Related Manuals for Epson EHDMC10
Summary of Contents for Epson EHDMC10
- Page 1 Wireless Mirroring Adapter EHDMC10 Copyright©2014 Seiko Epson Corporation. All rights reserved. 2014.06...
-
Page 2: Safety Instructions
Introduction Thank you very much for purchasing this product. Make sure you read this guide before using the product to ensure you use it safely and correctly. Keep this guide in a safe place so that you can access it easily if you have any questions in the future. - Page 3 If you notice any of the following abnormalities, turn off the product immediately, unplug the power cable from the electrical outlet, and contact your local dealer or Epson service call center. • If you see smoke coming from the product, or notice abnormal odors or sounds.
- Page 4 Except as indicated in the "User's Guide", the case for this product should only be opened by qualified service personnel. Do not disassemble or remodel this product or its consumables. Many sections inside the product carry a high electrical charge which could cause a fire or electric shock to occur.
- Page 5 For safety reasons, make sure you unplug the power cable from the electrical outlet when the product is not in use. If the insulation has degraded, a fire could occur. When using this product, make sure it is at least 22 cm (8 inches) away from your body. WARNING: This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm.
-
Page 6: Included Items
Included Items Wireless/ Wireless Wireless Pass-Thru Connect Ready Link Base unit micro USB cable AC adapter (Depend on country) An HDMI cable is not included. To connect an HDMI device, you need to ob- tain a commercially available HDMI cable. Parts and Functions Ports Reset button... -
Page 7: Buttons And Indicators
Buttons and Indicators Slide switch Changes between the Source and Sink functions. Wireless/Pass-Thru button When sliding the switch to [Source]: Switches the output device between the MOVERIO BT-200 and the device connected to the HDMI Output. When sliding the switch to [Sink]: Switches the input device between the MOVERIO BT-200 and the device connected to the HDMI Input. - Page 8 Connections Sending images from a video device to your MOVERIO BT-200 (Source function) Connect a commercially available HDMI cable to the HDMI Input port on this unit and to the HDMI output port on the device that is sending images. Set the slide switch to Source.
- Page 9 Connecting (MOVERIO BT-200 Operations) 1. Launch MOVERIO Mirror that comes preinstalled on MOVERIO BT-200. 2. Tap [Sink] on the MOVERIO Mirror main screen. 3. Tap [Target Device]. 4. Tap the Adapter Name (EHDMC1-XXXXXX) attached to this unit from the list of available devices. The status displayed below Adapter Name changes to [Invited], and connection starts.
- Page 10 Receiving images from MOVERIO BT-200 to output to a television (Sink function) Connect a commercially available HDMI cable to the HDMI Output port on this unit and to the HDMI input port on the device that is receiving images. Image receiving device Image sending device Wireless/ Wireless...
- Page 11 Connecting (MOVERIO BT-200 Operations) 1. Launch MOVERIO Mirror that comes preinstalled on MOVERIO BT-200. 2. Tap [Source] on the MOVERIO Mir- ror main screen. 3. Tap [Target Device]. 4. Tap the Adapter Name (EHDMC1-XXXXXX) attached to this unit from the list of available devices. The status displayed below Adapter Name changes to [Invited], and connection starts.
- Page 12 2. Enter the displayed IP address in the URL bar on your browser. The setup screen is displayed. 3. Make the necessary settings. Item Function Setting Select on or off as the power saving setting. Update the firmware for the unit. Check the lat- Firmware Update est firmware at http://www.epson.com...
-
Page 13: Troubleshooting
Troubleshooting Cannot send or receive images • Check that the micro USB cable is connected correctly. • Check that the AC adapter is connected to the electrical outlet correctly. • Check that the devices are connected to the HDMI Input or the HDMI Output correctly. -
Page 14: Specifications
Miracast : 640x480p @60Hz 1280x720p @25/30Hz Power (AC adapter) 100 to 240 VAC ± 10% 50/60Hz Power supply Power (EHDMC10) 5 VDC During Miracast communication: 5W Power consump- tion During power saving (No signal): 0.3W Temperature: +5 to +35°C (41 to 95 °F) -
Page 15: About Trademarks
Modulation: OFDM and DS-SS Assumed interference distance: 10m (32.8 feet) Information on Supported Devices Visit the http://www.epson.com web site for information on devices that can send and receive image content using this product. About Trademarks Miracast™ is a trademark of the Wi-Fi Alliance. -
Page 16: Wireless Telegraphy Act Regulations
Wireless Telegraphy Act Regulations The following acts are prohibited by the Wireless Telegraphy Act. • Modifying and disassembling (including the antenna) • Removing the label of conformance Restriction of Use This product is manufactured based on the specifications of the country of sale. -
Page 17: Fcc Compliance Statement
Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We : Epson America, Inc. Located at : 3840 Kilroy Airport Way MS : 3-13 Long Beach, CA 90806 Tel : 562-981-3840 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. - Page 18 more of the following measures. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
- Page 19 This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numèrique de la classe B est conforme à la norme NMB-003 du Canada. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance.