Table of Contents
Advertisement
Quick Links
Form No. 3366-561 Rev B
8, 11, and 14-Blade DPA Reel
Mower
for Greensmaster
®
3300/3400 Series Traction
Units
Model No. 04613—Serial No. 311000001 and Up
Model No. 04614—Serial No. 311000001 and Up
Model No. 04615—Serial No. 311000001 and Up
To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Original Instructions (EN)
Advertisement
Table of Contents
Related Manuals for Toro Greensmaster 3300 Series
Summary of Contents for Toro Greensmaster 3300 Series
- Page 1 Model No. 04613—Serial No. 311000001 and Up Model No. 04614—Serial No. 311000001 and Up Model No. 04615—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or Contents additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Introduction..............2 identifies the location of the model and serial numbers Safety ................ -
Page 3: Safety
Toro replacement parts and • Always wear substantial shoes. Do not operate accessories to keep the Toro all TORO. Never use cutting units while wearing sandals, tennis shoes, "will-fit" replacement parts and accessories sneakers or shorts. -
Page 4: Setup
Setup Media and Additional Parts Description Qty. Operator’s Manual Read before installing and operating cutting unit Parts catalog Use to reference part numbers Certification of compliance Save for future reference Installing the Front Roller No Parts Required Procedure g014596 The cutting unit is shipped without a front roller. Install Figure 3 the roller using the loose parts supplied with the cutting 1. -
Page 5: Adjusting The Rear Roller
Should excessive reel drag be evident, it will be either necessary to backlap or regrind the cutting unit to achieve the sharp edges needed for precision cutting (refer to the Toro Reel Sharpening Manual). g014595 Figure 4 1. Bedbar adjusting screw Adjusting the Rear Roller 2. -
Page 6: Adjusting The Height Of Cut
Figure 7 1. Sideplate mounting flange 3. Roller bracket 2. Spacer To adjust rear roller proceed as follows: 1. Raise the rear of the cutting unit and place a block under the bedknife. Figure 8 1. Sideplate mounting bolts 2. Remove the 2 nuts securing each roller bracket and spacer to each sideplate mounting flange. -
Page 7: Adjusting The Cut-Off Bar
3. Hook the screw head onto the cutting edge of the Recommended Bedknife/Height of Cut Chart (cont'd.) bedknife and rest the rear end of the bar onto the Extended 108-4303 0.062–0.188 inch rear of the roller (Figure 11). Micro-cut (1.5–4.7 mm) (Optional) Extended 108-4302... - Page 8 g014643 Figure 12 1. Cut-off bar 2. Insert a 0.060 inch feeler gauge between the top of the reel and the bar and tighten the screws. Ensure that the bar and reel are equal distance apart across the complete reel. Note: The bar is adjustable to compensate for changes in turf conditions.
-
Page 9: Product Overview
A selection of Toro approved attachments and accessories are available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. -
Page 10: Operation
Operation bedknife. If a file is occasionally run across the front edge to remove this burr, improved cutting can be obtained. Note: Determine the left and right sides of the After extended running, a ridge will eventually machine from the normal operating position. develop at both ends of the bedknife. -
Page 11: Maintenance
Maintenance stamped steel washers on each end of the bedbar (Figure 15). Note: Determine the left and right sides of the machine from the normal operating position. Servicing the Bedbar Removing the Bedbar 1. Turn the bedbar adjusting screw, counterclockwise, to back the bedknife away from the reel (Figure 13). -
Page 12: Backlapping The Reel
Note: Additional instructions and procedures on Backlapping are available in the Toro Sharpening Reel and Rotary Mowers Manual, Form No. 80-300PT. Note: For a better cutting edge, run a file across... - Page 13 Notes:...
- Page 14 Notes:...
- Page 15 Notes:...
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.