Advertisement
Table of Contents
- 1 Table of Contents
- 2 Warning
- 3 Introduction
- 4 Important Installation Information
- 5 Step 1: Ventilation Requirements
- 6 Step 2: Cabinet Preparation
- 7 Step 3: Unpacking, Moving and Placing the Range
- 8 Step 4: Install Anti-Tip Device
- 9 Step 5: Gas Requirements & Hookup
- 10 Step 6: Electrical Requirements, Connection & Grounding
- 11 Step 7: Backguard Installation
- 12 Step 8: Test and Adjustment
- 13 To Clean and Protect Exterior Surfaces
- 14 Installer Checklist
- Download this manual
INSTALLATION INSTRUCTIONS MANUAL
ALL-GAS MODELS PRSG304 AND PRSG36,
DUAL-FUEL MODELS PRSE304, PRSE36 AND PRSE48
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
IMPORTANT: LOCAL CODES VARY. INSTALLATION, ELECTRICAL CONNECTIONS,
GAS CONNECTIONS, AND GROUNDING MUST COMPLY WITH ALL APPLICABLE CODES.
IMPORTANT: Save these instructions for the Local Electrical Inspector's use.
INSTALLER: Please leave these Installation Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Gas Supply:
Natural Gas – 6 inch water column.
Propane Gas – 11 inch water column.
Electrical Power Supply:
PRSG304 and PRSG36 Models – 120 VAC, 60 Hz., 1Ph., 15 Amp circuit.
PRSE304 Model - 120/240 VAC, 60 Hz., 1Ph., 20 Amp circuit.
PRSE36 Models – 120/240 VAC, 60 Hz., 1Ph., 30 Amp circuit.
PRSE48 Models – 120/240 VAC, 60 Hz., 1Ph., 50 Amp circuit.
PROFESSIONAL RANGES
For Residential Use Only
WARNING: Disconnect power before
installing. Before turning power ON,
be sure that all controls are in the
A P P R O V E D
®
OFF position.
Page 1
Advertisement
Table of Contents
Related Manuals for Thermador PRSG304
Summary of Contents for Thermador PRSG304
- Page 1 Propane Gas – 11 inch water column. Electrical Power Supply: PRSG304 and PRSG36 Models – 120 VAC, 60 Hz., 1Ph., 15 Amp circuit. PRSE304 Model - 120/240 VAC, 60 Hz., 1Ph., 20 Amp circuit. PRSE36 Models – 120/240 VAC, 60 Hz., 1Ph., 30 Amp circuit.
-
Page 2: Table Of Contents
Ranges are free standing units avail- alteration, service or main- able in a number of configurations. tenance can cause injury or Model PRSG304 is equipped with four property damage. Refer to sealed gas surface burners and a large capacity gas oven with gas infra-red this manual. -
Page 3: Important Installation Information
This may be particularly beneficial for those cases, such as a long duct run or heavy usage of the grill, in which improved capturing of the cooking exhaust is desired. ** Thermador offers a choice of remote (VTR1000Q or VTR1400Q) or in-hood (VTN1000Q) blowers for use in wall installations. Page 3... -
Page 4: Step 2: Cabinet Preparation
Do not install the Model the cooking surface, a Ranges must be placed with PRES304 and PRSE48 Thermador Low Back or High the oven door projecting out ranges such that the oven Shelf backguard must be from the cabinet face. The door is flush with the installed. - Page 5 30" Range) 0" 0" Clearance Clearance ➝ ➝ 25" 24-3/8" PRSG304 - 16-1/2" PRSE36 - 28" PRSE36 - 15-3/8" 26-3/8" PRSE48 - 27" PRSE48 - 16-3/8" PRSE304 -18-3/8" ∆ as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Issue).
- Page 6 STEP 2: CABINET PREPARATION GAS AND ELECTRIC SUPPLY ZONES: FIG. 3a Gas & Electrical Supply Zone for PRSG304 & PRSG36 All-Gas Ranges The All-Gas Ranges are factory equipped with a power supply cord 5/8" Flex Line to Typical placement shown.
- Page 7 STEP 2: CABINET PREPARATION ELECTRICAL SUPPLY, DUAL FUEL RANGES Installation of Dual Fuel ranges This is especially critical if the must be planned so that the junction box in the wall will be rough-in of the junction box for directly behind the junction box the receptacle or conduit con- on the unit when the unit is nection will allow maximum...
-
Page 8: Step 3: Unpacking, Moving And Placing The Range
STEP 3: UNPACKING, MOVING AND PLACING THE RANGE CAUTION: Chart A 30" Range 36 " Range 48" Range Shipping Weight 335 lbs. 444 lbs. 584 lbs. Proper equipment and adequate manpower must Weight without 285 lbs. 390 lbs. 524 lbs. be used in moving the range packing materials to avoid damage to the unit... - Page 9 STEP 3: UNPACKING, MOVING AND PLACING THE RANGE • Due to the weight, a dolly with FIG. 7 Dolly Positioning soft wheels should be used to move this unit. The weight must Range be supported uniformly across Must be Uniformly the bottom (See Fig.
