hit counter script
Sony STR-DN1080 Service Manual

Sony STR-DN1080 Service Manual

Multi channel av receiver
Hide thumbs Also See for STR-DN1080:
Table of Contents

Advertisement

2020/11/17 21:24:35 (GMT+09:00)
STR-DN1080/ZA810ES
SERVICE MANUAL
Ver. 1.3 2020.11
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus aff ected unit was found during
service, contact your Service Headquarters.
(STR-DN1080)
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(USA models only)
With 6 ohm loads, both channels driven, from
20 Hz – 20,000 Hz; rated 100 watts per
channel minimum RMS power, with no more
than 0.09% total harmonic distortion from
250 milliwatts to rated output.
Amplifier section
Minimum RMS Output Power
(6 ohms, 20 Hz – 20 kHz, THD 0.09%)
100 W + 100 W
Stereo Mode Output Power
(6 ohms, 1 kHz, THD 0.9%)
120 W + 120 W
Surround Mode Output Power
(6 ohms, 1 kHz, THD 0.9%)
165 W per channel
1)
Measured under the following conditions:
Area
USA, Canada, Taiwan
Oceania, Europe
2)
Reference power output for front, center,
surround and surround back speakers. Depending
on the sound field settings and the source, there
may be no sound output.
Frequency response
Analog
10 Hz – 100 kHz, +0.5/–2 dB (with sound
field and equalizer bypassed)
Input
Analog
Sensitivity: 500 mV/50 kilohms
S/N
Digital (Coaxial)
Impedance: 75 ohms
S/N: 100 dB (A, 20 kHz LPF)
Digital (Optical)
S/N: 100 dB (A, 20 kHz LPF)
Output (Analog)
ZONE 2
Voltage: 2 V/1 kilohm
SUBWOOFER
Voltage: 2 V/1 kilohm
Equalizer
Gain levels
±10 dB, 1 dB step
3)
INPUT SHORT (with sound field and equalizer
bypassed).
4)
Weighted network, input level.
9-896-382-04
2020K33-1
©
2020.11
FM tuner section
Tuning range
USA and Canadian models:
87.5 MHz – 108.0 MHz (100 kHz step)
Other models:
87.5 MHz – 108.0 MHz (50 kHz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Video section
1)
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
HDMI Video
Resolution
480p/60 Hz
2)
576p/50 Hz
720p/60 Hz, 50 Hz, 30 Hz, 24 Hz
1080i/60 Hz, 50 Hz
1080p/60 Hz, 50 Hz, 30 Hz, 25 Hz, 24 Hz
4K/60 Hz*, 50 Hz*, 30 Hz, 25 Hz, 24 Hz
* VIDEO 1 supports YCbCr 4:2:0 8 bit only
Power requirements
Support
120 V AC, 60 Hz
HDCP2.2, HDR (HDR10, Hybrid Log-Gamma,
230 V AC, 50 Hz
Dolby Vision), 3D, Deep Color, ITU-R
BT.2020, eARC/ARC
iPhone/iPad/iPod section
BLUETOOTH technology works with iPhone 7,
iPhone 7 Plus, iPhone SE, iPhone 6s, iPhone 6s
Plus, iPhone 6, iPhone 6 Plus, iPhone 5s, iPhone
5c, iPhone 5, iPhone 4s, and iPod touch (5th and
6th generation.)
AirPlay works with iPhone, iPad, and iPod touch
with iOS 4.3.3 or later, Mac with OS X Mountain
Lion or later, and PC with iTunes 10.2.2 or later.
3)
4)
: 105 dB (A, 500 mV
)
You can use "SongPal" app with this receiver via
BLUETOOTH or network connection.
iPhone/iPad/iPod playback via (USB) port is
not possible.
USB section
(USB) port:
Type A (For connecting USB flash drive)
Maximum current
1 A
Network section
Ethernet LAN
100BASE-TX
Wireless LAN
Compatible standards:
IEEE 802.11 a/b/g/n
Security:
WPA/WPA2-PSK, WEP
Radio frequency:
2.4 GHz, 5 GHz
Sony Home Entertainment &
Sound Products Inc.
Photo: STR-DN1080
SPECIFICATIONS
BLUETOOTH section
Communication system
BLUETOOTH Specification version 4.1
Output
BLUETOOTH Specification Power Class 1
Maximum communication range
Line of sight approx. 30 m (98.4 feet)
Frequency band
2.4 GHz band (2.4000 GHz – 2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH profiles
A2DP 1.2 (Advanced Audio Distribution
Profile)
AVRCP 1.5 (Audio Video Remote Control
Profile)
3)
Supported Codecs
4)
SBC
, AAC, LDAC
Transmission range (A2DP)
20 Hz – 40,000 Hz (LDAC sampling
frequency 96 kHz with 990 kbps
transmission)
20 Hz – 20,000 Hz (Sampling frequency
44.1 kHz)
1)
The actual range will vary depending on factors
such as obstacles between devices, magnetic
fields around a microwave oven, static electricity,
cordless phone, reception sensitivity, antenna's
performance, operating system, software
application, etc.
2)
BLUETOOTH standard profiles indicate the
purpose of BLUETOOTH communication between
devices.
3)
Codec: Audio signal compression and conversion
format
4)
Subband Codec
General
Power requirements
Area
Power requirements
USA, Canada, Taiwan
120 V AC, 60 Hz
Oceania
230 V AC, 50 Hz
Europe
230 V AC, 50/60 Hz
Operating frequency and maximum output
power (for European models)
Wireless LAN/BLUETOOTH
Operating
Maximum output
frequency
power
2400 - 2483.5 MHz
≤ 20.0 dBm
MULTI CHANNEL AV RECEIVER
US Model
Canadian Model
STR-DN1080/ZA810ES
AEP Model
UK Model
Australian Model
Taiwan Model
Wireless LAN
Operating
Maximum output
frequency
power
5150 - 5250 MHz
≤ 23.0 dBm
5250 - 5350 MHz
≤ 20.0 dBm
5470 - 5725 MHz
≤ 20.0 dBm
1)
5725 - 5850 MHz
≤ 14.0 dBm
NFC
Operating
Maximum output
2)
frequency
power
13.56 MHz
< 60 dBμA/m at 10 m
Power consumption
240 W
European models
Standby mode: 0.4 W
(When [Control for HDMI], [Standby
Through], [Bluetooth Standby], and all
zone power are set to [Off].)
Bluetooth Standby mode: 1.5 W
(When [Bluetooth Standby] is set to
[On], and [Control for HDMI], [Standby
Through], and all zone power are set to
[Off].)
Networked standby (all wired network
ports are connected, all wireless
network ports are activated): 1.5 W
Other models
Standby mode: 0.4 W
(When [Control for HDMI], [Standby
Through], [Remote Start], [Bluetooth
Standby], [Network Standby], and all
zone power are set to [Off].)
Bluetooth Standby mode: 2.5 W
(When [Bluetooth Standby] is set to
[On], and [Control for HDMI], [Standby
Through], [Remote Start], [Network
Standby], and all zone power are set to
[Off].)
Dimensions (width/height/depth) (Approx.)
430 mm × 156 mm × 331 mm (17 in ×
6 1/4 in × 13 1/8 in) including projecting
parts and controls
Mass (Approx.)
9.1 kg (20 lb 1 oz) (USA, Canadian and
Taiwan models)
9.7 kg (21 lb 6 oz) (European and Oceanian
models)
Supplied Accessories
Remote control (1)
R03 (size AAA) batteries (2)
FM wire antenna (aerial) (1)
Calibration microphone (1)
Design and specifications are subject to change
without notice.
– Continued on next page –
STR-DN1080
SYS SET

