Page 1
ORDER NO.CHM0604022CE DVD Recorder DMR-ES25P / DMR-ES25PC Vol. 1 Colour (S).......Silver Type SPECIFICATIONS 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.
Page 2
Unauthorized copying and distribution is a violation of law. 1. Safety Precaution 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2.
Page 3
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k , 10 watts resistor, in parallel with a 0.15 capacitors, between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Figure 3.
Page 4
wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
Page 5
2.2. Precaution of Laser Diode 2.3. Service caution based on legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
Page 6
lead free solder.) - To put lead free solder, it should be well molten and mixed with the original lead free solder. - Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC. - Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder.
Page 8
5. Feature 5.1. HDAVI Control (HDMI Link) Linked operations by HDAVI Control (HDMI Link) 5.1.1. What is HDMI HDMI is abbreviation of [High-Definition Multimedia Interface], and is digital interface standard for next generation TV corresponding to follows.
Page 9
1. Non-compressing high quality digital image 2. Digital transmission of multi channel digital audio. 3. Two way communication of control signal of control straightening between equipments Pin Name...
Page 10
Pin layout of plug of HDMI cable seen from outside. 5.1.2. Link functions with Equipments Corresponding Table Functions (1) Automatic Input switch (2) Link of Power In case setting of [FUNCTIONS] [Setup] [TV Screen] [Functions of HDMI] [Control with HDMI] are on, all above equipments Link functions are effective. 5.1.3.
Page 11
(2) Power Link Power of DIGA is turned off linking to POWER OFF of VIErA. - Power of DIGA is not turned on linking to POWER ON of VIErA. - It is limited in following cases that DIGA links to POWER OFF of VIErA.
Page 12
7. Operation Instructions 7.1. Taking out the Disc from DVD-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button...
Page 13
7.1.1. Forcible Disc Eject 7.1.1.1. When the power can be turned off. 1. Turn off the power and press [STOP] [CH UP] keys on the front panel simultaneously for 5 seconds. 7.1.1.2. When the power can not be turned off. 1.
Page 14
8. Service Mode 8.1. Self-Diagnosis and Special Mode Setting 8.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on FL will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is ON.
Page 15
Error Diagnosis contents Description Monitor Automatic FL Code Display The unit is carrying No display out its recovery process. Hang-up Displayed when communication No display error has occurred between Main microprocessor and Timer microprocessor. Displayed is left [POWER] key is No error information Initial setting for error code in No display...
Page 16
microprocessor fails. Error Diagnosis contents Description Monitor Automatic FL Code Display No REC Recording is [No REC] is displayed when No display impossible recording is impossible due to the defect, dirt or wound of media. SELF Restoration operation Since the power cord fell out No display CHECK during a power failure or...
Page 17
Item FL display Key operation Mode name Description Front Key TEST Mode *All the main unit's parameters Press [STOP], [CH (include tuner) are initialized. and [OPEN/CLOSE] simultaneously seconds when power off. Rating password The audiovisual level setting Open the tray, and password is initialized to “Level [REC] and [PLAY] 8”.
Page 18
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Display following the then When the power Aging Description shown below mode. press [STOP], [POWER] continually. and [OPEN/CLOSE] simultaneously seconds and less seconds. NOTE1: If Unit has not turned Aging mode by...
Page 19
Item FL display Key operation Mode name Description Front Key Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power lock/unlock press [STOP] and The lock setting is effective until [POWER] keys unlocking the tray and not simultaneously released by “Main unit seconds.
Page 20
Item FL display Key operation Mode name Description (Remote controller Release Items Item of Service Mode executing Press [0] [0] or [ is cancelled. service mode. Error Code Last Error Code of U/H/F held by Press [0] [1] in service Display Timer is displayed on FL.
Page 21
Item FL display Key operation Mode name Description (Remote controller Magenta Picture Magenta picture is output with *Initial mode is “Interlace”. Press [1] [2] in service Output Component Output from AV mode. Decoder. *Magenta picture (Saturation rate: 100%) Switch Interlace/ Press [1] [4] in Magenta *It is enable to switch Interlace/ Progressive...
Page 22
Item FL display Key operation Mode name Description (Remote controller Audio Pattern The audio pattern stored in the Initial mode (Audio 48kHz) Press [2] [3] in service Output internal memory is output mode. (Lch: 1kHz/-18dB) (Rch: 400Hz/-18dB) Audio 44.1kHz/48kHz Press [2] [4] in Audio *Audio sound clock switching switching Pattern Output mode.
Page 23
Item FL display Key operation Mode name Description (Remote controller RAM Drive Last RAM Drive error code display. 1. Error Number is Press [4] [2] in service Error displayed for 5 seconds. mode. *For details about the drive error code, refer to the Service Manual When “INFO**** for the specific RAM Drive.
