Table of Contents
Advertisement
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
Getting Started
Getting Started
Precautions
Installation
• Prevent internal heat build-up by allowing adequate air
circulation. Do not place the monitor on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
• Do not install the monitor near heat sources such as
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration or shock.
• Do not place the monitor near equipment which generates
magnetism, such as a transformer or high voltage power
lines.
Maintenance
• Clean the cabinet, panel and controls with a soft cloth
lightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent,
such as alcohol or benzine.
• Do not rub, touch, or tap the surface of the screen with
sharp or abrasive items such as a ballpoint pen or
screwdriver. This type of contact may result in a scratched
picture tube.
• Clean the screen with a soft cloth. If you use a glass
cleaning liquid, do not use any type of cleaner containing
an anti-static solution or similar additive as this may
scratch the screen's coating.
Transportation
When you transport this monitor for repair or shipment, use
the original carton and packing materials.
Use of the Tilt-Swivel
With the tilt-swivel, this monitor can be adjusted to the
desired angle within 180° horizontally and 20° vertically.
To turn the monitor vertically and horizontally, hold it at
the bottom with both hands as illustrated below.
15°
90°
5°
4
Get user manuals:
See SafeManuals.com
Warning on power connection
• Use an appropriate power cord for your local power
supply.
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will
not conform to mandatory FCC standards.
Examples of plug types
for 100 to 120 V AC
for 200 to 240 V AC
• Before disconnecting the power cord, wait at least 30
seconds after turning off the power to allow the static
electricity on the CRT display surface to discharge.
• After the power has been turned on, the CRT is
demagnetized (degaussed) for about 3 seconds. This
generates a strong magnetic field around the metal frame,
which may affect the data stored on magnetic tapes and
disks near the bezel. Place magnetic recording equipment,
tapes and disks away from this monitor.
The outlet should be installed near the equipment
and be easily accessible.
90°
SECTION 1
GENERAL
Identifying Parts and Controls
See the pages in parentheses for further details.
Front
1 RESET (reset) button (page 17)
Resets the adjustments to the factory settings.
2 ASC (auto sizing and centering) button
(page 7)
Automatically adjusts the size and centering of the
images.
3 INPUT (input) button and HD15/BNC
indicators (page 8)
Selects the HD15 or 5BNC video input signal. Each time
you press this button, the input signal and
corresponding indicator alternate.
4 MENU (menu) button (pages 8 -17, 19)
Displays the MENU OSD.
5 > (contrast) (?//) buttons (pages 8 – 17,
22)
Adjust the contrast.
Function as the (?//) buttons when adjusting other
items.
6 ¨ (brightness) (./>) buttons (pages 8 –
17)
Adjust the picture brightness.
Function as the (./>) buttons when adjusting other
items.
7 u (power) switch and indicator (pages 19,
22)
Turns the monitor on or off.
The indicator lights up in green when the monitor is
turned on, and either flashes in green and orange or
lights up in orange when the monitor is in power
saving mode.
Getting Started
Getting Started
Rear
8 AC IN connector
Provides AC power to the monitor.
9 Video input 1 connector (HD15)
EN
Inputs RGB video signals (0.700 Vp-p, positive) and
SYNC signals.
F
5 4 3 2 1
10
9
8
7
6
ES
15
14
13
12
11
C
Pin No.
Signal
Pin No.
Signal
1
Red
8
Blue Ground
2
Green
9
DDC + 5V*
(Composite
10
Ground
Sync on Green)
11
ID (Ground)
3
Blue
12
Bi-Directional
4
ID (Ground)
Data (SDA)*
5
DDC Ground*
13
H. Sync
6
Red Ground
14
V. Sync
15
Data Clock(SCL)*
7
Green Ground
* Display Data Channel (DDC) Standard of VESA
!º Video input 2 connector (5 BNC)
Inputs RGB video signals (0.700 Vp-p, positive) and
SYNC signals.
5
Advertisement
Table of Contents