Advertisement

Table of Contents
loading

Summary of Contents for Sony STR-DN1080

  • Page 1 Wireless LAN Compatible standards: – Continued on next page – IEEE 802.11 a/b/g/n Security: WPA/WPA2-PSK, WEP Radio frequency: MULTI CHANNEL AV RECEIVER 2.4 GHz, 5 GHz 9-896-382-04 Sony Home Entertainment & 2020K33-1 Sound Products Inc. © 2020.11 SYS SET...
  • Page 2 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES (STR-DN1080) Playable types of audio files Supported digital audio formats The digital audio formats that this receiver can decode depend on the digital audio output jacks Codec Extension of the connected device. This receiver supports the following audio formats. The words in brackets are those indicated on the display panel.
  • Page 3 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES (STR-ZA810ES) AUDIO POWER SPECIFICATIONS Supported video formats Playable types of audio files Codec Extension POWER OUTPUT AND TOTAL HARMONIC DISTORTION: Over-Under MP3 (MPEG-1 Audio Layer III) .mp3 Format Frame Side-by- With 6 ohm loads, both channels driven, from 20 Hz – 20,000 Hz; rated...
  • Page 4 Bluetooth SIG, Inc. in the United States and/or other screws, and all other exposed metal parts for AC leakage. Inc. and any use of such marks by Sony countries. © DTS, Inc. All Rights Reserved. Corporation is under license. Other trademarks Check leakage as described below.
  • Page 5: Table Of Contents

    2-22. FRONTJACK Board, POWERKEY Board, 7-2. MB-1613 Board Section ..........84 DISPLAY Board ............. 28 7-3. Power Supply Section (STR-DN1080) ......85 2-23. NFC-ICON Board, NFC Module ........29 7-4. Power Supply Section (STR-ZA810ES) ......86 2-24. BTW Board ..............29 7-5.
  • Page 6 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 SECTION 1 SERVICING NOTES The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit. UNLEADED SOLDER CHANGE OF MB-1613 BOARD Boards requiring use of unleaded solder are printed with the lead- The MB-1613 board has been changed in the midway of produc- free mark (LF) indicating the solder contains no lead.
  • Page 7 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES NOTE OF REPLACING THE MB-1613 BOARD OR Diag WLAN/BT COMBO CARD Category: Bluetooth Device Test When the MB-1613 board or WLAN/BT combo card is replaced, be sure to perform with referring to the following item. Diag Category: Bluetooth Device Test •...
  • Page 8 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES NETWORK CONNECTION CHECKING METHOD 2. Checking method of wired LAN connection When replacing the following parts, be sure to check the connec- tion of wireless LAN and wired LAN. Necessary equipment: • TV monitor Relevant part: • Router •...
  • Page 9 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES NFC CONNECTION CHECKING METHOD NOTICE OF MAC ADDRESS CHANGE TO CUSTOM- When repairing or replacing the following parts, be sure to check the NFC connection. When the MB-1613 board or WLAN/BT combo card is replaced, the MAC address has been changed.
  • Page 10 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES NOTE OF REPLACING THE IC ON THE DCDC BOARD BOND FIXED POSITION OF ELECTRICAL PARTS When replacing the IC on the DCDC board, remove the earth wire When the parts that fi xed on the board by the bond have been re- that connected to the DCDC board, and it is necessary to install moved, fi...
  • Page 11 After checking the above items and fixing any problems, plug in the AC power cord (mains lead) and turn on the receiver. If the problem persists, consult your nearest Sony dealer. [Overload occurred.] appears on the TV screen.
  • Page 12: Disassembly

