Page 1 User’s Guide Learn how to use your Fujitsu LifeBook V1010 notebook...
Page 2 Copyright and Trademark Information Fujitsu Computer Systems Corporation has made every effort to ensure the accuracy and completeness of this document; however, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document.
Page 3 © Copyright 2007 Fujitsu Computer Systems Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu.
Page 4 This unit requires an AC adapter to operate. Use only UL Listed I.T.E. Class II Adapters with an output rating of 19 VDC, with a current of 4.22 A (80 W). AC adapter output polarity: When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: •...
Page 5: Recycling Your Battery
* To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at in Canada. www.fujitsu.ca/products/notebooks ** RBRC is an independent third party to which Fujitsu provides funding for battery recycling; RBRC is in no way affiliated with Fujitsu. STATE OR FEDERAL LAWS or call 1-800-822-8837.
Page 6: Table Of Contents
Fujitsu Contact Information ........8...
Page 7 LifeBook Application Panel ........32 Opening the Fujitsu Support Center with the Support Button ..32 Launching Applications with the Support Button .
Page 8 Fujitsu Driver Update Utility ........46...
Page 9 Installing Memory Upgrade Modules......66 Removing a Memory Upgrade Module ......68 Checking the Memory Capacity .
Page 10 Caring for your LifeBook Notebook ......102 Cleaning your LifeBook notebook ....... 104 Storing your LifeBook notebook .
Page 11 Glossary ........... . . 119 Regulatory Information .
Page 12: Preface
Keyboard and on-screen keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL]. Pages with additional information about a specific topic are cross-referenced within the text. For example: (“See Installation Procedure on page 43”.) On screen menu items appear in bold. Example: “Click Fujitsu Menu, and select your choice”.
Page 13: Fujitsu Contact Information
HE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU OOK NOTEBOOK Fujitsu Contact Information Service and Support You can contact Fujitsu Service and Support in the following ways: • Toll free: 1-800-8Fujitsu (1-800-838-5487) • E-mail: 8fujitsu@us.fujitsu.com • Website: http://www.computers.us.fujitsu.com/support...
Page 14 OU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE Limited Warranty Your LifeBook notebook is backed by a Fujitsu International Limited Warranty. Check the service kit that came with your notebook for the Limited Warranty period and terms and conditions.
Page 15: Getting To Know Your Lifebook
Getting to Know Your LifeBook Overview This section describes the components of your Fujitsu LifeBook V1010 notebook. We strongly recommend that you read it before using your notebook – even if you are already familiar with notebook computers. Figure 1. Fujitsu LifeBook V1010 notebook...
Page 16: Locating The Controls And Connectors
Locating the Controls and Connectors Display Panel Latch Button Display Panel Stereo Speaker Support Button Touchpad Pointing Device Power/Suspend/Resume Button Stereo Speaker Status Indicator Panel Keyboard Wireless LAN/Bluetooth On/Off Switch Figure 2. LifeBook notebook with display open 11 - Locating the Controls and Connectors...
Page 17: Top Components
Top Components The following is a brief description of your LifeBook notebook’s top components. Display Panel Latch Button The display panel latch button is used to latch and unlatch the display. See “Opening the Display Panel” on page 37. Display Panel The display panel is a color LCD panel with back lighting for the display of text and graphics.
Page 18 Wireless LAN/Bluetooth On/Off Switch The wireless LAN/Bluetooth on/off switch is used to turn on and off the optional WLAN and Bluetooth devices. Switching the device off when not in use will help to extend battery life. See “Activating the WLAN Device” on page 147. Touchpad Pointing Device The Touchpad pointing device is a mouse-like cursor control with a right button, a left button, and a cursor control pad.
Page 19: Left-Side Panel Components
Optical Drive Release Button Optical Drive Figure 3. LifeBook notebook left-side panel Left-Side Panel Components The following is a brief description of your LifeBook notebook’s left-side components. Optical Drive The optical drive bay contains one of the two following drives. See “Optical Drive” on page 56. •...
Page 20: Right-Side Panel Components
Microphone Jack ExpressCard Slot DC-In Jack Modem Jack ExpressCard Eject Button Headphone Jack USB Ports External Video Jack Figure 4. LifeBook notebook right-side panel Right-Side Panel Components The following is a brief description of your LifeBook notebook’s right-side components. ExpressCard Eject Button The ExpressCard eject button is used for removing an ExpressCard from the slot.
Page 21 MAXIMUM SPEED OF RATE DEPENDS ON THE LINE CONDITIONS ACCORDANCE WITH OR ADDITIONAL INFORMATION ABOUT THE MODEM FUJITSU COMPUTERS External Video Port The external monitor port allows you to connect an external monitor or LCD projector. See “External Video Port” on page 74.
Page 22: Back Panel Components
Air Vents USB 2.0 Port LAN (RJ-45) Jack Figure 5. LifeBook notebook back panel Back Panel Components Following is a brief description of your LifeBook notebook’s back panel components. Air Vents The air vents allow air to circulate through the system to cool down the components. O PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE PERFORMANCE AIR VENTS UNOBSTRUCTED DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED...
Page 23 USB 2.0 Ports The USB 2.0 ports allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12Mbps. See “Universal Serial Bus Ports” on page 72. LAN (RJ-45) Jack The internal LAN (RJ-45) jack is used for an internal 10Base-T/100Base-Tx Ethernet LAN connection.
Page 24: Bottom Components
