Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAMME
START BUTTON
SELECTOR
The indicator lights up during operation, flashes when a fault occurs, and goes off
KNOB
at the end of the programme.
(See Table of
START BUTTON RESET FUNCTION:
programmes
Press this button for at least 2 seconds; the selected programme and options will
below)
be cancelled. Main failure displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions are given in chapter
"What to do if...".
Table of programmes
P
Programmes
1
Pre-Wash
cold
2
Quickwash
40°C
3
2)
50°C
Eco
4
3)
Antibacterial
5
Intensive
70°C
1)
Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance's automatic calibration system.
2)
Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: "nk_customer@whirlpool.com".
3)
The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Detergent
Loading instructions
Crockery to be washed later.
—
Lightly soiled crockery, with no dried-on
food. * Use of tablets not
X *
recommended.
Normally soiled crockery.
X
Energy-saving programme.
Normally or heavily soiled crockery, with
additional antibacterial wash. Programme
X
interruption (e.g. due to door opening) can
compromise elimination of germs.
Recommended programme for heavily
soiled crockery, especially suitable for
X
pots and pans.
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE INSTALLATION
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Options and display description
SALT INDICATOR
When lit, the salt reservoir
ON/OFF
needs to be refilled.
BUTTON
Consumption
1)
Litres
kWh
Minutes
5.0
0.02
10
13.0
0.70
30
15.0
1.05
165
16.0
1.75
120
17.0
1.65
145
ADG 6550
5019 396 01762
Chart
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 6550
Summary of Contents for Whirlpool ADG 6550
- Page 1 ADG 6550 5019 396 01762 EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”. The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
-
Page 2: First Time Use
First time use How to set detergent type: powder/gel/tablet (if option is available) In order to always ensure the best cleaning 1. Select 3rd programme 2. Press START button 3a. Check your 3b..and set it on your dishwasher 4. Remember to use salt and rinse 5. -
Page 3: Daily Check
Daily check Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!) Visual indicator (depending Add salt Visual indicator Fill the salt on model). Screw on the cap. (never add (depending reservoir with Salt residues around cap detergent!). -
Page 4: How To Load The Racks
How to load the racks How to load UPPER RACK (In some models only) B - Adjustable flaps: In horizontal position for cups/long utensils, (In some models only) in raised position for plates and stemware. A - Multipurpose support: Different positions for long C - Cutlery basket: It can be placed in the upper rack when the utensils, cups and glasses. -
Page 5: Select Programme
Select programme Quick, permanent or alternating Overview of programmes The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be found on the panel (page 1). Choose programme according to the attached table of programmes (page 1). Duration of the programme depends on the external conditions in the apartment, temperature and pressure etc. - Page 6 What to do if... If a fault occurs, before restoring normal appliance operation.contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Detergent type” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - In areas with very hard water, more regeneration salt needs to be added (see page 2 “How to set water - Water too hard.
-
Page 8: Disconnect The Mains Plug
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, switch off the appliance, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...