    2-28. DCDC BOARD SERVICE POSITION (SIDE B) (Page 31) 2-5. MODULE BRACKET ASSY (Page 16) 2-6. RS232C BOARD (STR-ZA810ES) 2-17. AC INLET (STR-ZA810ES) 2-18. POWER CORD (STR-DN1080) (Page 16) (Page 24) (Page 25) 2-7. MB-1613 BOARD BLOCK-1 (Page 17) 2-8. MB-1613 BOARD BLOCK-2 (Page 18) 2-10.
  • Page 13: Case (Entry), Fuse

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Note: Follow the disassembly procedure in the numerical order given. 2-2. CASE (ENTRY), FUSE 2 three screws (BVTP3 1 three screws (B-TYPE4 1 three screws (B-TYPE4 fuse DCDC board rear side 7 case (entry) left side 8 fuse STANDBY board –...
  • Page 14: Dual-Band Dipole Antenna

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 2-3. DUAL-BAND DIPOLE ANTENNA 4 Rotate the claw of antenna cushion (R) connector (No. 2) rear side holder in the direction of the arrow, align the hole of back panel. top side – Inner view –...
  • Page 15: Wlan/Bt Combo Card

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-4. WLAN/BT COMBO CARD Note 1: When the WLAN/BT combo card is replaced, refer to “NOTE OF REPLACING THE MB-1613 BOARD OR WLAN/BT COMBO CARD” on page 7. No. 1 WLAN/BT combo card 2 coaxial harness connector (No. 1)
  • Page 16: Module Bracket Assy

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-5. MODULE BRACKET ASSY 4 module bracket assy Note: When installing the module bracket assy, 3 radiation align the two bosses and two holes. sheet 1 three screws module bracket assy (BVTP3 – – rear side boss boss...
  • Page 17: Mb-1613 Board Block-1

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-7. MB-1613 BOARD BLOCK-1 • Continued on 2-8 (page 18). Note 4: During reassembly, use new cable ties Note 1: The cables must not touch the heat sink. to fasten the wires back in place as Note 2: Make sure that the sleeve ferrite clamp does not they were before disassembly.
  • Page 18: Mb-1613 Board Block-2

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 2-8. MB-1613 BOARD BLOCK-2 4 MB-1613 board block 2 screw Note 1: When installing the MB-1613 board block, (BVTP3 align the two ribs and two holes. 1 eight screws 2 screw (See Note 2) 3 Remove the MB-1613 board block 2 screw in the direction of the arrow.
  • Page 19: Dcdc Board Block

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-10. DCDC BOARD BLOCK saranet cushion rear side rear side GND BRACKET board cable tie – – lead pin MAIN board 8 DCDC board block Note 1: When installing the DCDC COAX board board block, align the two 1 saranet bosses and two holes.
  • Page 20: Power Transformer

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-11. POWER TRANSFORMER Attach in order from 1 to 4. 30 mm 3 Lock the claw. 1 sleeve ferrite clamp power 2 Wrap the cable around. 4 cushion (R) transformer front side 2 sleeve ferrite clamp 1 cushion (R) 3 Cut the cable tie.
  • Page 21: Back Panel Block

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 2-12. BACK PANEL BLOCK front side Note 1: During reassembly, use new cable ties to fasten the wires back in place as they were before disassembly. 6 claw 7 back panel block 3 five screws (BVTP3...
  • Page 22: Main Board Block

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-13. MAIN BOARD BLOCK 6 saranet (sound) to MB-1613 board 5 FFC 22P terminal side (CN1003) guide line 6 saranet (center) terminal 1 connector (sound) side (CN1393) 7 two screws The opposite side 2 connector (BVTP3 is terminal side.
  • Page 23: Main Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-14. MAIN BOARD 3 heat sink block front side 4 MAIN board 1 Remove forty-two solders. rear side 2 screw 2 screw (BVTP3 (BVTP3 bottom side 2-15. STANDBY BOARD 2 three screws 4 label fuse (T.L) (BV3) lead pin 1 Remove the cable from the lead pin.
  • Page 24: Dcdc Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-16. DCDC BOARD 3 sleeve ferrite clamp 2 cushion (R) 5 screw (BVTP3 rear side Note 2: During reassembly, use new cable ties 4 connector to fasten the wires back in place as (CN1906) they were before disassembly.
  • Page 25: Power Cord (Str-Dn1080)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 2-18. POWER CORD (STR-DN1080) front side Note: During reassembly, use new cable ties to fasten the wires back in place as they were before disassembly. CNP901 rear side Press. 4 Draw the power cord 2 power cord block out of the hole.
  • Page 26: Front Panel Block

