Table of Contents
Advertisement
Available languages
Available languages
04
_,Mf
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES(800.432.2737) or visit our Website at: GEAppliances.com
In Canada call 1.800.561.3344 or www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
| L J l"_t'_
_'T'A
k |'It
I Ivli_Ui_
| _l_l|
- The dishwasher MUST
be installed
toallow for future removalfromtheenclosure
if service is required.
I M
PORTANT
Observeall governing codes and
ordinances.
• Note to Installer - Be sure to leave these instructions for the
consumer's and local inspector's use.
• Note to Consumer - Keep these instructions with your
Owner's Manual for future reference.
• Skill Level- Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper
installation
is the responsibility of the installer. Product
failure due to improper installation
is not covered under
the GE Appliance Warranty. See warranty
information.
• Completion Time - 1 to 3 Hours. New installations require
more time than replacement installations.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories - See the Owner's Manual for available
custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONSand WARNINGS
shown throughout these instructions, While performing
installations
described in this booklet, gloves and either
safety glasses or goggles should be worn,
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Stainless Steel Tub Models
imagination at work
Advertisement
Table of Contents
Related Manuals for GE PDWT380R10SS
Summary of Contents for GE PDWT380R10SS
- Page 1 _,Mf Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES(800.432.2737) or visit our Website at: GEAppliances.com In Canada call 1.800.561.3344 or www.GEAppliances.ca BEFORE YOU BEGIN | L J l"_t'_ _'T'A k |'It I Ivli_Ui_ | _l_l| - The dishwasher MUST...
-
Page 2: Installation Preparation
Installation Preparation Screw Kit PARTS SUPPLIED WITH Side Trim INSTALLATION KIT: Side Trim [] Two #8-18 x 5/8" Phillips special head screws, to #8 Phillips #10 Hex-Head secure dishwasher to underside of countertop or Top Trim Special Head Screws J-Box Screw sides of cabinets. -
Page 3: Installation
Installation Preparation-Enclosure • The dishwasher must be installed no more than 10 feet PREPARE DISHWASHER ENCLOSURE from sink for proper drainage. The dishwasher must be fullg enclosed on the top, sides To reducethe risk o f shock, fire, or injurg and back. -
Page 4: Prepare Drain Plumbing
Installation Preparation-Drain PREPARE DRAIN PLUMBING METHOD 1-Air Gap with Waste Tee or Disposer Drain Requirements • Drain hose must not exceed 10 feet in length. • A high drain loop or air gap is required. See below. Drain Method The tgpe of drain installation depends on the following: •... -
Page 5: Prepare Electrical Wiring
Installation Preparation-Electrical Supplg PREPARE ELECTRICAL WIRING FOR PERSONAL SAFETY: Remove house fuse Alternate or open circuit breaker before beginning installation. Do not use an extension cord or Receptacle adapter plug with this appliance. Location 1-1/2" Dia. Hole (Max.) PARA SEGURIDAD PERSONAL: Retire el 3"... - Page 6 Installation Preparation-Hot Water Supply PREPARE HOT WATER SUPPLY CAUTION Hot Water Line • The line meg enter from either side, rear or floor within the The hot water supplg line pressure must be at least 20 PSI. shaded area shown in Figure F. Lower pressures could cause the water valve to leak and •...
- Page 7 Dishwasher Installation Tgpe 1 - One-hole cable CAUTION Adjust tension bg moving spring hook to one of the three holes on the tub leg. Do not remove the wood base until you are ready to install the dishwasher. The dishwasher will tip over when the door is opened if the base is removed.
- Page 8 Maximum power cord length is 6 feet. Power Cord base with an adjustable wrench or 15/!6" socket. Kit wxogx70910, available for purchase from an authorized • Discard base. GE Appliance Dealer, meets these requirements. )rox. Ground Figure K . Screw leveling legs back into the dishwasher frame approximatelg !/8"...
