Advertisement
Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SafeTy
1.1.
General SafeTy
warninG! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
warninG! do noT aim the laser beams at your or another person's or animal's eye and beware of reflections from mirrors or other
‰
shiny surfaces.
Remove the battery from the saw before changing blades, servicing or performing any maintenance.
9
Maintain the saw in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and use recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Keep the saw clean and the blade sharp for best and safest performance.
9
Wear approved safety eye protection (standard spectacles are not adequate) and dust mask.
9
Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use in a suitable work area. Keep area clean, tidy and free from unrelated materials. ensure there is adequate lighting.
9
ensure locking hex. key is removed from the blade clamp flange before starting saw.
9
evaluate your work area before using the saw e.g. partitions may conceal electric cables or water piping.
9
Secure non-stable workpiece with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Before making a cut ensure that all accessories and adjustment fixings are fully tightened.
9
only use saw blades that are specifically designed for use with this machine.
9
Always use the side fence supplied or a securely fixed straight edge guide when doing a rip cut (along the length of the grain).
9
When not in use store in a safe, dry, childproof area .
9
do noT use the saw where there are flammable liquids, solids or gases such as paint solvents, etc.
8
do noT allow children to operate the saw.
8
do noT operate the saw if any parts are missing as this may cause failure and/or personal injury.
8
do noT leave the saw operating unattended.
8
do noT carry the saw with your finger on the power switch.
8
do noT use the saw for a task it is not designed to perform.
8
do noT use a blade which is damaged, cracked, distorted or has missing teeth.
8
do noT tamper with, or remove, blade guard.
8
do noT operate the saw when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
do noT get the saw wet or use in damp or wet locations.
8
do noT hold unsecured workpiece in your hand whilst cutting.
8
do noT force the saw to cut but allow it to operate at its normal working speed.
8
do noT use the saw with any other manufacturers' accessories.
8
do noT reach under the workpiece whilst the blade is cutting. Keep hands away from the cutting area and do not attempt to remove
8
cut material whilst the blade is still turning.
do noT wedge the blade guard open.
8
do noT fit or use a saw blade that is intended to cut metal. Always ensure that the saw is fitted with the correct wood cutting blade.
8
do noT substitute an abrasive wheel for the saw blade.
8
do noT allow the blade to come into contact with nails or other steel fixings used in old timber or existing timber structures. Inspect the
8
workpiece before commencing cutting and remove any potential hazards.
do noT attempt to stop the saw by pressing on the side of the blade.
8
do noT start the saw with the blade in contact with the workpiece. Allow the blade to run up to speed before proceeding to cut.
8
1.2.
laSer SafeTy
warninG! do noT look or stare into the laser beam as permanent eye damage could result.
‰
The CP20VCS utilises a Class II laser that emits low levels of visible radiation (i.e. wavelengths between 400 and 700 nanometres)
which are safe for the skin but not inherently safe for the eyes. The Class II emission limit is set at the maximum level for which eye
protection is normally afforded by natural aversion responses to bright light.
© Jack Sealey limited
20V CirCular Saw Ø150mm - Body only
Model no:
Wear protective
Wear safety
gloves
footwear
Original Language Version
CP20VCS
Wear protective
Wear ear
clothing
protection
Warning!
Wear
laser beam
dust mask
CP20VCS Issue 1 17/09/19
Advertisement
Table of Contents
Related Manuals for Sealey CP20VCS
Summary of Contents for Sealey CP20VCS
- Page 1 ‰ The CP20VCS utilises a Class II laser that emits low levels of visible radiation (i.e. wavelengths between 400 and 700 nanometres) which are safe for the skin but not inherently safe for the eyes. The Class II emission limit is set at the maximum level for which eye protection is normally afforded by natural aversion responses to bright light.
-
Page 2: Specification
Always use blades with the correct size and shape (diamond versus round) of arbour holes. Blades that do not match the ‰ the mounting hardware of the saw will run eccentrically, causing loss of control. 4.2.1. Fully depress the spindle lock button (fig.1) and use the supplied hex key to undo the socket head cap screw holding the outer flange (fig.1) in situ. Remove the screw and outer flange. 4.2.2. Pull the blade guard back using the lever (fig.1) and carefully lift the blade off the spindle and withdraw it out from the housing. Original Language Version CP20VCS Issue 1 17/09/19 © Jack Sealey limited... - Page 3 Be aware of the time it takes for the blade to stop after the switch is released. Parallel guide Guide clamp thumb Bevel angle thumb screw screw fig.2 Original Language Version CP20VCS Issue 1 17/09/19 © Jack Sealey limited...
-
Page 4: Maintenance
Clean the saw with a dry cloth and remove sawdust from ventilation slots. Original Language Version CP20VCS Issue 1 17/09/19 © Jack Sealey limited... -
Page 5: Weee Regulations
Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson way, Suffolk Business Park, Bury St edmunds, Suffolk. iP32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...