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 2-19. FRONT PANEL BLOCK groove Note 1: During reassembly, use new cable ties • Wire setting to fasten the wires back in place as they were before disassembly. heat sink 1 Cut the cable tie. cable tie...
  • Page 27: Volume Knob, Menu Knob

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-21. VOLUME KNOB, MENU KNOB Note: The menu knob can be removed even without removing the vol- ume knob. How to install the volume knob or menu knob When installing the volume knob or menu knob to the rotary encoder, align the directions of the D-shaped tip of the rotary encoder and the D-shaped notch at the inner side of the volume knob or menu knob.
  • Page 28: Frontjack Board, Powerkey Board, Display Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-22. FRONTJACK BOARD, POWERKEY BOARD, DISPLAY BOARD Note 1: When the DISPLAY board is repaired, refer to “NFC CON- NECTION CHECKING METHOD” on page 9. guide line (center) saranet (sound) to NFC module to DISPLAY board FFC 7P...
  • Page 29: Nfc-Icon Board, Nfc Module

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-23. NFC-ICON BOARD, NFC MODULE Note 1: When the NFC-ICON board is repaired or the NFC mod- ule is replaced, refer to “NFC CONNECTION CHECKING METHOD” on page 9. front panel block 4 claw boss 5 Remove the NFC module block 4 claw in the direction of the arrow.
  • Page 30: Main Board Service Position (Check The Side A Removing The Back Panel)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-25. MAIN BOARD SERVICE POSITION (Check the SIDE A removing the back panel) alligator clip Clamp to the HDMI connector (CN5000). (“GAME” port) MB-1613 board front panel block top side Clamp to the GND plate. alligator clip Clamp to the GND plate.
  • Page 31: Mb-1613 Board Service Position (Side B)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2-27. MB-1613 BOARD SERVICE POSITION (SIDE B) insulating sheet MB-1613 board top side front side DCDC board Clamp to the HDMI connector (CN5000). (DN1080) (“GAME” port) alligator clip Clamp to the GND plate. (ZA810ES) insulating sheet GND BRACKET board Clamp to the chassis.
  • Page 32: Test Mode

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES SECTION 3 TEST MODE SOUND FIELD CLEAR MODE 3. User Initialize The preset sound fi eld is cleared when this mode is activated. Initialize user setting. Procedure: Procedure: 1. While pressing the [MUSIC] button, press the [ ] button to 1.
  • Page 33 (When [B] button on the remote commander is pressed, return to the special menu list) When [b] button on the remote commander is pressed, the following message is appears. N108 UCA : STR-DN1080: US and CND models N108 CEL STR-DN1080: AEP and UK models Model & Destination check M O D &...
  • Page 34 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Items Display Remark When [b] button on the remote commander is pressed, the following message is appears. “SOURCE” : normal mode, “MIC” : mode that output audio to the speaker from microphone MIC check input Each time [V]/[v] button on the remote commander is pressed, it changes “SOURCE”...
  • Page 35 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.2 HISTORY MODE The state that the set is used to be memorized. Procedure: 1. While pressing the [SPEAKERS] and [DISPLAY MODE] buttons, press the [ ] button to turn the power. 2. The message “HISTORY” appears.
  • Page 36 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 SOFTWARE VERSION DISPLAY MODE KEY CHECK MODE The model, destination and software version are displayed Each button can be checked. Procedure: Procedure: 1. While pressing the [2CH/MULTI] and [PURE DIRECT] but- 1. While pressing the [SPEAKERS] and the [PURE DIRECT] tons, press the [ ] button to turn the power.
  • Page 37 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES SIRCS DISABLE MODE HDMI SPECIAL MENU: MODE 2 The SIRCS signal of the remote commander which this unit re- When DTS:X can not be outputted due to some problem, it can be ceives can be disabled. returned to EDID that supports standard DTS:X.
  • Page 38 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES MTK SERVICE MODE Note: The operation in this mode must a TV monitor and supplied remote commander. Setting method of the service mode: 1. Connect this unit with TV monitor. 2. Press the [ ] button to turn the power on.
  • Page 39 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 2. Menu Tree Service Mode Menu Device Test Diag Service Mode Menu [1] Diag [1] Diag [2] Log [2] Log [3] Factory Initialize [3] Factory Initialize [4] Network [4] Network Video Test [5] Version Up [5] Version Up...
  • Page 40 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 3. Service Mode Menu (Top Menu) 4. Diag (Device Test) This is the top menu of MTK service mode. This screen is used for test of each devices mounted on the board. Each function is accessed from this screen.
  • Page 41 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 7. Diag (Wireless LAN Test) Diag This screen performs wireless LAN/Miracast test. Category: Wireless LAN Test Screen 1: Selects the wireless LAN test category Operation: Diag [B]/[b] Selects the category Category: Wireless LAN Test [v]/[ ] Moves to the selected category...
  • Page 42 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 11. Diag (Bluetooth Device Test) Diag This screen performs Bluetooth device test. Category: Bluetooth Device Test Screen 1: Selects the Bluetooth device test category Operation: Diag [B]/[b] Selects the category Category: Bluetooth Device Test [v]/[ ] Moves to the selected category...
  • Page 43 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 13. Factory Initialize (Factory Settings) 16. System Information (System Information Display) Return all of the unit setting to their factory defaults. This screen displays system information. (When the initialize is completed, the power turns off automati- cally) Screen 1: Basic Information...
  • Page 44: Electrical Check