Air Vents (multiple locations) Figure 6. LifeBook notebook bottom panel Bottom Components The following is a brief description of your LifeBook notebook’s bottom panel components. Air Vents The air vents allow air to circulate through the system to cool down the components. O PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE KEEP ALL AIR VENTS UNOBSTRUCTED CLEANING...
Page 25 Memory Upgrade Compartment Your notebook comes with high speed Double Data Rate 2 Synchronous Dynamic RAM (DDR2 SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your notebook, thus improving overall performance. See “Memory Upgrade Module” on page 66. Under normal circumstances, it should not be necessary to open this compartment.
Page 26: Status Indicator Panel
Status Indicator Panel The Status Indicators display symbols that correspond to specific components of your Fujitsu LifeBook notebook. The LEDs below each symbol tell you how each of those components is operating. • Orange, solid: AC adapter and battery are available and system is charging.
Page 27 • Orange, blinking: AC adapter and battery are available and waiting to charge battery (battery is out of thermal range). • Off: AC adapter is not plugged in. Battery Level Indicator The Battery Level indicators display the charge level of the indicated battery pack, as follows: •...
Page 28: Hard Drive/Optical Drive Access Indicator
Hard Drive/Optical Drive Access Indicator The Hard Drive/Optical Drive Access indicator glows green when your internal hard drive is being accessed. Note that flickering is normal. Power Indicator The Power indicator glows blue when your system is turned on. NumLk Indicator The NumLk indicator states that the integral keyboard is set in ten-key numeric keypad mode.
Page 29: Keyboard
Figure 8. Keyboard Using the Keyboard Your Fujitsu LifeBook notebook has an integral 86-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys.
Page 30 characters and as numeric and mathematical keys. The ability to toggle between the standard character and numerical keys is controlled through the [NumLk] key. • Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents.
Page 31 Function Keys Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used. • The [Fn] key provides extended functions for the notebook and is always used in conjunction with another key.
Page 32: Touchpad Pointing Device
Figure 9. Touchpad pointing device The Touchpad pointing device comes built into your Fujitsu LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor control, a left button and a right button.
Page 33: Clicking
N EXTERNAL MOUSE CAN BE CONNECTED TO THE USED SIMULTANEOUSLY WITH THE EXTERNAL MOUSE CONNECTED THE SPECIFICATIONS IN YOUR Clicking Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immediately release it.
Page 34: Double-Clicking
Double-Clicking Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and immediately release it. You can also perform the double-click operation by tapping lightly on the Touchpad twice.
Page 35: Dragging
Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the Touchpad.
Page 36: Volume Control
Volume Control Your Fujitsu LifeBook notebook has multiple volume controls which interact with each other. NY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL...
Page 37: Lifebook Application Panel
The Support button performs different actions when the system is off or when it is on. When the system is off, pressing the Support button will open the Fujitsu Start Boot Menu which allows you to select either Diagnostic Program (Windows Vista and Windows XP systems) to test your system or Recovery and Utility (Windows Vista only) to perform a number of other functions, including recovery of your system.
Page 38: Launching Applications With The Support Button
Manual tab The Manual tab lets you automatically go to the Fujitsu Support website to download the system User’s Guide. (You must be connected to the Internet in order to use this function). Diagnostic Program tab Windows Vista systems: The Diagnostic Program tab allows you to automatically reboot the system, then open the boot menu, from which you can choose Diagnostic Program or Recovery and Utility (same as pressing the button when the system is shut down).
Page 39 Click [Next], [Finish], [OK]. The button will now launch the new application. If you want to return to launching the Fujitsu Support Center utility with this button, you need only click on Fujitsu Support Center from the dropdown list. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application”...
Page 40: Getting Started With Your Lifebook
Getting Started with Your LifeBook DC Power Jack AC Adapter Figure 17. Connecting the AC Adapter Power Sources Your Fujitsu LifeBook notebook has three possible power sources: a primary Lithium ion battery, an AC adapter or an optional Auto/Airline adapter.
Page 41: Connecting The Power Adapters
The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and charging the batteries. Connecting the AC Adapter Plug the DC output cable into the DC power jack of your LifeBook notebook. Plug the AC adapter into an AC electrical outlet. Connecting the Optional Auto/Airline Adapter Plug the DC output cable into the DC power jack on your notebook.
Page 42: Display Panel
Display Panel Your Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active-matrix technology. Opening the Display Panel Press the Display Panel latch button in. This releases the locking mechanism, allowing you to raise the display.
Page 43: Adjusting Display Panel Brightness
Once you have turned on your LifeBook notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness, by using the keyboard or the power management utility. Using the Keyboard Adjusting the brightness using the keyboard changes the setting only temporarily.
Page 44: Starting Your Lifebook Notebook
Starting Your LifeBook Notebook Power On Power/Suspend/Resume Button The Power/Suspend/Resume button is used to turn on your LifeBook notebook from its off state. Once you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your LifeBook notebook.
Page 45: Boot Sequence
This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your notebook is performing a standard boot sequence including a Power On Self Test (POST).