Page 24
Item FL display Key operation Mode name Description (Remote controller Delete the Last Delete the Last Drive Error Press [9] [6] in service Drive Error information stored on the DVD mode. RAM-Drive. Laser power Drive state is judged based on confirmation difference between laser power into RAM Drive in service...
Page 25
DD: Day Item FL display Key operation Mode name Description (Remote controller Display the Display the accumulated unit's Press [6] [4] in service accumlated working time. mode. working time (Indicating unit: Second) Display the Error Display the Error History stored Display reason of error for Press [6] [5] in service History...
Page 26
Item FL display Key operation Mode name Description (Remote controller SD card WRITE Delete Error History information When the WRITE check is Insert a SD card check stored on the unit. card slot, and press in service mode. *Insert SD card power is off.
Page 27
Part Number Description Compatibility RFKZ0365 Extension Cable (MainP.C.B. - Digital P.C.B. / 64 Pin) JZS0484 Eject Pin Same as E50 Series RFKZ03D01K Lead Free Solder (0.3mm/100g Reel) RFKZ06D01K Lead Free Solder (0.6mm/100g Reel) RFKZ10D01 Lead Free Solder (1.0mm/100g Reel)) RFKZ0316 Solder Remover (Lead free 10W temperature Solder/180g) New RFKZ0328 Flux...
Page 28
10.3. Top Case 1. Remove the 2 screws (A) and 3 Screws (B). 2. Slide Top Case rearward and open the both ends at rear side of the Top Case a little and lift the Top Case in the direction of the arrows.
Page 29
Pull with the front panel in the direction of your side. 10.5. SD Card P.C.B. 1. Remove 1 FFC and 2 Screws (A) to remove SD Card P.C.B.. 10.6. RAM/Digital P.C.B. Module 1. Remove 1 FFC and 6 Screws (A). 2.
Page 30
remove Digital P.C.B. 3. Put Digital P.C.B. on RAM Drive and remove RAM/Digital P.C.B. Module. Note: RAM/Digital P.C.B. Module as service part has no heat sink unit. Before returning to customer, heat sink unit should be installed on Digital P.C.B..
Page 31
10.7. DV Jack P.C.B. 1. Remove 1 Screw (A) to remove DV Jack P.C.B. 10.8. Front (L) P.C.B. 1. Remove 1 Screw (A) and connector.
Page 32
2. Front (L) P.C.B. is removed in the direction of the arrow. 10.9. Rear Panel 1. Remove 6 Screws (A) and 2 Screw (B). 2. Unlock 2 Locking Tabs (A) to remove Rear Panel. 10.10. Main P.C.B. 1. Disconnect Connector for Front (L) P.C.B. 2.
Page 33
10.11. HDMI P.C.B. 1. Pull out the HDMI P.C.B. in the direction of the arrow. 11. Measurements and Adjustments 11.1. Service Positions Note: For description of the disassembling procedure, see the section 10. 11.1.1. Checking and Repairing of RAM / Digital P.C.B. Module...
Page 34
11.1.2. Checking and Repairing of Main P.C.B.
Page 35
11.2. Notice after replacing RAM/Digital P.C.B. Module [TM L1] is displayed after replacing RAM/Digital P.C.B. Module. Once power off, and start up again. 11.3. When the unit does not operate normally after replacing the Timer Microprocessor or Main P.C.B. When the unit does not operate normally after replacing the Timer Microprocessor or Main P.C.B.
Page 36
Turn on the power, and confirm items pointed Items pointed out should reappear. out. Insert RAM disc. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
Item Contents Check Item Contents Block noise Distorted sound Crosscut noise Noise (static, background noise, etc.) Picture Sound Dot noise The sound level is too low. Picture disruption The sound level is too high. Not bright enough The sound level changes. Too bright Flickering color Color fading...
Page 38
Schematic Diagram (FL) 13.11. HDMI Schematic Diagram 13.12. SD Card Schematic Diagram 13.13. DV Jack Schematic Diagram 13.14. Front (L) Schematic Diagram 14. Print Circuit Board 14.1. Main P.C.B. 14.1.1. Main P.C.B. (1/4 Section) 14.1.2. Main P.C.B. (2/4 Section) 14.1.3. Main P.C.B. (3/4 Section) 14.1.4.
Page 39
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMP OUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT...
Page 40
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATA OUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DRPOUT DATA REQUEST DREQ...
Page 41
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 42
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 43
SUB CODE Q DATA SYSCLK SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSS SIGNAL TRON TRACKING ON TRSON...