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES SECTION 4 ELECTRICAL CHECK 0 dB = 1 V TUNER SECTION FM AUTO STOP CHECK signal generator unit Procedure: 1. Press the [ ] button to turn the power on. 2. Input the following signal from signal generator to FM antenna input directly.
  • Page 45: Troubleshooting

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES SECTION 5 TROUBLESHOOTING Flow of repair (when sound is not outputted) START The “PROTECTOR” Check that FFCs between is not displayed on MB-1613 board and MAIN the display panel. board are connected certainly. Check completed The voltage of the following Check the surrounding circuit pin is 2.8 V.
  • Page 46 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES – From the page 45 – – From the page 45 – NG Check the surrounding circuit, Measure the power amplifier circuit (each channel and replace the defective parts. (FL/FR/SL/SR/SBL/SBR/C) on the MAIN board) with a tester, and check the following things.
  • Page 47 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES – From the page 46 – – From the page 46 – The data is outputted from the Replace the MB-1613 board. following pins. MB-1613 board: CN8000 pin 2, 3, 5, 6, 8 ,9, 11, 12 CN8003 pin 2, 3, 5, 6, 8 ,9, 11, 12...
  • Page 48 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES MEMO SYS SET...
  • Page 49: Diagrams

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM - MEMORY/USB/LAN Section - SD-RAM MTK_L/R, MTK_SL/SR, MTK_C/SW, IC102 MTK_SBL/SBR, MTK_2ND_L/R, MTK_BCLK, MTK_LRCK MTK_L/R DQL0 – DQL7, >003B (Page 52) RDQ0 – RDQ15 AOSDATA0 DQU0 – DQU7 IC101 (1/4) MTK_SL/SR AOSDATA1 MTK_C/SW A0 –...
  • Page 50: Block Diagram - Hdmi Section (1/2)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-2. BLOCK DIAGRAM - HDMI Section (1/2) - HDMI REPEATER IC5004 (1/2) HDMI RECEIVER IC3503 P1TX0P 87 P2RX0P DATA0+ 97 P0RX0P P1TX0M 86 P2RX0M DATA0– 96 P0RX0M P1TX1P 90 P2RX1P DATA1+ 100 P0RX1P P1TX1M 89 P2RX1M DATA1– 99 P0RX1M...
  • Page 51: Block Diagram - Hdmi Section (2/2)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-3. BLOCK DIAGRAM - HDMI Section (2/2) - CN5003 HDMI [4K] [HDCP 2.2] HDMI SWITCH HDMI REPEATER (TV) OUT A IC5001 IC5004 (2/2) IC101 (2/4) CH0_P 42 D0+_1 D0+_SINK 141 P0RX0P P0TX2M DATA0+ CH0_M 41 D0–_1 D0–_SINK 140 P0RX0M P0TX2P DATA0–...
  • Page 52: Block Diagram - Digital Audio Selector Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-4. BLOCK DIAGRAM - DIGITAL AUDIO SELECTOR Section - MTK_L/R, MTK_SL/SR, MTK_C/SW, MTK_SBL/SBR, MTK_2ND_L/R, SIGNAL PATH MTK_BCLK, MTK_LRCK >003B : AUDIO HDMI DATA SELECTOR (Page 49) IC5506 MTK_LRCK HDMI_SD0, HDMI_SD1, HDMI_SD2, 2 1A HDMI_SD3, HDMI_BCK, HDMI_LRCK, MTK_2ND_L/R 3 1B...
  • Page 53: Block Diagram - Digital Audio Section (1/2)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-5. BLOCK DIAGRAM - DIGITAL AUDIO Section (1/2) - (Page 55) DSD_NATIVE_BCLK >016B DSD_NATIVE_SL DSD_NATIVE_FL, DSD_NATIVE_FR, DSD_NATIVE_SL, DSD_NATIVE_SR DSD_NATIVE_SR, DSD_NATIVE_C, DSD_NATIVE_SW, DSD_NATIVE_BCLK DSD_NATIVE_FR DSD_NATIVE_SW DSD_NATIVE_C HDMI_MTK_SD0, HDMI_MTK_SD1, DSD_NATIVE_FL A/D CONVERTER, HDMI_MTK_SD2, HDMI_MTK_SD3, DIGITAL AUDIO INTERFACE RECEIVER DSP1 DSP2...
  • Page 54: Block Diagram - Digital Audio Section (2/2)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-6. BLOCK DIAGRAM - DIGITAL AUDIO Section (2/2) - DSP3 L/R2_OUT, SL/SR2_OUT, C/SW2_OUT, LR3_OUT, SL/SR3_OUT, IC7501 ZONE_L/R2_OUT, L/R_EXT1_OUT, L/R_EXT2_OUT, C/SW3_OUT, LR_EXT1_3_OUT, L/R_EXT3_OUT, BCLK2_OUT, LRCLK2_OUT BCLK3_OUT, LRCLK3_OUT L/R2_OUT LR3_OUT >017B >020B L/R2_IN L/R3_OUT (Page 53) (Page 55) SL/SR2_OUT SL/SR3_OUT...
  • Page 55: Block Diagram - Analog Audio Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-7. BLOCK DIAGRAM - ANALOG AUDIO Section - J1100 R-CH L_IN MIC AMP >015B CALIBRATION MIC INL1 ADCL 56 IC1100 (Page 53) FL, SL, SBL, C, Z2-PREOUT-SW-RY J1401 (1/3) >024B OUTFL 9 INL6 (Page 56) SAT/CATV OUTSL 13...
  • Page 56: Block Diagram - Amp Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 6-8. BLOCK DIAGRAM - AMP Section - –2 R-CH J1101 PHONES RELAY DRIVE RY1390 Q1375 TB1501 –2 BOOSTER Q1700 POWER AMP – LIMITER CURRENT Q1720, 1722, RELAY DRIVE FL, SL, SBL, C, Q1702, 1703 DETECT RY1350...
