Table of Contents
Advertisement
Table of contens
Chapter 2
Overview .................................................................................39(E)
Structure of the SYSTEM CONFIG Menu .............................40(E)
Setting Lists of the SYSTEM CONFIG Menu........................40(E)
Overview .................................................................................42(E)
Structure of the STATUS Menu..............................................42(E)
Setting Lists of the STATUS Menu ........................................ 42(E)
Overview .................................................................................43(E)
Structure of the ALIGNMENT Menu ..................................... 43(E)
Setting Lists of the ALIGNMENT Menu ...............................43(E)
Selecting the Monitor to Control - ADDRESS Menu ............... 45(E)
Overview .................................................................................45(E)
Displaying the ADDRESS Menu ............................................45(E)
Cancelling the Remote Control Mode ..................................... 46(E)
Exiting the ADDRESS Menu .................................................. 46(E)
Short-cut Function in the ADDRESS Menu ........................... 46(E)
Specifications ................................................................................... 47(E)
Chapter 3
Available Signal Format..........................................................53(E)
Appendix
Menu Index ..................................................................................... 56(E)
Menu Configuration ....................................................................... 58(E)
2
(E)
Precautions
On safety
• Operate the unit only with a power source as
specified in "Specifications" section.
• The nameplate indicating operating voltage, power
consumption, etc., is located at the rear.
• Should any solid object or liquid fall into the cabinet,
unplug the unit and have it checked by qualified
personnel before operating it any further.
• Do not drop or place heavy objects on the power
cord. If the power cord is damaged, turn off the
power immediately. It is dangerous to use the unit
with a damaged power cord.
• Unplug the unit from the wall outlet if it is not to be
used for several days or more.
• Disconnect the power cord from the AC outlet by
grasping the plug, not by pulling the cord.
• The socket-outlet shall be installed near the
equipment and shall be easily accessible.
• Use the supplied AC adaptor for the BVM-D9H1U/
D9H1E/D9H1A/D9H5U/D9H5E/D9H5A models
only. It is dangerous to use the AC adaptor for
models other than these.
On installation
• Allow adequate air circulation to prevent internal heat
build-up.
Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation holes.
• Do not install the unit in a location near heat sources
such as radiators or air ducts, or in a place subject to
direct sunlight, excessive dust, mechanical vibration
or shock.
On mounting the rack
When the monitor is mounted on the rack, the
proximity of other equipment or a decrease in air
circulation may cause heat to build up inside the
monitor. Therefore, when mounting the monitor on
the rack, ensure there is an adequate opening for
ventilation or install a fan. The following operating
conditions are needed:
Temperature: 0°C to 35°C (32°F to 95°F),
Optimum temperature: 20°C to 30°C (68°F to 86°F)
On the battery (BVM-D9H1U/D9H1E/D9H1A/
D9H5U/D9H5E/D9H5A only)
The MAIN POWER switch is not supplied with the
above models. Therefore, when the power is turned
off with a battery installed, the monitor is set to
standby mode and a small amount of power is
consumed. When the monitor is not used for a long
period, remove the battery.
On cleaning
To keep the unit looking brand-new, periodically clean
it with a mild detergent solution. Never use strong
solvents such as thinner or benzine, or abrasive
cleansers since they will damage the cabinet. As a
safety precaution, unplug the unit before cleaning it.
On repacking
Do not throw away the carton and packing materials.
They make an ideal container which to transport the
unit.
If you have any questions about this unit, contact your
authorized Sony dealer.
On magnetism
• Do not place the unit near any objects or pieces of
equipment which generate magnetism, such as
magnets, speakers, electric clocks, toys using
magnets, health appliances, etc. Magnetism will
cause picture bounce, oscillations or picture
discoloration.
• Also, the picture may become fuzzy or the colors
may not reproduce correctly due to earth magnetism.
This depends on direction that the unit is installed.
This is not equipment failure. In such a case, simply
degauss the unit.
On the CRT
• Dust accumulates on the CRT easily. Clean the CRT
when necessary with a soft cloth.
The surface of the CRT is easily scratched; therefore,
do not rub or touch the surface of the CRT
unnecessarily since this may result in a scratched
picture tube.
• If you touch the surface of the CRT, you may feel a
weak electrical shock. This is simply static electricity
that is generated on the surface of the CRT. It will not
affect the human body.
On using as the monitor for 4:3 signals
The 16:9 mask is installed at the factory. When the
display is set to the 4:3 aspect ratio, the upper and
lower portions of the display are masked and you
cannot view the upper and lower portions of the
picture. Therefore, when you want to display the
picture in 4:3 aspect ratio, install the supplied 4:3
mask.
3
(E)
Hide quick links:
Advertisement
Table of Contents