Page 44
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPT REQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
Page 46
17.2. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 47
of this assembly in production, it will no longer be available. *“(IA)-(IB)”, marks in Remarks indicate languages of instruction manuals. [(IA): English, (IB): Canadian French] *Parts indicated with PAVC-CSG in the Remarks column are supplied by PAVC-CSG. *All parts except parts indicated with (PAVC-CSG) in the Remarks column are supplied by PAVCSG.
Page 67
Front (L) P.C.B. SD Card P.C.B. DMR-ES25P/PC DMR-ES25P/PC SD Card P.C.B. Front (L) P.C.B. (VEP73136A) (VEP70135A)
Page 68
ANA5V LB7412 J0JGC0000020 ANA5V D1R2V D3R8V ANA3R3V X_SW_3R2V C4017 F2A1E470A205 C4018 F2A1E470A205 C4019 F2A1H100A236 R4019 D0HB392ZA002 C4020 F2A1H100A236 R4020 D0HB392ZA002 C D E F G P Q R DMR-ES25P/PC A/V I/O SECTION (3/4) A/V I/O(1/4) Section (Main P.C.B.(2/3)) Schematic Diagram(A)
Page 69
ERJ3GEY0R00V ERJ3GEY0R00V VWJ0795=5 LB4901 K4901 VOUT VOUT J0JHC0000032 VWJ0795=5 ON[H] ON[H] GND NR C4904 C4905 0.1[ZF] F2A1A101A206 AA AB AE AF AG AH AI AJ AK AL AM DMR-ES25P/PC A/V I/O SECTION (4/4) A/V I/O(2/4) Section (Main P.C.B.(2/3)) Schematic Diagram(A)
Page 70
LOCATION MAP P:Power Supply Section:(Page: A:A/V I/O Section:(Page: FL:Timer Section:(Page: DMR-ES25P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE A/V I/O(3/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 71
R3010 LOCATION MAP C7802 0.01 P:Power Supply Section:(Page: DMR-ES25P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. A:A/V I/O Section:(Page: THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE A/V I/O(4/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 72
TPB- TPB+ TPB- NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-ES25P/PC THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DV Jack Schematic Diagram...
Page 73
P7001 EVQ11A04M K1KY04AA0066 KEY3_POWER NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-ES25P/PC THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front(L) Schematic Diagram...
Page 74
1 2 C56140 FL56106 J0JHC0000032 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-ES25P/PC THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. HDMI Schematic Diagram...
Page 79
R656 OUT3 R656 OUT1 R656 OUT2 CLOSE SW R656 OUT0 P.C.B.Name Circuit Name Ref.No. R656 OUT1 Power Supply Ref.No.1100,1200,1300,1500 SERIES Main HDMI P.C.B. R656 OUT0 A/V I/O Ref.No.3000,3900,4000,4900,7400,7800 SERIES P.C.B. SD CARD P.C.B. Timer Ref.No.7500 SERIES DMR-ES25P/PC Interconnection Schematic Diagram...
Page 80
SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. K9ZZ00001279 ANA5V C1505 C1504 ECJ1VB0J105K F1H1A105A028 DMR-ES25P/PC IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. Power Supply Section WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. (Main P.C.B.(1/3))
Page 81
SDAT1 R6805 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-ES25P/PC SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. SD Card Schematic Diagram...
Page 83
SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. HDMI_P_ON_H[5V] HDMI_CONT HDMI_OUT IMPORTANT SAFETY NOTICE: HDD_PFAIL_L COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. VDD3[5V] TIMER SECTION (4/4) DMR-ES25P/PC Timer(2/4) Section (Main P.C.B.(3/3)) Schematic Diagram(FL)
Page 84
2700 R7603 5600 LOCATION MAP P:Power Supply Section:(Page: DMR-ES25P/PC A:A/V I/O Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. Timer(3/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE FL:Timer Section:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 85
FANLOCK CL7508 LOCATION MAP [26]XMPREQ P:Power Supply Section:(Page: DMR-ES25P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. A:A/V I/O Section:(Page: THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE Timer(4/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13.3. A/V I/O (1/4) Section (Main P.C.B.(2/3)) Schematic Diagram (A) LOCATION MAP R7404 I2C_D3R3V ERJ3GEY0R00V NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. I2C_5VCLK I2C_5VDATA Q7402...
13.5. A/V I/O (3/4) Section (Main P.C.B.(2/3)) Schematic Diagram (A) C D E F G A/V I/O SECTION (1/4) LB3914 J0JCC00001 R3926 C3907 LB3913 J0JCC00001 LB3915 J0JCC00001 LB4911 J0JCC0000103 LB4912 J0JCC0000103 LOCATION MAP P:Power Supply Section:(Page: A:A/V I/O Section:(Page: FL:Timer Section:(Page:...