  • Page 57: Block Diagram - Video/Panel Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-9. BLOCK DIAGRAM - VIDEO/PANEL Section - ND1100 VACUUM SYSTEM CONTROLLER FLUORESCENT IC3002 (9/10) DISPLAY VIDEO INPUT SELECTOR, VIDEO AMP IC1232 FL_DATA SI/DATA J1401 (2/3) J1401 (3/3) FL_CLK VIDEO VIDEO 1 VIN3 VOUT 8 FL_LAT MONITOR OUT FL_BK...
  • Page 58: Block Diagram - Power Supply Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-10. BLOCK DIAGRAM - POWER SUPPLY Section - DADCDC_4.5V DC/DC 5V_PWR_CNT1 CONVERTER >010B +3.3V IC1911 +3.3V REGULATOR (Page 51) (FOR IC6000) IC6021 +3.3V P_CONT3 >001B DSP_3.3V REGULATOR IC6505 (Page 49) +3.3V DA_3.3V REGULATOR USB_PCONT >026B IC318 (Page 57) +1.1V...
  • Page 59 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) • Circuit Boards Location For Printed Wiring Boards. For Schematic Diagrams. WLAN/BT combo card Note:...
  • Page 60: Printed Wiring Board - Mb-1613 Board (Side A) (Type-11)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-11. PRINTED WIRING BOARD - MB-1613 Board (Side A) (Type-11) - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. HDMI 4K HDCP 2.2 (TV) OUT B/ OUT A HDMI (for AUDIO)
  • Page 61: Printed Wiring Board - Mb-1613 Board (Side B) (Type-11)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-12. PRINTED WIRING BOARD - MB-1613 Board (Side B) (Type-11) - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. IR REMOTE J3190 J3191 MB-1613 BOARD (SIDE B) (Type-11) CL3075 CL3077 CL3071...
  • Page 62: Mb-1613 Board (Side A) (Type-21)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-13. PRINTED WIRING BOARD - MB-1613 Board (Side A) (Type-21) - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. HDMI 4K HDCP 2.2 (TV) OUT B/ OUT A HDMI (for AUDIO)
  • Page 63: Printed Wiring Board - Mb-1613 Board (Side B) (Type-21)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-14. PRINTED WIRING BOARD - MB-1613 Board (Side B) (Type-21) - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. IR REMOTE J3190 J3191 MB-1613 BOARD (SIDE B) (Type-21) CL3075 CL3077 CL3071...
  • Page 64: Printed Wiring Board - Main Board (Component Side)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-15. PRINTED WIRING BOARD - MAIN Board (Component Side) - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. ANTENNA MAIN BOARD (COMPONENT SIDE) CN1200 D1200 L1203 C1290 R1216 C1230 C1291 L1202 >14P...
  • Page 65: Printed Wiring Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-16. PRINTED WIRING BOARD - MAIN Board (Conductor Side) - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. J1401 J1402 AUDIO AUDIO ZONE 2 OUT VIDEO (VARIABLE FIXED) SAT/CATV SAT/CATV VIDEO 1...
  • Page 66: Schematic Diagram - Main Board (1/4)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-17. SCHEMATIC DIAGRAM - MAIN Board (1/4) - • See page 80 for Waveforms. • See page 81 for IC Block Diagrams. MAIN BOARD (1/4) IC1237 +3.3V REGULATOR IC1237 MM1839A33NRE CONT VOUT R1204 C1202 C1204 C1209...
  • Page 67: Schematic Diagram - Main Board (2/4)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-18. SCHEMATIC DIAGRAM - MAIN Board (2/4) - • See page 81 for IC Block Diagrams. MAIN (Page 68) >104S BOARD (3/4) MAIN BOARD (2/4) >105S MAIN BOARD (4/4) (Page 69) SW– R1312 R1310 C1938 C1937 R1311 R1313 CN1003 SL–...
  • Page 68: Schematic Diagram - Main Board (3/4)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-19. SCHEMATIC DIAGRAM - MAIN Board (3/4) - MAIN BOARD (3/4) >106S MAIN BOARD (4/4) C1545 (Page 69) R1544 CL1865 C1548 D1536 R1559 R1859 R1809 R1659 R1759 R1609 R1709 DZ2J051M0L 100k 100k 100k 100k 100k 100k 100k R1547 6.8k...
  • Page 69: Schematic Diagram - Main Board (4/4)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-20. SCHEMATIC DIAGRAM - MAIN Board (4/4) - MAIN BOARD (4/4) >106S MAIN BOARD (3/4) -58.9 (Page 68) Q1320 Q1321 MSB92T1G 2PD601ART PROTECTOR PROTECTOR R1320 C1320 R1398 1/2W CN1391 CL1364 R1323 C1323 >01S HP_DETECT CL1362 Q1323...
  • Page 70: Printed Wiring Boards - Btw/Coax/Frontjack/Hp Boards