Page 46: Bios Setup Utility
Turn on or restart your LifeBook notebook. To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.
Page 47: Booting The System
When you turn on your notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing the system will load the operating system, and then the Windows Welcome will begin.
Page 48 First of all, you will need to read and accept the End User License Agreements (EULAs). • F YOU REJECT THE TERMS OF THE LICENSE AGREEMENTS YOU WILL BE ASKED TO REVIEW THE LICENSE AGREEMENTS FOR INFORMATION ON RETURNING • OU CANNOT USE YOUR NOTEBOOK UNTIL YOU HAVE ACCEPTED THE PROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE YOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN...
Page 49: Starting Windows Xp The First Time
Registering Windows XP with Microsoft In order to ensure that you receive the most benefits from the Windows operating system, it should be registered the first time you use it. After you receive the Windows Welcome screen, you will be prompted to enter registration information in the following order.
Page 50: Registering Your Lifebook Notebook With Fujitsu
Registering Your LifeBook notebook with Fujitsu You can register your LifeBook by going to our website at: us.fujitsu.com/computers You will need to be set up with an Internet Service Provider (ISP) to register online. Installing Click Me! ClickMe! EFORE INSTALLING THE...
Page 51: Fujitsu Driver Update Utility
Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. For more information about the FDU utility, refer to “Automatically Downloading Driver Updates” on page 83.
Page 52: Power Management
Power Management Your Fujitsu LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating conditions, such as those for the display brightness.
Page 53: Standby (Sleep) Mode
Standby (Sleep) mode in Windows saves the contents of your system memory during periods of inactivity by maintaining power to critical parts. This mode turns off the CPU, display, hard drive, and all other internal components except those necessary to maintain system memory and for restarting. Your notebook can be put in Standby mode by: •...
Page 54: Hibernation (Save-To-Disk) Feature
The Hibernation feature saves the contents of your notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature. Enable or Disable the Hibernation Feature Windows Vista: The default settings are not enabled. To enable or disable the Hibernation feature follow these steps: From the Start menu, select Control Panel.
Page 55: Powering Off
Click the Start button, and then click Shut Down. Select the Restart option from within the Windows Shut Down dialog box. Click OK to restart your notebook. Your notebook will shut down and then reboot. URNING OFF YOUR NOTEBOOK WITHIN YOU START THE NEXT TIME Powering Off Before turning off the power, check that the hard drive/optical drive access indicator is off.
Page 56: User-Installable Features
Chapter 3 User-Installable Features Lithium ion Battery Your LifeBook notebook has a Lithium ion battery that provides power for operating your notebook when no external power source is available. The battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.
Page 57: Recharging The Batteries
• CTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS MANAGEMENT SETTINGS DRIVE ULTI ORMAT HAVE A SIGNIFICANT IMPACT ON BATTERY LIFE THE BATTERY AGES NEW ONE • NDER FEDERAL THEM IN THE TRASH PROPERLY HECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLING OR DISPOSING OF OLD BATTERIES YOUR SUPPORT REPRESENTATIVE AT Recharging the Batteries...
Page 58 SING HEAVY CURRENT DEVICES SUCH AS THE MODEM OR FREQUENT ACCESSES MAY PREVENT CHARGING COMPLETELY Low Battery State When the battery is running low, a low battery notification message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your notebook will go into Standby mode.
Page 59: Replacing The Battery
With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged. There are two ways to swap batteries, cold-swapping and hot-swapping: Cold-swapping Batteries To cold-swap batteries in your battery bay follow these easy steps: Have a charged battery ready to install.
Page 60 Battery Pack Battery Bay Release Latches Figure 19. Removing a Battery Follow steps 3 through 6 in “Cold Swapping Batteries”. F THE ITHIUM ION BATTERY CONNECTOR IS NOT FULLY SEATED YOU MAY NOT BE ABLE TO USE YOUR NOTEBOOK OR CHARGE YOUR BATTERY 55 - Lithium ion Battery...
Page 61: Optical Drive
Media Tray Eject Button Emergency Tray Release Media Holder Tray Figure 20. Optical Drive Optical Drive There is a variety of media available to use with your system, depending upon the system configuration you have selected. Multi-Format DVD Writers and DVD/CD-RW Combo drives are collectively known as “optical drives”.
Page 62: Media Player Software
audio DVD/CDs as well as to read and write to CD-R, CD-RW, DVD-R, DVD+R, DVD-RW, DVD+RW, and DVD RAM discs. The dual-layer architecture allows you to record up to 8.5 GB of data on DVD+R discs. Media Player Software Dual-Layer Multi-Format DVD Writer model only: With the Dual-Layer Multi-Format DVD Writer and media player software you can play DVD movies and music CDs on your LifeBook notebook.
Page 63 THAT YOU CAN ONLY CHANGE THE REGION CODE UP TO FOUR TH CHANGE THE LAST CODE ENTERED BECOMES PERMANENT NSERT OTIFICATION OMPUTER OR FROM WITHIN 58 - Optical Drive FUJITSU COMPUTERS FOR THE WHICH IFFERENT REGION ROPERTIES MENU OF THE AND CANNOT BE UNCTION...
Page 64: Removing Media
Figure 21. Loading/Ejecting Media Removing Media Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will come out of the LifeBook notebook a short distance. Gently pull the tray out until the disc can easily be removed from the tray. Carefully remove the media disc from the holder tray.
Page 65: Using The Media Player Software
Emergency Optical Drive Tray Release If for some reason the eject button fails, you can open the media tray with a paper clip or similar tool inserted into the eject hole in the right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole.
