Mounting And Operation - Bosch Rotak 32 LI Original Instructions Manual
Hide thumbs
Also See for Rotak 32 LI:
- Original instructions manual (305 pages) ,
- Original instructions manual (305 pages) ,
- Original instructions manual (23 pages)
Table of Contents
Advertisement
Available languages
Available languages
18 | English
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
05.05.2015
Mounting and Operation
Action
Delivery Scope
Handle Assembly
Snap together the Grassbox
Grassbox fitting/removing
Battery Charging
Inserting the Battery
Insert Isolator Key and fit in the Storage
Position
Adjusting the Cutting Height
Starting
Working Advice
Stopping, Remove the isolator key
Removing the Battery
Blade Maintenance
Selecting Accessories
Starting
For Your Safety
Warning! Switch off, remove the isolator key and the
battery before adjusting, cleaning or if cable is cut,
damaged or entangled.
The blades continue to rotate for a few seconds after
the machine is switched off.
Caution – do not touch the rotating blade.
Battery Charging
Do not use other battery chargers. The supplied battery
charger is designed for the Lithium-Ion battery in your gar-
den product.
Observe the mains voltage! The voltage of the power
supply must correspond with the data given on the name-
plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
The battery is equipped with temperature monitoring that al-
lows charging only in the temperature range between 0 °C
and 45 °C. In this manner, a high battery service life is
achieved.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
F 016 L81 172 | (8.5.15)
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Figure
Page
1
298
2
298
3
299
4
299
5
299
6
300
7
301
8
301
9
302
10
303
11
303
12
304
13
305
14
305
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The "Electronic Cell Protection (ECP)" protects the lithium-
ion battery against deep discharging. When the battery is run
down or discharged, the garden product is shut off by means
of a protective circuit: The blade no longer moves.
Do not continue to press the On/Off
switch after the garden product has
been automatically switched off. The battery can be dam-
aged.
Charging Procedure
The charging procedure starts as soon as the mains plug of
the battery charger is plugged into the socket outlet and the
battery is inserted into the charging compartment .
Due to the intelligent charging method, the charging condi-
tion of the battery is automatically detected and the battery is
charged with the optimum charging current, depending on
battery temperature and voltage.
This gives longer life to the battery and always leaves it fully
charged when kept in the charger for storage.
Rapid-charging Procedure
AL 3640 CV
Professional
AL 3620 CV
Professional
The rapid-charging procedure is indicated by flashing of the
green charge control LED.
Indication element of the battery:
During the charging procedure, the three green LEDs light up
one after the other and briefly go out. The battery is fully
charged when the three green LEDs light up continuously. The
three LEDs go out again approx. 5 minutes after the battery
has been fully charged.
Note: The rapid-charging procedure is only possible when the
battery temperature is within the allowable charging temper-
ature range, see section "Technical Data".
Battery Charged
AL 3640 CV
Professional
AL 3620 CV
Professional
Continuous lighting of the green charge control LED sig-
nals that the battery is fully charged.
Bosch Power Tools
Advertisement
Table of Contents