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-21. PRINTED WIRING BOARDS - BTW/COAX/FRONTJACK/HP Boards - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. FRONTJACK BOARD >11P >31P MB-1613 BOARD MB-1613 BOARD (Type-11) (Type-21) CN501 CN501 (Page 74) (Page 60)
  • Page 71: Schematic Diagram - Btw/Coax/Frontjack/Hp Boards

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-22. SCHEMATIC DIAGRAM - BTW/COAX/FRONTJACK/HP Boards - BTW BOARD FRONTJACK BOARD ANT2 ANT3 WIRELESS LAN WIRELESS LAN ANTENNA ANTENNA ANT1 CN1105 PATTERN ANTENNA (FOR BLUETOOTH) CL1173 >04S J2401 MIC_L WIFI1 MB-1613 WLAN/BT BOARD COMBO CARD (2/7) DISPLAY CL1175...
  • Page 72: Printed Wiring Boards - Nfc-Icon/Powerkey/Rs232C Boards

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-23. PRINTED WIRING BOARDS - NFC-ICON/POWERKEY/RS232C Boards - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. (ZA810ES) RS232C BOARD (CONDUCTOR SIDE) CN202 RS232C NFC-ICON BOARD NFC-ICON BOARD RS232C BOARD (SIDE A)
  • Page 73: Schematic Diagram - Nfc-Icon/Powerkey/Rs232C Boards

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES 6-24. SCHEMATIC DIAGRAM - NFC-ICON/POWERKEY/RS232C Boards - • See page 81 for IC Block Diagrams. (ZA810ES) NFC-ICON BOARD RS232C BOARD CN2551 CN2550 CN202 CL2550 R204 VDD3.3V STBY_3.3V CL2551 CL205 FFC3 NFC_SCL FFC4 CL2552 CL204 NFC1 DGND DGND CL2553...
  • Page 74: Printed Wiring Board - Display Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-25. PRINTED WIRING BOARD - DISPLAY Board - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. T1100 >19P >39P MB-1613 BOARD MB-1613 BOARD (Type-11) (Type-21) (Page 72) CN3004 CN3004 (Page 60)
  • Page 75: Schematic Diagram - Display Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 6-26. SCHEMATIC DIAGRAM - DISPLAY Board - • See page 80 for Waveforms. MB-1613 BOARD (6/7) FFC6 DISPLAY BOARD CN1102 CN1103 CL1144 STBY_3.3V CL1143 FFC4 NFC_SCL CL1142 DGND CL1141 >05S NFC_SDA CL1140 NFC_IRQ NFC-ICON CL1139 R1158...
  • Page 76: Printed Wiring Boards - Dcdc Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-27. PRINTED WIRING BOARDS - DCDC Section - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. DCDC BOARD DCDC BOARD (COMPONENT SIDE) (CONDUCTOR SIDE) L1917 D1928 C1050 C1051 L1933 D1927 C1052...
  • Page 77: Schematic Diagram - Dcdc Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 6-28. SCHEMATIC DIAGRAM - DCDC Section - • See page 80 for Waveforms. • See page 81 for IC Block Diagrams. DCDC BOARD D1924 D5SBA60-F F940 CL1961 250V – (Page 79) CN1907 C1029 C1003 C1000 1000...
  • Page 78: Printed Wiring Board - Standby Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 6-29. PRINTED WIRING BOARD - STANDBY Board - • See page 59 for Circuit Boards Location. • : Uses unleaded solder. STANDBY BOARD (CONDUCTOR SIDE) DCDC BOARD (Page 76) >07P CN1905 STANDBY BOARD (COMPONENT SIDE) R974...
  • Page 79: Schematic Diagram - Standby Board

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 6-30. SCHEMATIC DIAGRAM - STANDBY Board - STANDBY BOARD CN940 STBY 10V >07S DCDC STBY GND BOARD AC CUT CN1905 (Page 77) PWR RY T901 F901 MAIN POWER R974 T5AL 250V (DN1080: US, CND, TW/ZA810ES) TRANSFORMER...
  • Page 80 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES • Waveforms – MAIN Board – – DCDC Board – IC1236 qj (X2) IC1916 2 (VBST1) IC1913 2 (VBST1) 304 mVp-p 21.2 Vp-p 17.6 Vp-p 84 ns 1.7 s 100 mV/DIV, 50 ns/DIV 10 V/DIV, 1 s/DIV 10 V/DIV, 2 s/DIV...
  • Page 81 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 • IC Block Diagrams – MAIN Board – IC1232 NJM41050V (TE2) CLAMP VIN1 SREFV ADVANCED 12 VSAG CORRECTION CLAMP 11 SREFV VIN2 10 VCC 9 GND DRIVER 6.75MHz CLAMP LOW-PASS 8 VOUT FILTER – VIN3 MUTE...
  • Page 82 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES IC1414 BD34702KS2 Main Sub1 Sub2 SBLIN INR7 SBRIN INL7 SLIN INR8 SRIN INL8 Mode Mode Mode Mode selector selector selector selector SWIN 7.1 ch OUT +32dB ~ -95dB,-INF/0.5dB step FLIN RECR FRIN RECL Volume Volume Volume Volume Volume...
  • Page 83: Exploded Views