-
Page 9: Step 8 - Install 90 ° Elbow
STEP 9 - POSITION WATER LINE AND hose (!0 feet) may HOUSE WIRING be purchased from • Position water supply an authorized line and house wiring GE appliance on the floor of the dealer. The enclosure to avoid !0' long interference with hose is... - Page 10 Dishwasher Installation STEP 11 - INSERT DRAIN HOSE STEP 12 - SLIDE DISHWASHER THREE- THROUGH CABINET FOURTHS OF THE WAY INTO • Position dishwasher in front of cabinet opening. Insert drain CABINET hose into the hole in cabinet side. If a power cord is used, guide the end through a separate hole.
- Page 11 Dishwasher Installation STEP 13 -SLIDE DISHWASHER INTO Special Considerations for Positioning FINAL POSITION Top-Mount Control Models • Push the dishwasher the rest of the wag into the cabinet. • Push the sides with your hands. Do not push the dishwasher The controls on these models are designed to be hidden by with your knee, as this will damage the door.
- Page 12 Dishwasher Installation STEP 14 - LEVEL DISHWASHER STEP 15 - SECURE DISHWASHER COUNTERTOP OR CABINET IM PORTANT- Dishwasher must be level for proper In this step gou will need dish rack operation and wash performance. the 2 Phillips special head Brackets screws set aside in Step 1.
- Page 13 Dishwasher Installation STEP 16 - CONNECT WATER SUPPLY NOTE:TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10' FOR PROPER DRAIN OPERATION. Connect water supply line to the 90 ° elbow. • Slide compression nut, then ferrule over end of water line. DRAIN LINE INSTALLATION •...
-
Page 14: Step 18 - Connect Power Supply
Dishwasher Installation STEP 18 - CONNECT POWER SUPPLY STEP 19 - PRETEST CHECKLIST Skip this step if dishwasher is equipped with power cord, Review this list after installing gour dishwasher to Verify that power is turned off at the source. avoid charges for a service call that is not covered bg gour •... -
Page 15: Step 20 - Dishwasher Wet Test
Dishwasher Installation STEP 20 - DISHWASHER WET TEST STEP 22 - INSTALL SOUND UPGRADE KIT IF EQUIPPED [] Turn on power supply (or plug power cord into outlet, if equipped). Skip this step if gour model does not have the Sound Upgrade Kit. -
Page 16: Dishwasher Installation
STEP 24 - LITERATURE ,, Be sure to leave complete literature package, Installation Instructions and product samples with the consumer. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer & Industrial General Electric Company Louisville, Kentucky/40225 GEAppliances.com 206C!559P!99 31-30260... - Page 17 Instructions d'i kave-vaisselle encastr Si vouz des questions, appelez 800.GE.CARES ou visitez notre site Web" GEAppliances.com Au Canada, appelez le 1.800.561.3344 ou visitez • www.electromenagersge.ca AVANT DE COMMENCER IMPORTANT- Le lave-vaisselle DOlT @treinstall_ de mani@re@permettre la d@ose ult@rieurede I'enceinte afin de II faut lire soigneusement toutes ces instructions.
- Page 18 Preparation pour I'installation PII_CES FOURNIES AVEC LE KIT de vis Ensemble Finition lat_role D'INSTALLATION Finition lat_rale Deux vis sp_ciales _ t_te cruciforme n° 8-18 x 5/8 po, pour fixer le lave-vaisselle au-dessous du plan de travail. Vis sp_ciales 6 t_te Vis pour boTte Finition sup(_rieure Un couvercle de boTtedejonction et une vis d t@te...
- Page 19 Preparation pour I'installation - Enceinte PR#PARATION DE L'ENCEINTE DU • II faut installer le lave-vaisselle 6 moins de 3 m (10 pi) de I'_vier pour que I'_coulement suit ad_quat. LAVE-VAISSELLE Le lave-vaisselle doit _tre enti_rement enclos sur le haut, les c6t_s et I'arri_re.
