INPUT-4 No audio (HDMI analog [Audio signal] INPUT-3 No audio (HDMI [Audio signal] INPUT-1 No audio input) connected) [Audio signal] INPUT-5 No audio (DVI analog [Audio signal] INPUT-4 No audio (HDMI...
Page 91
LC-37D90U Check the SC502 and SC1102 connectors. Check the line between IC1508 and IC1403 and their peripheral circuits. [INPUT-1] Does the audio signal come from pins (2) and (4) of SC1102 to pins (53)(L) and (54)(R) of IC1403 (CODEC)? [INPUT-2] Does the audio signal come from...
Page 92
LC-37D90U No audio (4) No audio at digital broadcast No audio at UHF/VHF broad- signal reception cast signal reception Move the sound volume key. Set the audio output to Is the audio output selected for Set the audio output to Does the volume icon indicate “FIXED”.
Page 93
LC-37D90U Are the audio signal inputs at Check the line between pins (61)(L) and (62)(R) of IC8801 and IC1403, and IC1403? their peripheral circuits. Are the audio signal outputs Check IC1403 and its at pins (38)(L) and (39)(R) of peripheral circuits.
Page 94
LC-37D90U No audio signal at DIGITAL AUDIO OUTPUT terminal (Analog sound heard) No INPUT-3/4 (HDMI) audio No audio at digital broadcast signal reception If no video appears, refer Are there the IF_OUT_N Check the tuner to “No external input video...
Page 95
LC-37D90U Is the audio output from the Check the bus line monitor set at “VARIABLE” (SCL0/SDA0_5) and or “FIXED” on the menu IC1403. Replace as screen? required. Is there the MUTE signal Check the input at pin (2) of IC1408? MUTE_A_ALL and ACDET_MUTE signals.
Page 96
LC-37D90U LED flashing timing chart for error notification. 250ms 1sec 1) Red power LED Remarks Error type Power red LED operation (1 cycle) Pins are microprocessor pins. Lamp failure ERR_PNL (pin 73 of IC2002): Abnormal L. Confirmed after 5 Flashes once: Fast L: Off...
Page 97
LC-37D90U Basically, communication logs are analyzed by a bus Error type Power red LED operation (1 cycle) monitor or debug print logs are analyzed. Time-out setting reception failu Time-out setting and start-up mode change cannot be H: On Start-up confirmation reception failure received from the main CPU.
LC-37D90U CHAPTER 8. LC-37D90U SCHEMATIC DIAGRAM Service Manual [1] DESCRIPTION OF SCHEMATIC DIA- GRAM 1. VOLTAGE MEASUREMENT CONDITION: 1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 120V. Signals are fed by a color bar signal generator for servicing purpose and the above volt- ages are measured with a 20k ohm/V tester.
LC-37D90U [3] R/C, LED Unit R/C, LED Unit (Side-A) C101 P101 D102 D103 RMC101 R104 IC101 Q101 SLD101 Q103 R102 R105 R112 Q102 D101 C104 R109 R/C, LED Unit (Chip Parts Side-A) [4] KEY Unit KEY Unit (Side-A) 9 – 11...
LC-37D90U [5] SPEAKER TERMINAL-L Unit SPEAKER TERMINAL-L Unit (Side-A) SPEAKER TERMINAL-L Unit (Side-B) [6] SPEAKER TERMINAL-R Unit SPEAKER TERMINAL-R Unit (Side-A) SPEAKER TERMINAL-R Unit (Side-B) 9 – 12...
LC-37D90U PartsGuide PARTS GUIDE No. S56S8LC37D90U Note: The reference numbers on the PWB are arranged in alphabetical order. LC-37D90U Please exchange MAIN unit, when you MODEL exchange IC8301, IC8302, IC8303, IC8304 and IC8453. CONTENTS PRINTED WIRING BOARD TERMINAL-L Unit) ASSEMBLIES (NOT...
Page 174
LC-37D90U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [1] PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) R/C, LED Unit DUNTKD641FM10 IF Unit DUNTKD643FM11 KEY Unit DUNTKD716FM06 MAIN Unit DKEYDD743FM21 SPEAKER TERMINAL-L Unit DUNTKD744WE01 DUNTKD745WE01 SPEAKER TERMINAL-R Unit POWER Unit...
Page 203
LC-37D90U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [9] CABINET AND MECHANICAL PARTS Front Cabinet Ass'y CCABAB315WJ01 Front Cabinet Not Available LED Cover GCOVAB501WJSA Badge, SHARP Not Available Decoration Plate HDECCA010WJSA Spacer, x2 PSPAHA416WJZZ Spacer, x2 PSPAHA801WJZZ Rear Cabinet Ass'y...
Page 204
LC-37D90U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [9] CABINET AND MECHANICAL PARTS Connecting Cord (LA:POW-INV1,3) QCNW-E439WJQZ Connecting Cord (LP:MAIN-LCDCONT) QCNW-E503WJQZ Connecting Cord (COAXIAL:IF-MAIN) QCNW-E513WJPZ Connecting Cord (LB:MAIN-INV3) QCNW-E516WJQZ Connecting Cord (PD+PE:MAIN-POW) QCNW-E517WJQZ QCNW-E519WJQZ Connecting Cord (FD:MAIN-POW) Connecting Cord (RA:LED-IF)
Page 205
LC-37D90U [11] PACKING PARTS (NOT REPLACEMENT ITEM) PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [11] PACKING PARTS (NOT REPLACEMENT ITEM) Packing Case SPAKCC517WJZZ Stand Sheet SPAKFA977WJZZ Wrapping Paper (Monitor) SPAKPA338WJZZ Wrapping Paper (Stand) SPAKPA487WJZZ SPAKXB057WJZZ Packing Add. (Top) (Bottom) SPAKXB058WJZZ Packing Add.
Page 206
LC-37D90U PRICE PART PARTS CODE DESCRIPTION RANK MARK RANK [12] SERVICE JIGS (USE FOR SERVICING) 80pins FFC L=1000mm Pitch=0.5mm, x2used QCNW-C222WJQZ LCD Controller Unit to LCD Panel RCA Cable L=1500mm, Tuner Extension QCNW-C799WJPZ 41pins L=400mm (LV) QCNW-E134WJPZ 12-14pins L=1000mm (LA)
Page 208
LC-37D90U COPYRIGHT 2006 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.