Husqvarna LC 247 Workshop Manual
300 series 200 series
Hide thumbs
Also See for LC 247:
- Operator's manual (460 pages) ,
- Operator's manual (392 pages) ,
- Operator's manual (404 pages)
Related Manuals for Husqvarna LC 247
Summary of Contents for Husqvarna LC 247
- Page 1 Workshop manual LC 247, LC 247S, LC 247SP, LC 347V, LC 347VI, LC 353V, LC 353VI English...
-
Page 2: Table Of Contents
2.2.4 To assemble the mulching-kit .......7 2.3 To do a test run ..............7 2.3.1 To start the engine (LC 247, LC 247S, LC 247SP, LC 347V, LC 253S, LC 353V) ........7 2.3.2 To start the engine (LC 347VI, LC 353VI) .....7 2.3.3 To stop the engine ..........7... -
Page 3: Introduction And Safety Regulations
Introduction and safety regulations 1 Introduction and safety regulations 1.1 General 1.4.1 General safety instructions The service center that repairs the lawn mower must This workshop manual gives a full description of how to have safety devices that comply with local regulations. do troubleshooting, repairs and tests of the lawn mower. -
Page 4: Symbols On The Product
Introduction and safety regulations 1.5 Symbols on the product The product agrees with applicable EC directives. Careless or incorrect use of this product can result in serious or fatal injury to the operator Noise emission to the environment or others. according to the European Community´s Directive. -
Page 5: Delivery And Service
Delivery and service 2 Delivery and service 2.1 Service schedule Descriptions of the maintenance below are found in the operator’s manual. See the engine manual for servicing information for the engine. Daily Maintenance Before use After each use Every 10 hours Every 25 hours Every 100 hours Before storage... -
Page 6: Assembly And Control
Delivery and service 2.2 Assembly and control 2. Move the knobs up in the direction of the handle until they stop and a click is heard. Handle height can be set to 2 different positions, Tighten the knobs fully. 2.2.1 To assemble the handle 1. -
Page 7: To Assemble The Mulching-Kit
2.3.1 To start the engine (LC247, LC 247S, LC 247SP, LC 347V, LC 253S, LC 353V) The models LC 247 and LC 247S have manual choke. 4. Push the start inhibitor to the side. The first time the product is started, press the fuel pump 5 times. -
Page 8: To Do A Test Of The Drive (Lc 247S, Lc 247Sp)
On machines with variable speed, this is adjusted with the control on the left-hand side. 2.3.5 Speed control Examine the maximum engine speed with a Husqvarna original tachometer. Adjust the maximum speed according to the table. Model 2800 ±... -
Page 9: Design And Function
Provide the engine serial number when you send an order for the manual. 3.3 Drive Model Drive system LC 247 Push LC 247S Self propelled LC 247SP Self propelled... -
Page 10: Repair Instructions
Repair instructions 4 Repair instructions WARNING: Before you start any repairs, 5. Attach the washers and the blade screw and tighten stop the engine and remove the ignition with a torque of 70 Nm. cable from the spark plug. Remove the battery on products with electrical start. -
Page 11: To Remove The Front Axle
Repair instructions 4.4 To remove the rear axle (with 4. Unscrew the three screws and lift out the engine. drive) The following procedures applies for both sides: 1. Remove the wheel caps. 5. Unclip the sleeves if necessary. 2. Remove the wheel. 4.3 To remove the front axle 1. - Page 12 Repair instructions 5. Adjust the cutting deck to its highest position by 10. Pull off the link arm and tube as one unit then pressing the button as shown in the illustration. remove the wheel axle. 6. Turn the mower on its side. Use a wooden blocks to 11.
-
Page 13: To Remove The Rear Axle (Without Drive)
Repair instructions 15. Reach through the inspection hole and unhook the 20. Pull out the rear axle with the gearbox. throttle wire 4.5 To remove the rear axle (without 16. Compress the plasic clips and remove the wire. drive) Use bent pliers to pry apart the plastic stops and pull out the rear axle. -
Page 14: To Test The Engine Brake
Repair instructions 4.8 To replace the wires 3. Remove the belt cover for ease of access. 4. Remove the belt. A Engine break wire B Throttle wire C Speed control wire (only in LC 353VI, LC 353V, LC347VI and LC 347V)) E Screw 4.8.1 To change the the engine break wire 1. -
Page 15: To Change The Speed Control Wire
Repair instructions 3. Reach through the inspection hole and unhook the 4. Reach through the inspection hole and unhook the throttle wire from the gearbox. speed control wire from the gearbox. 4. Compress the plasic clips and remove the throttle 5. -
Page 16: To Examine The Spark Plug
Repair instructions 4.11 To adjust the drive belt A flat battery will be fully charged after about 60 minutes. The battery can be quick-charged for shorter periods If the drive feels sluggish, it may be due to a slipping without damage clutch and the clutch cable will then have to be adjusted. -
Page 17: To Clean The Paper Filter
4.12.1 To clean the paper filter Clean the filter by knocking the filter against a flat surface. Never use solvent with petroleum, for example, kerosene, or compressed air to clean the filter. 4.12.2 To clean the foam plastic filter (LC 247, LC 247S, LC 247SP) Remove the foam plastic filter. -
Page 18: Specifications
Specifications 5 Specifications 5.1 Technical data 300 series LC 347V LC 347VI LC 353V LC 353VI Engine Engine manufacturer Briggs & Stratton Briggs & Stratton Briggs & Stratton Briggs & Stratton Cylinder displacement, cm Speed, rpm 2900 2900 2800 2800 Nominal engine output, kW 2.4@2900 2.6@2900... -
Page 19: Technical Data 200 Series
Specifications 5.2 Technical data 200 series LC 247 LC 247S LC 247SP LC 253S Engine Engine manufacturer Briggs & Stratton Briggs & Stratton Briggs & Stratton Briggs & Stratton Cylinder displacement, cm Speed, rpm 2900 2900 2900 2800 Nominal engine output, kW 1.8@2900... - Page 20 115 93 85-26 2017-08-22...