Related Manuals for Taiga Concept LOHKO FLEX 10
Summary of Contents for Taiga Concept LOHKO FLEX 10
- Page 1 Versio 11/2022 ASSEMBLY GUIDE LOHKO FLEX 10 / FLEX 12 / FLEX 14 TAIGA Product Assembly Guides & Videos www.taigaconcept.fi/assembly...
-
Page 2: Installation
Concept or Taiga Concept local dealers. will break easily. It is recommended to use Taiga Concept local When assembling the product make sure you Choosing location dealers authorized assembling person. - Page 3 If you find damage, document with photos according instructions Check if there is any damage Remove top cover and check that Carry the elements Assemble the product Activate product warranty to the package or pallet there are no signs of damage before www.taigaconcept.fi/activate Note: Take extra care unpacking.
- Page 4 1. Take images where you can see 2. Take closer images of the damage 3. Contact your local Taiga dealer full package from 2 different angles which show the damage 1. Take images where you can see 3. Contact your local Taiga dealer 2.
- Page 5 Lohko Flex 10 Lohko Flex 12 Lohko Flex 14 page 5 of 58 pages...
-
Page 6: Elements & Components
Elements & Components Roof Connector 8x 10x 12x Mini x 15 42x 50x 54x Door metal plinth A 1030 mm 1x 1x T00368 T00184 T00169 5x 5x Hole Cover T00398 4x 4x 26x 30x 30x 1x 1x Window seal 2300 mm T00195 S200 mini x bolt T00185... - Page 7 Elements & Components 100cm Glass A 693 mm width 5x 5x Roof C 1x 2x Plinth C 900 mm 2x 2x Power cable to slave unit 2x 2x T00149 T00179 T00373 EC224 100cm 3x 3x 2x 2x 2x 2x 2x 2x Glass C 788 mm width T00148 Roof B...
- Page 8 Equipments & tools Gloves Safety glasses Safety shoes Safety helmet Screw machine + bits Hex key set Spirit leveler Glass suction cup Step ladder Rubber hammer min weight capacity 50 kg / pcs Carpet knife or Cleaning tools Protection material Scissors for elements and glasses Small adjustable...
- Page 9 ATTENTION Never put glass against hard surface, use always carton or carpet under the glass. Use always 2 person and suction cups to lift glass page 9 of 58 pages...
- Page 10 T00190 Attach 3 mm thick foam under the metal plinth before installing the plinth together First add sides together and add foam under plinths page 10 of 58 pages...
- Page 11 T00190 T00385 Flex 10 = W 3570 mm & D 2970 mm, Flex 12 = W 3570 mm & D 3570 mm, Flex 14 = W 3570 mm & D 4170 mm Connect sides together page 11 of 58 pages...
- Page 12 T00184 T00185 Check that cross measurements match then adding oor plinth in right order page 12 of 58 pages...
- Page 13 T00194 Use long spirit leveler or laser to level the plinth page 13 of 58 pages...
- Page 14 T00195 Add seal 2/3 of the length T00146 When product comes close to wall clean glass before assembling page 14 of 58 pages...
- Page 15 T00195 T00146 page 15 of 58 pages...
- Page 16 T00186 Add before sliding elements together T00146 Adjust the elements to be in same level Adjust level of plinth if there is gap between wall and plinth page 16 of 58 pages...
- Page 17 T00015 T00181 page 17 of 58 pages...
- Page 18 T00399 >2400 mm page 18 of 58 pages...
- Page 19 T00176 page 19 of 58 pages...
- Page 20 T00147 Support the roof and assemble roof joint page 20 of 58 pages...
- Page 21 T00187 page 21 of 58 pages...
- Page 22 T00125 page 22 of 58 pages...
- Page 23 T00124 page 23 of 58 pages...
- Page 24 T00186 T00194 page 24 of 58 pages...
- Page 25 Socket can locate only same line as electric unit page 25 of 58 pages...
- Page 26 T00186 T00194 page 26 of 58 pages...
- Page 27 T00186 page 27 of 58 pages...
- Page 28 T00368 T00181 page 28 of 58 pages...
- Page 29 T00147 page 29 of 58 pages...
- Page 30 T00187 page 30 of 58 pages...
- Page 31 Install 2x cable page 31 of 58 pages...
- Page 32 EC225 EC224 EC224 EC225 EC225 EC224 page 32 of 58 pages...
- Page 33 T00181 page 33 of 58 pages...
- Page 34 T00187 page 34 of 58 pages...
- Page 35 Install 2x cable page 35 of 58 pages...
- Page 36 T00198 Install the seals (T00198) to the edges of the glass to make the joint soundproof and protect the glass. page 36 of 58 pages...
- Page 37 page 37 of 58 pages...
- Page 38 T00198 page 38 of 58 pages...
- Page 39 page 39 of 58 pages...
- Page 40 page 40 of 58 pages...
- Page 41 page 41 of 58 pages...
- Page 42 T00181 page 42 of 58 pages...
- Page 43 T00187 page 43 of 58 pages...
- Page 44 Install 2x cable page 44 of 58 pages...
- Page 45 T00181 page 45 of 58 pages...
- Page 46 Install 2x cable T00187 page 46 of 58 pages...
- Page 47 EC224 EC225 page 47 of 58 pages...
- Page 48 EP109 this side pointing up Assemble CO2 sensor page 48 of 58 pages...
- Page 49 Install Plinth covers page 49 of 58 pages...
- Page 50 Protect the cable when sliding the glass Protect the door metal before assembling front glasses page 50 of 58 pages...
- Page 51 page 51 of 58 pages...
- Page 52 page 52 of 58 pages...
- Page 53 page 53 of 58 pages...
- Page 54 EP106 page 54 of 58 pages...
- Page 55 page 55 of 58 pages...
- Page 56 page 56 of 58 pages...
- Page 57 ATTACH METAL L-PROFILE TO FILL ATTACH METAL L-PROFILE TO FILL THE GAP WITH TWO SIDE TAPE THE GAP WITH SCREWS page 57 of 58 pages...
- Page 58 Activate product warranty www.taigaconcept.fi/activate...
- Page 59 TAIGA Product Assembly support +358 40 138 4302...