Table of Contents
Advertisement
Advertisement
Table of Contents
Troubleshooting
Related Manuals for jcb Hydradig 110W
Summary of Contents for jcb Hydradig 110W
- Page 1 Quick Start Guide Hydradig 110W...
- Page 2 This machine should not be operated by any person who isn’t appropriately qualified or had the appropriate training. > Operation of this machine without periodic maintenance could cause it to malfunction. For more information please contact your JCB Dealer. Please see operator manual for full details.
-
Page 3: Table Of Contents
Start Up Sequence ...........................12 Hydraulic Hitch Unlock ........................13 Shutdown & Auxiliary Venting ......................14 Maintenance Position ........................15 Service / Maintenance ........................16 Access Covers ..........................17-18 Fluids & Lubricants ..........................19 Machine Attachments ........................20 Troubleshooting / FAQs ......................21-22 Your Notes ............................23 HYDRADIG 110W... -
Page 4: Intended Use
Intended Use General > Machine Type – Excavator > Self propelled machine with a wheeled undercarriage > Revolving upper structure with boom, dipper, bucket and slew mechanism Intended Use > Machine intended to be used in normal conditions > With bucket fitted, machine work cycle consists of digging, elevating, slewing and discharging of materials >... -
Page 5: Dimensions
Transport boom height 3132 3305 3437 Transport length 7050 7022 6944 Rear Dozer/No Stabs Dipper lengths 1650 2000 2250 Transport boom height 2399 2796 3065 Transport length 6868 7086 7131 Mass = 10,208kg –11,343kg (please see data plate) HYDRADIG 110W... -
Page 6: Tie Down Points
Tie Down Points Fig 2 Fig 3 Note: These measurements are based on a 2500mm wide trailer bed. The correct tie down positions are identified on the machine by their labels. Measurements ± 100mm. A Angle = 29 ± 1º D Angle = 26 ±... -
Page 7: Lifting Points
The pr s will depend on the condition of the machine and its hydraulic circuits. For this reason your JCB dealer for help and advice before attempting this work. ge the park brake. -
Page 8: Cab Layout & Controls
Cab Switch and Panel Fig 6 A HVAC (Heating Ventilation Air Conditioning) B Ignition switch C Optional switch console D Switch console E Fire extinguisher F Rotary control G Right joystick H Stabiliser controls J Lights and indicators LED (Light Emitting Diode)s K 12V socket and USB port L Instrument panel M Hazard warning light switch... - Page 9 • Eco • Standard • Power (+) Work modes selection Press A to cycle through the work modes Press = Eco Mode – 1600rpm Press twice = Standard Mode – 1800rpm Press again = Power (+) Mode – 2000rpm HYDRADIG 110W...
- Page 10 Switches & Controls Console Switches General Fig 11 The console switches may change according to machine specification. Some a Keypad 1 Each switch has a graphic symbol to show the function of the switch. Before yo A 2 Go K Rear work lights (opt) that you understand its function.
- Page 11 6.2. If the conditions are not met then the machine cannot safely remain in site mode, the switch LED will flash. A check sh HYDRADIG 110W the operator which conditions are not met. The operator can and the check sheet will disappear and allow the machine to...
-
Page 12: Start Up Sequence
Start Up Sequence Operation Insert Isolator Key Dis-arm immobiliser Isolate Machine Safety Equipment About the Product Console Switches Insert isolator key (A) and Key on to position 1 and if Ensure the left arm rest is in Controls Isolation Lever Console Switches Raise the controls isolation lever to isolate the hydraulic controls. -
Page 13: Hydraulic Hitch Unlock
The appropriate status indicator appears on the left side of the display. Auto axle lock structure must be slewed to the straight a HYDRADIG 110W off, machine must be stationary. If these co and the mode indicator at the top left of th... -
Page 14: Shutdown & Auxiliary Venting
Shutdown & Auxiliary Venting Operation Drive Controls Park Machine Apply Foot Brake Secure Machine Service Brake Pedal General Ensure machine slew is central Park machine and apply foot Apply park brake (A) and CAUTION Pressing the brake pedal sharply down will cause the brake to lock on. Take care when using the foot brake while travelling. -
Page 15: Maintenance Position
Isolate the battery to prevent accidental operation of the engine (Page 16, Fig 17-18) nition key. ery to prevent the accidental operation of the engine. k (Operation) (Page 203). HYDRADIG 110W ng tag to the instrument panel to inform other service staff about on-goin... -
Page 16: Service/Maintenance
Service/Maintenance Daily Checks (10h) Operator’s Manual Page Ref. Physical/Visual Tyre pressure check 188-189 Physical Wheel nuts alignment check 186-187 Visual Tow hitch condition check Visual Windscreen washer fluid level check/refill Visual Oil level check 172-173 Physical Fuel level check Visual Coolant quality/level check Visual Coolant or oil leaks check... -
Page 17: Access Covers
Bay Main Fuse Lower Fuses in fuse is installed at the back of the battery bay. The fuses are installed under the tread plate on the front of the chassis. Remove the cover to ge the fuses. Figure 139. HYDRADIG 110W 9831/3350-2... - Page 18 Access Covers Maintenance Cab Panel Service Points Fig 21 G Fuel gauge Maintenance Figure 120. Access Apertures A Cover B Lock C Window washer fill Figure 125. Maintenance Access Apertures A Window washer fluid filler cap over B Lock Figure 121. gine Compartment Cover Engine Compartment Close the cover.
-
Page 19: Fluids & Lubricants
1.9L (x4) JCB Gear Oil HP Plus 4000/2205 Transmission Dropbox 1.0L JCB Gear Oil HP Plus 4000/2205 JCB part numbers are liable to change and may also vary by region. For the latest information, always check with your dealer/distributor. HYDRADIG 110W... -
Page 20: Machine Attachments
Machine Attachments Weight Hydraulic Description Intended Use (kg) Requirements Bucket DP 300mm – 900mm BOT 110-207 General excavation / Bulk loading loose material None Bucket HD 250mm – 900mm 108-210 Heavy Excavation, hard dig, abrasive materials None Bucket GP 250mm – 900mm 98-179 General excavation / Bulk loading loose material None... -
Page 21: Troubleshooting/Faqs
• There is a fault on the keypad • Engine isn’t switched on • If there is an error on the machine and an error code is displayed on the LCD screen –which would inhibit the hydraulics • If none of the above, contact dealer HYDRADIG 110W... -
Page 22: Troubleshooting / Faqs
Troubleshooting/FAQs Issue / FAQ Resolution/Answer My crab steer won’t select after You must use 2WS first in order to re-align the rear axles using 4WS Why has the over speed warning shown The machine has either exceeded 20Kph or 40kph (dependant up on the display on specification). -
Page 23: Your Notes
Your Notes HYDRADIG 110W... - Page 24 They should not therefore be relied upon in relation to suitability for a particular application. Guidance and advice should always be sought from your JCB Dealer’. JCB reserves the right to change specifications without notice. Illustrations and specifications shown may include optional equipment and accessories.