Advertisement
Available languages
Available languages
Quick Links
The unit is for window mounting only.
Carefully read the installation manual before beginning.
Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may
be exposed:
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install
the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To
prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.
NOTE:
SAVE CARTON and these INSTALLATION
INSTRUCTIONS for future reference. The carton is
the best way to store unit during winter, or when not
in use.
DO NOT USE ANY SCREWS OTHER THAN
THOSE SPECIFIED HERE.
FOR SAFETY REASONS, THE TOP RAIL MUST BE
SECURELY FASTENED WITH ALL FOUR (4)
SCREWS.
Some assembly is required. Please read these instructions
carefully.
Top Rail Hardware
Before installing, the top rail must be assembled on the unit.
A. Remove the air conditioner from the carton and place on a flat surface.
B. Remove top rail from the rear of the packaging material as shown in Fig. A
C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
D. Secure the top rail to the unit with the 3/8" Screws as shown in Fig. C
Packaging
Installation Instructions
READ BEFORE INSTALLING UNIT
WD Window Mounting (8,000-10,000 BTU)
INSTALLATION WARNINGS AND CAUTION
3/8" Screw
Top Rail
Fig. A
Top Rail
Qty.
4
1
Drill (If pilot holes are needed)
Fig. B
Fig. B
Mounting Hardware
( or Wooden windows)
weather stripping
(10"X3/4"X1/12")
window sash seal foam
Fig. C
16120300A31337
Qty.
7
2
2
s)
1
5
1
1
Advertisement
Related Manuals for Frigidaire FHWW085WE1
Summary of Contents for Frigidaire FHWW085WE1
- Page 1 Installation Instructions READ BEFORE INSTALLING UNIT WD Window Mounting (8,000-10,000 BTU) INSTALLATION WARNINGS AND CAUTION The unit is for window mounting only. Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.
- Page 2 Installation How to Install LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table.
-
Page 3: Installation
Installation How to Install Storm Window: FIG. 5 SASH If the air conditoner is blocked by Storm Window, add wood as Board shown in FIG. 5, or remove storm window before air conditioner Storm window thickness as 1-1/2” min is installed. frame or other required, for (38 mm) - Page 4 Installation Drive locking screws: A: For wooden windows: Drive 1/2" (12.7 mm) locking screws through the frame lock and into the sill (FIG. 9A). NOTE:To prevent window sill from splitting, drill 1/8" (3mm) pilot holes before driving screws. Drive 1/2" (12.7 mm) locking screws through frame holes into window sash (FIG.
- Page 5 Installation FIG. 12A & FIG. 12B). normal use, correct the slope otherwise. FIG. 12A FIG. 12B INSIDE OUTSIDE Bottom Rail Bottom Rail about Wooden Window Vinyl-Clad Window FIG. 13 In order to minimize air leaks between the room air conditioner and the window opening, suitable weather stripping(trim the provided weather stripping into suitable size) should be applied in case of any gaps found at the location as indicated by the...
-
Page 7: Instrucciones De Montaje
Instrucciones de montaje LEA ESTO ANTES DE MONTAR LA UNIDAD Montado Ventana WD (8,000-10,000 BTU) IADVERTENCIAS PARA INSTALACION Y PRECAUCIÓN La unidad es para la montaje de ventana solamente. Lea cuidadosamente el manual de instalación antes de comenzar. Siga cada paso como se indica. Observe todos los códigos eléctricos locales, estatales y nacionales y haga la instalación solo con personal calificado, matriculado y autorizado. - Page 8 Instalación How to Install MONTAJE DEL PANEL DE RELLENO IZQUIERDO Y DERECHO NOTA: El raíl superior y los paneles laterales a cada lado se compensan para proporcionar el espacio necesario a la parte trasera de (5/16”). Esto es necesario para el adecuado tratamiento y drenaje del agua condensada. ¡Si no usa los paneles laterales por alguna razón, debe mantener este espacio hasta la parte trasera! Ponga la unidad sobre el suelo, un banco o una mesa de trabajo.
-
Page 9: Instalación
Instalación How to Install Contraventana: HOJA DE LA FIG. 5 VENTANA Grosor del taco tan Marco de Si el aparato de aire acondicionado está bloqueado por un contraventana grande como sea marco de contraventana, añada un taco de madera como 1-1/2”... - Page 10 Instalación Ajuste los tornillos de bloqueo: A: Para ventanas de madera Ajuste los tornillos de bloqueo de 1/2" (12.7 mm) a través de las placas del marco y en el antepecho (FIG. 9A). NOTA: Para evitar que el antepecho se resquebraje, taladre unos agujeros guía de 1/8" (3mm) antes de atornillar.
- Page 11 Instalación Compruebe que el aire acondicionado esté inclinado hacia atrás o debe drenar por el orificio de drenaje durante el uso normal, en cas INTERIOR EXTERIOR Raíl inferior Raíl inferior entre Ventana de madera Ventana de PVC FIG. 13 Para remover el aparato de aire acondicionado de la ventana Remueva el burlete de entre las hojas de la ventana, y remueva la placa de bloqueo de la hoja de la ventana.
-
Page 13: Instructions D'installation
Instructions d’installation LIRE AVANT D’INSTALLER L’UNITÉ Installation pour fenêtre WD (8,000-10,000 BTU) AVERTISSEMENTS D'INSTALLATION ET ATTENTION L'unité est destinée à la fenêtre de montage. Lisez attentivement le manuel d'installation avant de commencer. Suivez chaque étape comme indiqué. Respectez tous les codes électriques locaux, fédéraux et nationaux à l'aide de personnel qualifié, licencié et autorisé uniquement. Prêtez attention aux avis de danger et de sécurité. - Page 14 Installation How to Install ASSEMBLAGE DE BOUCLIERS GAUCHE ET DROIT REMARQUE: le rail supérieur et les panneaux latéraux sur chaque côté sont décalés pour fournir le degré approprié à l’arrière de (5/16”). Ceci est nécessaire pour l’utilisation et le drainage d’eau condensée appropriées. Si vous n’utilisez pas les panneaux latéraux pour une raison quelconque, ce degré...
- Page 15 Installation How to Install Contre-fenêtre : FIG. 5 SASH Cadre de la Épaisseur de Si le climatiseur est bloqué par une contre-fenêtre, ajoutez du panneau selon contre-fenêtre bois comme illustré dans la FIG. 5, ou retirez la contre-fenêtre 1-1/2” min ou autre le besoin, pour avant d’installer le climatiseur.
- Page 16 Installation Enfoncer les vis de blocage : A: pour les fenêtres en bois : Enfoncez les vis de blocage de 12.7 mm (1/2") à travers le verrou de fenêtre et dans le rebord (FIG. 9A). REMARQUE : pour empêcher la division du rebord de fenêtre, percez des trous de départ de 3 mm (1/8" avant d’enfoncez les vis.
- Page 17 Installation Vérifiez que le climatiseur est incliné vers l'arrière d'environ 1/4 à 1/2 pouces (incliné de 2 à 4 degrés vers le bas à l'extérieur, voir FIG. 12A & FIG. 12B). Après une installation adéquate, le condensat ne doit pas s'écouler de l'orifice d'évacuation de trop-plein durant l'utilisation normale, sinon corrigez à...