Page 66: Using Media Player On Battery Power
Opening the Media Player Control Panel With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the media player control panel and the mouse. Right-click on the movie screen to open a dropdown menu for options.
Page 67 ’ F YOU DON T HAVE AN ADDITIONAL BATTERY HTTP COMPUTERS FUJITSU OOK NOTEBOOK WILL SHUT DOWN IMPROPERLY MOVIES MAY NOT REQUIRE YOU TO SWAP BATTERIES OR ATTACH OWEVER IT IS BEST TO BE PREPARED SINCE ACTUAL BATTERY LIFE WHILE...
Page 68: Using Expresscards
Using ExpressCards Your LifeBook notebook supports ExpressCards on which type of card you install. Some available ExpressCards: • Gigabit Ethernet Local area network (LAN) cards • IEEE1394 cards • S-ATA II cards • IEEE802.11n WLAN cards For further information, refer to the instructions supplied with your card(s). Eject Button Figure 23.
Page 69: Installing Expresscards
There are two different width ExpressCards: 34 mm and 54 mm. The connector inside the slot is located on the left-hand side of the slot. If you insert a 34 mm card, be sure to align it with the left side of the slot when inserting it.
Page 70: Removing Expresscards
that your notebook is off while installing them. To install an ExpressCard, follow these steps: When not in use, you should keep the ExpressCard plug inserted in the slot to prevent system contamination. Make sure there is no ExpressCard or ExprssCard plug currently in the slot. If there is, see Removing ExpressCards.
Page 71: Memory Upgrade Module
Memory Upgrade Module Your Fujitsu LifeBook notebook comes with a minimum of 512 MB of high speed Double Data Rate Synchronous Dynamic RAM (DDR2-667 SDRAM) factory installed (note that certain system configurations run at 533 MHz). To increase your notebook’s memory capacity, you may install an additional memory upgrade module.
Page 72 Align the memory upgrade module with the component side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. Be sure the alignment keys line up with those in the slot. Figure 25. Opening the Memory Compartment Insert the memory upgrade module at a 45°...
Page 73: Removing A Memory Upgrade Module
Removing a Memory Upgrade Module Perform steps 1 through 4 of Installing a Memory Upgrade Module. Pull the clips sideways away from each side of the memory upgrade module at the same time. While holding the clips out, remove the module from the slot by lifting it up and pulling it away from your notebook.
Page 74 There may be a variation between the actual memory size and what is displayed. This is possible if your system is configured with an integrated Intel Graphics Media Accelerator X3100 which dynamically allocates system memory to accelerate graphics performance. F THE TOTAL MEMORY DISPLAYED IS INCORRECT PROPERLY INSTALLED CORRECTLY RECOGNIZED CHECK THAT YOUR MEMORY UPGRADE MODULE IS...
Page 75: Device Ports
Device Ports Your Fujitsu LifeBook notebook and the optional Port Replicator come equipped with multiple ports to which you can connect external devices including: disk drives, keyboards, printers, etc. Modem (RJ-11) Telephone Jack The modem (RJ-11) telephone jack is used for the internal modem. To connect the telephone cable follow these easy steps: Align the connector with the port opening.
Page 76 Select [Start] -> Control Panel. Select Classic View in the left pane. Double-click Phone and Modems. You may initially need to enter your area code in order to open the Phone and Modem Options window. Select the Modems tab, and click the [Properties] button. Select the Modem tab and adjust the volume as necessary.
Page 77: Internal Lan (Rj-45) Jack
The internal LAN (RJ-45) jack is used for a 10Base-T/100Base-Tx Ethernet LAN connection. You may need to configure your notebook to work with your particular network. (Please refer to your network administrator for information on your network configuration.) To connect the LAN cable follow these easy steps: Align the connector with the port opening.
Page 78: Headphone/Line-Out Jack
System rear Figure 30. Connecting a USB Device Headphone/Line-Out Jack The headphone/line-out jack allows you to connect headphones or powered external speakers to your notebook. Your headphones or speakers must be equipped with a 1/8” (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: Align the connector with the port opening.
Page 79: Microphone/Line-In Jack
The microphone/line-in jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8”(3.5 mm) stereo mini-plug in order to fit into the microphone jack of your notebook. In order to connect a microphone follow these easy steps: Align the connector with the port opening.
Page 80: Troubleshooting Your Lifebook
Chapter 4 Troubleshooting Your LifeBook Troubleshooting There may be occasions when you encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices that can be solved by replacing the device. The information in this section helps you isolate and resolve some of these straightforward issues and identify failures that require service.
Page 81 If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support representative: Toll free: 1-800-8Fujitsu (1-800-838-5487) E-mail: 8fujitsu@us.fujitsu.com Web site: http://www.computers.us.fujitsu.com/support. Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution: • Product name •...
Page 82: Specific Problems
Using the Troubleshooting Table When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty. You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions.
Page 83: Audio Problems
Plugging in headphones disables the built-in speakers, remove the headphones. The Audio Driver may be installed or reinstalled by using the Driv- ers and Applications CD that came with your Fujitsu LifeBook. Refer to your application and operating system documentation for help.
Page 84: Hard Drive Problems
