Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ubiquiti EdgeRouter 6P
Summary of Contents for Ubiquiti EdgeRouter 6P
- Page 1 6-Port Gigabit PoE Router with 1 SFP Port Model: ER-6P...
-
Page 2: Package Contents
Introduction Thank you for purchasing the Ubiquiti Networks® EdgeRouter . This Quick Start Guide is designed to guide you ™ through installation and also includes warranty terms. Package Contents EdgeRouter ER-6P Wall Mount Ground Wall Mount Anchors (Qty. 2) Screw Screws (Qty. -
Page 3: Installation Requirements
AC ground of the power supply. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit: www.ubnt.com/toughcable WARNING: To reduce the risk of fire or electric shock, do not expose the EdgeRouter to rain or moisture. -
Page 4: Hardware Overview
Hardware Overview Front Panel Ports Console SFP (eth5) RJ45 (eth0-eth4) Interface Description RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9, serial console cable, also known as a rollover cable, to connect the Console port to your computer. (If your computer does not have a DB9 port, then you will also need a DB9 adapter.) Then configure the following settings as... -
Page 5: Front Panel Button
Front Panel Button Reset Button Description There are two methods to reset the EdgeRouter to factory defaults: • Runtime reset (recommended) The EdgeRouter should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the LED for port eth5 starts flashing and then becomes solidly lit. - Page 6 We recommend that you update the EdgeRouter to the latest firmware. State Status Flashing White Bootup in progress. Ready for use, not connected to Ubiquiti® White Network Management System (UNMS ™ Blue Ready for use, connected to UNMS.
- Page 7 RJ45: PoE SFP: Speed/Link/Act RJ45: Speed/Link/Act RJ45 LEDs State Status No PoE Green 24V 2-Pair Passive PoE Output Blue 24V 4-Pair Passive PoE Output No Link Amber Link Established at 10/100 Mbps Speed/ Amber Link Activity at 10/100 Mbps Link/ Flashing Activity Green...
-
Page 8: Hardware Installation
Back Panel Ventilation Holes Power Grounding Point Note: There are additional ventilation holes on the sides of the EdgeRouter. Hardware Installation WARNING: FAILURE TO PROVIDE PROPER VENTILATION MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF CLEARANCE NEXT TO THE VENTILATION HOLES FOR ADEQUATE AIRFLOW. - Page 9 3. Position the EdgeRouter with the Ethernet ports facing down. Place the wall-mount slots of the EdgeRouter over the screw heads on the wall. Then slide the EdgeRouter down to lock it into place. Grounding the EdgeRouter (Recommended) The EdgeRouter is grounded through the Power Adapter; however, you can add optional ESD grounding for enhanced ESD protection.
-
Page 10: Connecting Power
Connecting Power 1. Connect the Power Adapter to the Power port. 2. Connect the Power Cord to the Power Adapter. 3. Connect the other end of the Power Cord to a power outlet. - Page 11 Using SFP Ports To use an SFP port: 1. Remove the protective plug covering the SFP port. 2. Plug a fiber SFP module into the SFP port. 3. Connect a fiber optic cable to the fiber SFP module. Then connect the other end of the cable to another fiber device. For information about compatible fiber SFP modules, visit: ubnt.link/SFP_DAC_Compatibility...
- Page 12 Accessing the EdgeOS Configuration Interface The EdgeOS® configuration interface can be accessed via DHCP or static IP address assignment. By default, eth1 is set up as a DHCP client, while eth0 is assigned a static IP address of 192.168.1.1. To configure the EdgeRouter, proceed to the appropriate section: DHCP or “Static IP Address”.
- Page 13 For more information on PoE configuration, refer to “Configuring PoE Settings”. You can also manage your device using the Ubiquiti Network Management System. UNMS lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at www.unms.com Static IP Address 1.
- Page 14 For more information on PoE configuration, refer to “Configuring PoE Settings”. You can also manage your device using the Ubiquiti® Network Management System. UNMS lets you configure, monitor, upgrade, and back up your devices using a single application. Get started at www.unms.com...
- Page 15 Configuring PoE Settings The PoE setting for ports eth0-eth4 is set to Off by default. WARNING: Before activating PoE, ensure that the connected device supports passive PoE and the supplied voltage. 1. In the Dashboard tab, click Actions > PoE of the Ethernet port you want to configure.
- Page 16 EdgeOS User Guide. The User Guide is available at www.ubnt.com/download/edgemax You can also manage your device using the Ubiquiti Network Management System. UNMS lets you configure, monitor, upgrade, and back up your devices using a single application.
-
Page 17: Specifications
Specifications ER-6P Dimensions 229 x 136.5 x 31.1 mm (9.02 x 5.37 x 1.22") Weight 730 g (1.61 lb) Max. Power Consumption 16W (Excludes PoE Output) Power Method External AC/DC Power Adapter, 60W (24V, 2.5A) (Included) Power Supply External AC/DC Adapter Supported Voltage 16 - 30VDC Range... -
Page 18: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Failure to provide proper ventilation may cause fire hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate airflow. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. -
Page 19: Limited Warranty
Limited Warranty www.ubnt.com/support/warranty/ The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions. Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. -
Page 20: Rohs/Weee Compliance Statement
CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. - Page 21 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 22: Declaration Of Conformity
Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.ubnt.com/compliance Íslenska [Icelandic] Hér, UBIQUITI NETWORKS, því yfir að þetta ER-6P tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: www.ubnt.com/compliance... -
Page 23: Online Resources
2014/35/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.ubnt.com/compliance Latviešu valoda [Latvian] Ar šo, UBIQUITI NETWORKS, deklarē, ka ER-6P ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvās 2014/30/ES, 2014/35/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.ubnt.com/compliance Lietuvių... - Page 24 Networks, the Ubiquiti U logo, the Ubiquiti beam logo, EdgeMAX, EdgeOS, EdgeRouter, TOUGHCable, and UNMS are trademarks or registered trademarks of Ubiquiti Networks, Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.