-
Page 10: Step 4: Install Anti-Tip Device
STEP 4: INSTALLING ANTI-TIP DEVICE For all 30" and 36" ranges, an anti-tip device must be installed as per these instructions. WARNING RANGE TIPPING HAZARD WARNING • All ranges can tip and injury could result. To prevent accidental tipping of the range, attach it to the wall, floor or cabi- •... - Page 11 STEP 4: INSTALLING ANTI-TIP DEVICE Parts Required for Installation of Anti-Tip Device: PRSG304 and PRSG36 All-Gas Ranges (Figures 9 and 10) FIG. 9. Mounting Kit for PRSG304 and Thermador Part No. Qty. Description PRSG36 All Gas Ranges 15-10-916 Screw, Phillips, #10 x 1-1/2”...
- Page 12 STEP 4: INSTALLING ANTI-TIP DEVICE PRSG304 and PRSG36 All-Gas Ranges (Figures 9, 10, 12A, 12B, and 13) STEP A: Determine the best location for the FIG. 12A. PRSG Wall Mount (0" Clearance) PRSG Mounting Bracket. The bracket may be PLAN VIEW...
- Page 13 From the bottom of the channel, screw the two (2) #10 x 1/2” Phillips Screws up through holes extending beyond the rear the first pair of PRSG304: 2-3/4" 7/16" PRSG36: 4-5/8" edge of the range flange. These screws will prevent rotation of the channel.
- Page 14 STEP 4: INSTALLING ANTI-TIP DEVICE FIG. 14 PRSE Wall Mount STEP B: Set the bracket on the floor and turn it until it is oriented properly. The long channel should be on the top with the free end facing towards you, one set of mounting flanges should be resting horizontally on the floor, and the other set of mounting flanges should be positioned vertically facing the rear.
-
Page 15: Step 5: Gas Requirements & Hookup
Contact the supply. The supply line must not interfere with the dealer when the unit was purchased or Thermador (800/735- back of the unit. Make sure the gas supply is turned 4328). The field conversion kit for all Professional Series off at the manual shut-off valve before connecting the ranges is Thermador Model PROLPKIT, PN 35-00-549. -
Page 16: Step 6: Electrical Requirements, Connection & Grounding
PRSE304, PRSE36 and PRSE48 electrical supply cord, if so can be cord-connected or hard- equipped, from wall receptacle. If • Gas range models PRSG304 and wired to the power supply, as appliance is hard-wired to power PRSG36 must be plugged into a described on Page 17. - Page 17 STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING Dual Fuel range models PRSE304, PRSE36 and PRSE48 must be connected to the power supply utilizing one of the following methods. For all methods of connection, the length of the cord or conduit/wiring must allow the unit to be slid completely out of the cabinet without having to unplug or disconnect the unit from the power supply.
- Page 18 STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING A 3 or 4 conductor supply may be connected to FIG. 17 Conductor Securement the terminal block. A 4-conductor supply shall be used only when the range is installed in a mobile home or where local codes do not permit ground- Cupped Washer ing through the neutral.
- Page 19 STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING Recommended Grounding Method – FIG. 19 Recommended Models PRSG304 and PRSG36 Grounding Method – Models PRSG304 and PRSG36 The 30" and 36" all-gas ranges are factory equipped with a power supply cord with a three-prong grounding plug (with polarized parallel blades).
-
Page 20: Step 7: Backguard Installation
PRSE304 and PRSE36 units, Page 21. Chart E: BACKGUARD KIT MODEL NUMBERS RANGE MODEL NO. 9" STD. LOW BACK 12" LOW BACK 22" HIGH SHELF 1-1/2" ISLAND TRIM PRSE304/PRSG304 Included with Range PHS30T PRS30ITS PRSE36/PRSG36 PRS36LBS PHS36T PRS36ITS PRSE48... -
Page 21: Step 8: Test And Adjustment
Step 2 Slide insulation retainer and insulation out and discard. See Fig. 22b. NOTE: DO NOT REMOVE INSULATION WHEN INSTALLING A BACKGUARD ON MODEL PRSG304 ALL-GAS RANGE AND MODEL PRSG36 ALL-GAS RANGES STEP 8: TEST AND ADJUSTMENT Install any loose components, such as burner caps and grates, that may CAUTION have been removed earlier. -
Page 22: To Clean And Protect Exterior Surfaces
STEP 8: TEST AND ADJUSTMENT PROPER FLAME (APPROX.) FIG. 23 * The gas oven infra-red broiler burner has no air shutter and Griddle, Grill, & Gas Oven Burners is not adjustable when used with natural gas. When used on propane gas, an air shutter is attached, but it is not adjustable. -
Page 23: Installer Checklist
INSTALLER CHECKLIST FINAL CHECK LIST that the propane gas supply is certified for use. equipped with its own high ❑ ❑ Placement of unit. pressure regulator in addition Manual gas shut off valve to the pressure regulator installed in an accessible ❑... - Page 24 We reserve the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the U. S. for use in Canada. Check with your local Canadian distributor or dealer.