Problem Possible Cause LifeBook notebook fails to Incorrect DVD Player or recognize DVD/CD- no DVD Player soft- RW/CD-ROM’s. ware is installed. Wrong drive designator (continued) was used for the disc in the application. DVD/CD-RW/CD-ROM is dirty or defective. The drive access indicator The Windows auto on the Status Indicator insertion function is...
Page 85: Memory Problems
Problem Possible Cause The built-in keyboard does Your application has not seem to work. locked out your key- (continued) board. You have installed an exter- Your external device is nal keyboard or mouse, and not properly installed. it does not seem to work. Your operating system software is not set up with correct software...
Page 86: Usb Device Problems
Problem Possible Cause USB Device Problems You have installed a USB The device is not prop- device. Your LifeBook note- erly installed. book does not recognize The device may have the device, or the device been installed while an does not seem to work application was running, properly.
Page 87: Power Failures
Problem Possible Cause A card inserted in the Your card device and ExpressCard slot does not another device are work or is locking up the assigned the same I/O system. address. (continued) Power Failures You turn on your LifeBook The installed primary notebook and nothing battery is completely seems to happen.
Page 88 Problem Possible Cause You turn on your LifeBook The power adapter (AC notebook and nothing or auto/airline) has no seems to happen. power from the AC out- let, airplane seat jack, (continued) or cigarette lighter. Your LifeBook notebook The power manage- turns off all by itself.
Page 89 Problem Possible Cause Your LifeBook notebook will The batteries are not work on battery alone. improperly installed. (continued) Your installed batteries are faulty. The batteries seem to You are running an discharge too quickly. application that uses a lot of power due to fre- quent hard drive access or optical drive access, or use of a modem,...
Page 90: Shutdown And Startup Problems
Close all applications and try the button again. Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. See “BIOS Setup Utility”...
Page 91: Video Problems
Problem Possible Cause Your system display won’t You have installed the turn on when the system is LifeBook/Security Appli- turned on or has resumed. cation panel. Video Problems The built-in display is blank The notebook is set for when you turn on your Life- an external monitor Book notebook.
Page 92 Problem Possible Cause The display goes blank by The power manage- itself after you have been ment timeouts may be using it. set for very short inter- vals and you failed to notice the display come (continued) on and go off again. Your display won’t turn on The system may be when the system is turned...
Page 93: Miscellaneous Problems
Problem Possible Cause The Display is dark when The Power Manage- on battery power. ment utility default is set on low brightness to conserve power. You have connected an Your BIOS setup is not external monitor and it does set to enable your exter- not display any information.
Page 94: Power On Self Test Messages
The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual.
Page 95 *Incorrect Drive B type – run SETUP Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
Page 96 *Operating system not found Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:.
Page 97 *Shadow RAM Failed at offset: nnnn Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corruption if you continue. Contact your support representative. nnnn Shadow RAM Passed Where nnnn is the amount of shadow RAM in kilobytes successfully tested. *System battery is dead –...
Page 98 *System timer error The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs. Video BIOS shadowed Video BIOS successfully copied to shadow RAM. 93 - Troubleshooting...
Page 99: Emergency Media Player Drive Tray Release
If for some reason the eject button fails, you can open the DVD/CD-ROM tray with a paper clip or similar tool inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole.
Page 100: Restoring Your Pre-Installed Software
ARE NOT ON THE THE THIRD To re-install drivers and/or applications: Boot up the system and insert the DAR CD after Windows has started. A Fujitsu Installer screen is displayed after the CD is inserted. After reading the License Agreement, click [I agree].
Page 101: Restoring The Operating System For Windows Xp Systems
In the list, check off all the components you want to install. If you want to install all components, click [Select All]. Clicking [Select All] will select all of the blue-coded components; you must select grey and green components separately. Once you have selected the components you wish to install, click [Install Selected Subsystems];...
Page 102: Restoring The Operating System For Windows Vista Systems
(rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps: Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear.
Page 103 Determining whether Recovery and Utility is pre-loaded Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key. From the Boot Menu that appears, check whether the <Recovery and Utility> option is present. If it is not present, it means that the utility must be used from the disc.
Page 104 (rather than booting-up from the hard drive or an external floppy disk drive), perform the following steps: Power on your system. When the Fujitsu logo appears on the screen. press the [Enter] key or click on the left mouse or touchpad button; the TrustedCore Menu will appear.
Page 105 Insert the Recovery and Utility disc into the drive tray. With the boot priority set in the procedure above, the system will boot from the Recovery and Utility disc. Reboot your system. After the system reboots, the Recovery and Utility screen appears. On the screen are three tabs: Diagnostics, Recovery, and Utility.
Page 106: Automatically Downloading Driver Updates
Your system has a convenient tool called the Fujitsu Driver Update (FDU) utility. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. The FDU icon should appear in the system tray at the bottom right of your screen (roll the cursor over the icons to find the correct one).