Page 97
J0JCC0000103 J0JCC0000103 LB4903 J0JCC0000103 DMR-ES25P/PC NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE A/V I/O(3/4) Section SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
13.6. A/V I/O (4/4) Section (Main P.C.B.(2/3)) Schematic Diagram (A) AA AB AE AF AG AH AI AJ AK AL AM A/V I/O SECTION (2/4) L3002 G0C220JA0019 C3031 C3032 F2A1E4700048 0.01 C3028 C3001 0.01 CLK MONI DVCC1 C3002 0.033 SLICE DC DVD Y IN R3001 SYNC_CR...
JK3903 K2HA304B0007 K2HA304B0003 LB3907 J0JCC0000103 R3918 LB3908 J0JCC0000103 R3919 LB3909 J0JCC0000103 R3920 L123_SWIDE LOCATION MAP P:Power Supply Section:(Page: DMR-ES25P/PC R ORDERRING. A:A/V I/O Section:(Page: D MAY BE A/V I/O(4/4) Section REPARED. FL:Timer Section:(Page: (Main P.C.B.(2/3)) Schematic Diagram(A)
Page 100
IC3001 IC4001 VIDEO PROCESSOR AUDIO PROC IC-DETAIL BLOCK DIAGRAM IC-DETAIL BL DVD C IN BIAS 6M LPF C75 OUT DVD Y IN CLAMP 6M LPF EXT12 DRV MIX V75 OUT BIAS DVD G/Py IN V75 SAG EXT11 Y75 OUT CLAMP Y75 SAG Py/G SW 6M LPF...
Page 102
13.7. Timer (1/4) Section (Main P.C.B.(3/3)) Schematic Diagram Schematic Diagra LOCATION MAP P:Power Supply Section:(Page: A:A/V I/O Section:(Page: FL:Timer Section:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE. TIMER SECTION (4/4) DMR-ES25P/PC Timer(2/4) Section (Main P.C.B.(3/3)) Schematic Diagram(FL)
Page 107
2700 R7600 2700 R7603 5600 Section:(Page: DMR-ES25P/PC n:(Page: NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. Timer(3/4) Section THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE n:(Page: SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 110
IC7501 TIMER IC-DETAIL BLOCK DIAGRAM CGROM Digit Segmemt Driver Driver CGRAM Address Write Data Code XC IN 13 Code/ Data Command Decoder XC OUT 14 X_RESET REMOCON 25 TBUS CLK P FAL L 29 TBUS RXD Serial Interface P SAVE H TBUS TXD DIP ON H 23 XOUT...
Page 113
J0JHC0000032 LB56110 FL56106 J0JHC0000032 NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-ES25P/PC E CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE GHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. HDMI Schematic Diagram...
Page 117
R6805 SDAT1 NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE DMR-ES25P/PC SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. SD Card Schematic Diagram...
TPB- TPB+ TPB- NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING. DMR-ES25P/PC THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLYDIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. DV Jack Schematic Diagram 13.14.
Page 122
IC56101 Ref No. MODE PLAY STOP IC56102 Ref No. MODE PLAY STOP IC56103 Ref No. MODE PLAY STOP IC56103 Ref No. MODE PLAY STOP IC56103 Ref No. MODE PLAY STOP IC56103 Ref No. MODE PLAY STOP IC56103 Ref No. MODE PLAY STOP IC56103...
Page 123
IC1150 IC1200 IC1302 Ref No. MODE 13.2 -560 PLAY 13.2 -560 STOP 13.2 -560 IC1501 IC1502 IC1503 Ref No. MODE PLAY STOP Ref No. IC1505 MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No.
Page 127
DIGITAL BLOCK SECTION JK3901 A/V OUT JACK P59001 P7401 IECOUT MIX L OUT1 OUT1-L LINE XTMUTE IC7501- Q4002 MIX R OUT1 MUTE OUT1-R Q4001 FROM QR4001,4002,4003 DIGITAL P.C.B. P59001 P7401 XDMUTE MUTE MUTE AUDIO NET SECTION DMR-ES25P/PC Analog Audio Block Diagram...
Page 128
(REAL TIME CLK) (X RESET) XC OUT XRESET 8 XSW+5.2V HDMI P.C.B. P56101 P7502 TO AUDIO XT MUTE XT MUTE HDMI IN BLOCK SECTION P56101 P7502 HDMI-CEC-OUT FROM VIDEO L1 SWIDE L123 SWIDE BLOCK SECTION DMR-ES25P/PC Analog Timer Block Diagram...
Page 129
COUT A CPNCIN DM P7401 P59001 TO DIGITAL Y/V OUT A V YIN DM P7401 P59001 BLOCK SECTION C2 IN CPN 2C IN BIAS Y2 IN CPN 2Y IN CLAMP C/S DET2 C/S DET2 S-VIDEO DMR-ES25P/PC Analog Video Block Diagram...