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 SECTION 7 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • The mechanical parts with no reference The components identifi ed by mark 0 they may have some diff erence from the number in the exploded views are not sup- or dotted line with mark 0 are critical for original one.
  • Page 84: Mb-1613 Board Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 7-2. MB-1613 BOARD SECTION not supplied (ZA810ES) supplied with CN202 not supplied (ZA810ES) FFC5 (DN1080: AEP, UK, AUS, TW) (See Note 3) not supplied – Rear view – Note 2: The Ref. No. #11 screw has been changed during production for the AEP, UK, AUS models.
  • Page 85: Power Supply Section (Str-Dn1080)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 7-3. POWER SUPPLY SECTION (STR-DN1080) Note 1: Refer to page 86 for the STR-ZA810ES. not supplied not supplied (US, CND) T901 – Rear view – not supplied supplied not supplied (AEP, UK, AUS) supplied F901 (US, CND)
  • Page 86: Power Supply Section (Str-Za810Es)

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 7-4. POWER SUPPLY SECTION (STR-ZA810ES) Note: Refer to page 85 for the STR-DN1080. not supplied supplied T901 – Rear view – not supplied supplied not supplied F901 supplied #1 #1 not supplied (STANDBY board) supplied not supplied...
  • Page 87: Main Board Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 7-5. MAIN BOARD SECTION not supplied (SUPPORT board) heat sink section not supplied (INSULATION board) Note: The Ref. No. #11 screw has been changed during production for the AEP, UK, AUS models. Check the shape of this screw before replacing it.
  • Page 88: Front Panel Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 7-6. FRONT PANEL SECTION supplied with EN1101 FFC6 supplied with EN1100 not supplied front side not supplied (DISPLAY board) not supplied (See Note) (NFC-ICON board) (See Note) FFC4 NFC1 EN1101 supplied supplied FFC3 not supplied EN1100...
  • Page 89: Heat Sink Section

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 7-7. HEAT SINK SECTION not supplied not supplied not supplied front side Mica sheet is included in each transistor. not supplied Q1800 Q1850 Q1851 Q1801 Q1650 Q1651 Q1750 Q1600 Q1751 not supplied Q1551 Q1700 Q1550 rear side...
  • Page 90: Electrical Parts List

    2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES SECTION 8 COAX DCDC ELECTRICAL PARTS LIST DISPLAY Note: • Due to standardization, replacements in • COILS The components identifi ed by mark 9 con- the parts list may be diff erent from the uH: μH tain confi dential information.
  • Page 91 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.1 DISPLAY FRONTJACK GND BRACKET MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < JUMPER RESISTOR > < TRANSISTOR > JR100 1-216-296-11 SHORT CHIP Q1101 6-552-713-01 TRANSISTOR QS5W2TR JR101 1-216-296-11 SHORT CHIP...
  • Page 92 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CN1200 1-770-160-21 PIN, CONNECTOR (PC BOARD) 2P D1870 6-502-961-01 DIODE DA2J10100L (ANTENNA FM) D1871 6-502-961-01 DIODE DA2J10100L CN1391 1-843-888-11 PIN, CONNECTOR (PC BOARD) 4P...
  • Page 93 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q1572 6-553-334-01 TRANSISTOR KTA1024-Y 0 R1542 1-216-377-51 METAL OXIDE Q1574 6-553-335-01 TRANSISTOR KTC3206-Y 0 R1543 1-216-377-51 METAL OXIDE 0 R1551 1-249-393-91 CARBON 1/4W Q1575 6-553-335-01...
  • Page 94 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 MAIN MB-1613 NFC-ICON POWERKEY RS232C STANDBY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1822 1-216-829-11 METAL CHIP 4.7K 1/10W A-2184-701-A MB-1613 BOARD, COMPLETE (SV) (DN1080: TW) R1829 1-216-842-11 METAL CHIP 1/10W...
  • Page 95 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 STANDBY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D902 6-503-670-01 DIODE GS1G Q1650 6-702-390-01 TRANSISTOR MN2488-OPY-MK D903 6-503-670-01 DIODE GS1G (Including Mica sheet) D904 6-503-670-01 DIODE GS1G Q1651 6-702-391-01 TRANSISTOR MP1620-OPY-MK...
  • Page 96 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES Ver. 1.3 Ref. No. Part No. Description Remark ACCESSORIES ************ Remote control (RMT-AA320U) (1) Calibration microphone (1) 4-686-524-16 INSTRUCTION, OPERATING (ENGLISH) (DN1080: US, CND, UK, AUS) 4-686-524-24 INSTRUCTION, OPERATING (FRENCH, SPANISH) (DN1080: US, CND, AEP) 4-686-524-34 INSTRUCTION, OPERATING (GERMAN, DUTCH,...
  • Page 97 2020/11/17 21:24:35 (GMT+09:00) STR-DN1080/ZA810ES MEMO SYS SET...
  • Page 98 Deletion of Part for Ref. No. C1071 on the DCDC board Change of Part from CLAMP (L35) (Ref. No. 4) to CLAMP (N) (not supplied) Change of Part No. for POWER-SUPPLY CORD (Ref. No. AC1) (STR-DN1080: AEP, UK) Change of Part No. for POWER TRANSFORMER (Ref. No. T901) Change of Part No.

This manual is also suitable for:

Str-za810es

Table of Contents

Save PDF