Page 107: Care And Maintenance
Chapter 5 Care and Maintenance Caring for your LifeBook Notebook If you use your Fujitsu LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices. • •...
Page 108 If your notebook will not boot after it has dried out, call your support representative. • Do not use your Fujitsu LifeBook notebook in a wet environment (near a bathtub, swimming pool). • Always use the AC adapter and batteries that are approved for your notebook.
Page 109: Cleaning Your Lifebook Notebook
• Always disconnect the power plug. (Pull the plug, not the cord.) • Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents. • Use a soft cloth to remove dust from the screen. Never use glass cleaners. •...
Page 110: Storing Your Lifebook Notebook
In addition, a faulty battery might damage your LifeBook. • Store your Fujitsu LifeBook in a cool, dry location. Temperatures should remain between 13ºF (-25ºC) and 140ºF (60ºC). Traveling with your LifeBook notebook •...
Page 111 personnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid problems, place your notebook close to the entrance of the machine and remove it as soon as possible or have your notebook hand-inspected by security personnel. Security officials may require you to turn your notebook on, so make sure you have a charged battery on hand.
Page 112: Batteries
Caring for your Batteries • Always handle batteries carefully. • Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects.
Page 113: Media Care
Caring for your Media (DVD/CD/CD-R) Media discs are precision devices and will function reliably if given reasonable care. • Always store your media disc in its case when it is not in use. • Always handle discs by the edges and avoid touching the surface. •...
Page 114: Expresscards
• Avoid using or storing the drive where it will be subjected to shock or vibration. • Do not disassemble or dismantle the optical drive. • Use of a commercially available lens cleaner is recommended for regular maintenance of your drive.
Page 115: System Specifications
Chapter 6 System Specifications Specifications This section provides the hardware and environmental specifications for your Fujitsu LifeBook notebook. Specifications of particular configurations will vary. Configuration Label The configuration label located on the bottom of your notebook contains specific information regarding the options you’ve chosen for your notebook.
Page 116: Microprocessor
Intel® Core™ 2 Duo or Intel Pentium Dual Core processors (Refer to the system label to determine the speed of your processor). Chipset • Intel 945GM • I/O Controller Hub 7 Mobile (ICH7-M) Memory System Memory • DDR2-667 MHz SDRAM dual-channel memory module. (Note that certain configurations run at 533 MHz).
Page 117: Audio
Video RAM • Intel® Graphics Media Accelerator 950 video graphics. Up to 224 MB shared video memory using Dynamic Video Memory Technology (DVMT) Audio • Realtek codec ALC268 with 2-channel High Definition (HD) audio. • Headphones: Stereo headphone/line-out jack, 3.5 mm, 1 V Ohms •...
Page 118: Features
Integrated Pointing Device • Touchpad pointing device Communications • Modem: Internal V.90 standard 56K fax/modem (ITU V.90, 56K data, 14.4K fax) • LAN: Internal wired 10/100 Ethernet LAN Wireless LAN: • Integrated Atheros SuperAG Wireless LAN (802.11a+b/g) Theft Prevention Lock Lock slot for use with security restraint systems.
Page 119: Keyboard
Built-in keyboard with all functions of 101 key PS/2 compatible keyboards. • Total number of keys: 86 • Function keys: [F1] through [F12] • Feature extension key: Fn • Two Windows keys: one Start key, one Application key • Key pitch: 19 mm •...
Page 120: Dimensions And Weight
Operating: 20% to 85%, relative, non-condensing Non-operating; 8% to 85%, relative, non-condensing Popular Accessories For ordering or additional information on Fujitsu accessories please visit our Web site at www.shopfujitsu.com or call 1-800-FUJITSU. Pre-Installed Software Depending on your pre-installed operating system, your notebook comes with pre-installed software for playing audio and video files of various formats.
Page 121: Learning About Your Software
• CyberLink PowerDVD • Google Desktop • Google Tool Bar • Google Picasa • Fujitsu Driver Update utility • Slingbox Demo • Microsoft Office Small Business Edition 2007 (60-day free trial) • Microsoft Works 8.5 • Evernote Learning About Your Software Tutorials All operating systems and most application software have tutorials built into them upon installation.
Page 122 Internet experience easier and more pleasant. Fujitsu Driver Update Utility The Fujitsu Driver Update (FDU) utility is pre-installed on your system. With FDU, you can choose to automatically or manually go to the Fujitsu site to check for new updates for your system. See “Automatically Downloading Driver Updates”...
Page 123 EverNote EverNote allows you to easily capture, store and access a variety of documents, such as typed and handwritten memos, webpage excerpts, emails, phone messages, addresses, passwords, sketches, and documents. Operating System Options Depending upon your system, one of the following operating system configurations will be installed: Microsoft Windows XP Professional Edition With Microsoft Works 8.5 and Microsoft Office 60-day trial (Small Business Edition 2007) Microsoft Windows Vista Business Edition...
Page 124: Glossary
Glossary AC Adapter A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook. Access point Wireless network device used to bridge wireless and wired network traffic. ACPI Advanced Configuration and Power Interface Active-Matrix Display A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
Page 125 ADSL Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary phone lines. Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as video cards and 3D accelerators. Auto/Airline Adapter A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook notebook.
