Table of Contents
Advertisement
Quick Links
Quick reference guide
PROGRAM SELECTION
START/RESUME BUTTON
BUTTON
Push this button to start the selected program: the
Push "Programs" button
indicator lights up and goes off at the end of the
(repeatedly) until the indicator
program. When the door is opened during a
of the required program lights
washing cycle, the cycle is temporarily paused: the
up (see "Table of programs"
Start indicator blinks. To resume the cycle close
below).
the door and push Start button again.
Table of programs
P
Programs
1
Pre-Wash
cold
2
Quickwash 45°C
2)
3
50°C
Eco
4
Intensive
70°C
5
Half Load
50°C
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance's automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
"nk_customer@whirlpool.com".
(see at right for options description)
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter "What to do if ...".
Available
Loading instructions
options
Delay
Crockery to be washed later.
Lightly soiled crockery, with no
Delay
dried-on food.
Normally soiled crockery.
Delay
Power Clean
Energy-saving program.
Recommended program for
Delay
heavily soiled crockery, especially
Power Clean
suitable for pans and saucepans.
Ideal for washing a half load of
Delay
lightly or normally soiled
crockery.
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Options and display description
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
POWER CLEAN
Thanks to the additional
power jets this option
Consumption
provides a more intensive and
Deter-
powerful wash in the lower
gent
1)
Litres kWh Minutes
rack, in the specific area.
This option is recommended
for washing pots and
—
4.0
0.03
14
casseroles (see page 4). Press
this button to activate Power
Clean (the indicator lights up).
X
11.0
0.80
30
X
12.0
1.05
165
TABLET SETTING
X
14.0
1.55
155
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator
lights up) if you are using the combined detergents in
X
10.0
1.04
145
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent,
the Tablet indicator on the control panel has to be off.
ADG 7622
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
Chart
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
DELAYED START
BUTTON
The wash cycle can be
programd to start after
2, 4 or 8 hours. Then
press the Start button.
The wash program will
start after the set time.
5019 396 01941
GB -1-
Advertisement
Table of Contents
Related Manuals for Whirlpool ADG 7622
Summary of Contents for Whirlpool ADG 7622
- Page 1 2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: ADG 7622 5019 396 01941 “nk_customer@whirlpool.com”.
-
Page 2: First Time Use
First time use How to set water hardness in order to always assure the best cleaning results Water hardness should be set only - Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds. before the first wash or if water - Programs LEDs will indicate the water hardness setting. -
Page 3: Daily Use
Daily check Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator Visual The rinse aid dosage can be indicator adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). -
Page 4: How To Load The Racks
How to load the racks How to load UPPER RACK How to adjust upper rack height (if available). (depending on the model) B - Cutlery basket - half: can be placed in the upper rack A - Adjustable flaps: in horizontal position for It could be useful to lift up the upper rack to have when the “Half load/Multizone”... -
Page 5: Maintenance And Care
Select program Overview of programs The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1). Choose program according to the attached table of programs (page 1). Duration of the program depends on the external conditions in the apartment, temperature and pressure etc. - Page 6 What to do if... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance...
- Page 7 What to do if... Crockery and cutlery... Possible causes... Solutions..salt indicator lit - Use tablets for soft water. - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up..have deposits: regeneration salt residue - Water too hard.
-
Page 8: Precautions And General Recommendations
What to do if... Disconnect the mains plug If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty). Before contacting our After-Sales Service, take note of the following: - the description of the fault, - the appliance type and model, - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:...