Page 126 An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook. Byte 8 bits of parallel binary information. Cache Memory A block of memory built into the micro-processor which is much faster to access than your system RAM and used in specially structured ways to make your overall data handling time faster.
Page 127 COM Port Abbreviation for communication port. This is your serial interface connection. Command An instruction which you give your operating system. Example: run a particular application or format a floppy disk. Configuration The combination of hardware and software that makes up your system and how it is allocated for use. Cathode Ray Tube.
Page 128 DIMM Dual-in-line memory module. Disk A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.
Page 129 Disk Operating System (MS-DOS is a Microsoft Disk Operating System). Driver A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.
Page 130 Floppy Disk A spinning platter of magnetic data storage media which is highly flexible. Gigabyte. One billion bytes. Hard drive A spinning platter of magnetic data storage media where the platter is very stiff. Input/Output. Data entering and leaving your notebook in electronic form. I/O Port The connector and associated control circuits for data entering and leaving your notebook in electronic form.
Page 131 IEEE802.11g Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the 2.4 GHz ISM band. Infrared Light just beyond the red portion of the visible light spectrum which is invisible to humans. Infrastructure A name of a wireless LAN configuration.
Page 132 An abbreviation for infrared. IrDA Infrared Data Association. An organization which produces standards for communication using infrared as the carrier. Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed. Kilobyte.
Page 133 MAC Address Media Access Control Address. A unique physical address of a network card. For Ethernet, the first three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique physical address in the world, being assigned with a different address from other cards.
Page 134 Maximum Transmission Unit The maximum data size that can be transferred at a time through the Internet or other networks. You can set a smaller MTU size to obtain successful communication, if you have difficulty transferring data due to the fact that the maximum size is too large. Network key Data that is used for encrypting data in data communication.
Page 135 Partition A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly. PCMCIA PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.
Page 136 Program An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it. Protocol Procedures and rules use to send and receive data between computers. - Method of sending and receiving data - Process used to handle communication errors Conditions required for communication are organized in procedures for correct transfer of information.
Page 137 Read Only Memory. A form of memory in which information is stored by physically altering the material. Data stored in this way can not be changed by your notebook and does not require power to maintain it. SDRAM Synchronous Dynamic Random Access Memory. Serial Port A connection to another device through which data is transferred one bit at a time on a single wire with any other wires only for control of the device not for transfer of data.
Page 138 Status Indicator A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard. Stereo (audio) A system using two channels to process sound from two different sources. Subnet mask TCP-IP network is controlled by being divided into multiple smaller networks (subnets).
Page 139 Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually. Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of devices.
Page 140: Regulatory Information
Regulatory Information Notice Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment. FCC NOTICES Notice to Users of Radios and Television This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to parts 15 of the FCC Rules.
Page 141 If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu Computer Systems Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Page 142 The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information). If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equipment.
Page 143 Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecommunication company cause to request the user to disconnect the equipment from the telephone line.
Page 144 Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur déconnecte l’équipement de la ligne téléphonique.
Page 145: Appendix: Wlan User's Guide
Appendix A: WLAN User’s Guide FCC Regulatory Information Please note the following regulatory information related to the optional wireless LAN device. Regulatory Notes and Statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of these emissions, however, are far much less than the electromagnetic energy emissions from wireless devices such as mobile phones.
Page 146 Regulatory Information/Disclaimers Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
Page 147 003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. Modifications not expressly authorized by Fujitsu Computer Systems Corporation may invalidate the user's right to operate this equipment.
Page 148: Before Using The Wireless Lan
Before Using the Wireless LAN This manual describes the procedures required to properly setup and configure the optional integrated Wireless LAN Mini-PCI device (referred to as "WLAN device" in the rest of the manual). Before using the WLAN device, read this manual carefully to ensure it's correct operation. Wireless LAN Devices Covered by this Document This document is applicable to systems containing an Atheros SuperAG Wireless LAN (802.11a+b/g).
Page 149: Wireless Lan Modes Using This Device
Wireless LAN Modes Using this Device Ad Hoc Mode "Ad Hoc Mode" refers to a wireless network architecture where wireless network connectivity between multiple computers is established without a central wireless network device, typically known as Access Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad Hoc networks are also known as peer-to-peer networks.
Page 150 Access Point (Infrastructure) Mode Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless or wired network devices by communicating through an Access Point. In infrastructure mode, wireless devices can communicate with each other or with a wired network. Corporate wireless networks operate in infrastructure mode because they require access to the wired LAN in order to access computers, devices, and services such as file servers, printers, and databases.
Page 151: Wireless Network Considerations
How to Handle This Device The WLAN device comes pre-installed in your mobile computer. Under normal circumstances, it should not be necessary for you to remove or re-install it. The operating system that your mobile computer comes with has been pre-configured to support the WLAN device. Wireless Network Considerations •...
Page 152: Deactivation Using The Wireless On/Off Switch
Deactivation using the Wireless On/Off Switch The WLAN device can be deactivated quickly and efficiently by toggling the Wireless On/Off Switch to the Off position. The wireless On/Off switch has no effect on non-Wireless LAN models. Disconnection Using the Icon in the Taskbar Note that disconnecting via the icon in the system tray does not turn off the radio;...
Page 153: Configuration Of The Wlan Device
Configuration of the WLAN Device The optional WLAN device can be configured to establish wireless network connectivity using the software that is built into Windows Vista. Support for most industry standard security solutions is contained in this software. Pre-defined parameters will be required for this procedure. Please consult with your network administrator for these parameters: Configuring the WLAN Using Windows Vista Click the Start button, then select Control Panel.
Page 154: Configuring The Wlan Using Windows Xp
Procedure Click the Start button, then select Control Panel. If the Control Panel is not in Classic View, select Classic View from the left panel. Double-click the Network Connections icon. Select “New Connection” wizard. Click the [Next] button. Select “Connect to the Internet”, then click [Next]. Depending upon what type of connection you would like to make, make a selection.
Page 155: Troubleshooting The Wlan
Troubleshooting the WLAN Troubleshooting Table Causes and countermeasures for troubles you may encounter while using your wireless LAN are described in the following table. Problem Unavailable network connection Possible Cause Possible Solution Incorrect network name Ad hoc connection: verify that the network names (SSID’s) (SSID) or network key and network keys (WEP) of all computers to be connected have been configured correctly.
Page 156 Problem Possible Cause Unavailable The WLAN device has network been deactivated or connection disabled (continued) The computer to be connected is turned off RF interference from Access Points or other wireless networks Wireless network authentication has failed Incorrectly configured network settings Incorrect IP address configuration 151 - Troubleshooting the WLAN...
Page 157: Wlan Specifications
WLAN Specifications Item Type of network Transfer rate Active frequency Number of channels Typical operating distances** Security Maximum recommended number of computers to be connected over wireless LAN (during ad hoc connection) 152 - Troubleshooting the WLAN Specification Atheros Super AG (802.11a+b/g) WLAN device conforms to IEEE 802.11a and 802.11b/g (Wi-Fi based)* •...
Page 158 “Wi-Fi based” indicates that the interconnectivity test of the organization which guarantees the interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed. The communication ranges shown above will increase or decrease depending on factors such as number of walls, reflective material, or interference from external RF sources. Encryption with network key (WEP) is performed using the above number of bits, however, users can set 40 bits/104 bits after subtracting the fixed length of 24 bits.
Page 159: Index
Index About This Guide adapter plug adapters Air Vents Anti-theft lock slot Auto/Airline Adapter Automatically Downloading Driver Updates Battery alarm care Charge/DC-In Indicator cold-swapping conserving power dead faulty hot-swapping increasing life Level Indicator lithium ion battery problems recharging replacing shorted Standby mode BIOS guide...
Page 160 EverNote ExpressCard Eject Button problems Slot ExpressCards installing using External Video Port Fujitsu Contact Information Fujitsu Driver Update utility Fujitsu LifeBook traveling Fujitsu Support Center Function Key Hard Disk Drive access indicator problems Headphone Jack Headphone/Line Out Jack Hibernation Feature...
Page 161 Line-Out Jack Lithium ion Battery Media Player battery power care Control Panel loading removing Software using Memory capacity compartment installing problems removing upgrade module Microphone Jack Microsoft Office 2007 Small Business Edition Microsoft Windows Vista Business Edition Microsoft Windows XP Professional Edition Microsoft Works Modem problems...
Page 162 Save-to-Disk ScrLk SDRAM Sleep Mode Specifications Audio Chipset Dimensions and Weight Environmental Requirements Keyboard Mass Storage Device Options Memory Microprocessor Power Video Standby Mode Status Indicator Panel Stereo Speakers Support Button Touchpad buttons controls Touchpad Pointing Device Troubleshooting TrustedCore Menu Universal Serial Bus Ports problems USB 2.0 Ports...

Fujitsu Lifebook V1010 User Manual

Table of Contents

Chapter 1 Getting to Know Your Lifebook

Chapter 2 Getting Started with Your Lifebook

Chapter 3 User-Installable Features

Chapter 4 Troubleshooting Your Lifebook

Specific Problems

Chapter 5 Care and Maintenance

Chapter 6 System Specifications

Appendix: WLAN User's Guide

Quick Links

Chapters

Troubleshooting

Related Manuals for Fujitsu Lifebook V1010

Summary of Contents for Fujitsu Lifebook V1010

Table of Contents