-
Page 20: Preparation Pour L'installation
Preparation pour l'installation - Vidange PRI_PARATION DE LA PLOMBERIE DE MI_THODE i - Dispositif anti-siphon avec raccord en t_ d'@gout ou de brogeur _ d_chets VIDANGE Exigences de vidange • Le tugau de vidange ne peut pas _tre plus de 3 m (10 pi) de long. - Page 21 Preparation pour l'installation -Alimentation lectrique PRE_PARATION POUR LE BRANCHEMENT I_LECTRIQUE SI_CURITI_ : Autre emplacement- Enlever le fusible du circuit possiblede la prisede courant d_clencher le disjoncteur avant de commencer l'instaIIation. Avec cet appareil, ne pas utiliser une rallonge ou un adaptateur de prise.
- Page 22 Preparation pour l'installation -Alimentation d 'eauchaude PRI_PARATION DE L'ALIMENTATION D'EAU PRUDENCE: CHAUDE La pression de la conduite d'alimentation d'eau chaude Tugau d'eau chaude doit _tre d'au moins 1,4 bar (20 psi). Une pression plus • Le tuyau peut entrer d'un c6t_ ou de I'autre, de I'arri_re ou du faible risque de causer une fuite dans le robinet et des sol, duns la zone hachur_e montr_e 6 la figure F.
-
Page 23: Installation Du Lave-Vaisselle
Installation du lave-vaisselle Tgpe 1- COble 6 un trou PRUDENCE: Ajuster la tension en plaqant le crochet de ressort dons un des trois trous du pied du bac. Ne pas enlever la palette en bois avant d'@tre pr@t6 installer le lave-vaisselle. Le lave-vaisselle bascule Iorsque la porte est ouverte sans la base. - Page 24 Iocaux. La Iongueur maximale du cordon @lectrique Enlever la palette. est de 2 m@tres(6 pi). Le kit de cordon d'alimentation WX09X70910, en vente chez les distributeurs agr@@s d'appareils m_nagers GE,satisfait _ ces crit_res. Environ 3,2 mm (!/8 po) Blanc Figure K •...
- Page 25 I (5po) (5po) 1lOcm d'appareils de I'ouverture, afin _ ! ¢_po) m@nagers d'@vitertoute GE.Le interf@rence avec tugau de la base du lave-vaisselle 3 m (10 pi) et des divers porte le @l_mentssous celui-ci. num@rode piece GPFIOL.
- Page 26 installation du lave-vaisselle ETAPE 11" INSERTION DU TUYAU DE ETAPE :1.2• GLISSER LE LAVE-VAISSELLE #, VIDANGE A TRAVERS L'ARMOIRE TROIS QUARTS DANS L'OUVERTURE DE • Mettre le lave-vaisselle en position devant I'ouverture. Ins@er L'ARMOIRE le tuyau de vidange dans le cBt_ de I'armoire. Si un cordon d'alimentation est utilis_, guider son extr_mit_ dans un trou i L j r_ f% IF_-,I_A...
- Page 27 installation du lave-vaisselle I_TAPE 13" PLACEMENT DU LAVE-VAISSELLE consid_rer Points h pendant le placement de modules h commandes mantles #, SA POSITION FINALE le haut • Pousser le lave-voisselle tout 6 fait dans I'ormoire. • Pousser des mains sur les c6t_s. Ne pas utiliser le genou pour Les commandes de ces modules sont conques pour _tre ne pas endommager Io porte.
- Page 28 installation du lave-vaisselle I_TAPE 14" MISE #, NIVEAU DU I_TAPE 15" FIXATION DU LAVE-VAISSELLE LAVE-VAISSELLE A L'ARMOIRE ]_cette _tape, il faut les IM PORTANT - Lelave-vaisse,e doit_tredeniveau 2 vis sp_ciales _ t_te cruciforme mJses de c6t_ pour obtenir un bon d_placement de l'_gouttoir et du lave- Pattes de __<...
- Page 29 Installation du lave-vaisselle ETAPE 16" BRANCHEMENT REMARQUE : POUR OBTENIR UNE BONNE VIDANGE, LA LONGUEUR TOTALE DU TUYAU DE VIDANGE NE DOlT PAS L'ALIMENTATION D'EAU DEPASSER3 m (!0 pi). Brancher le tugau d'alimentation d'eau au coude 6 angle droit. INSTALLATION DU TUYAU DE VIDANGE •...
- Page 30 installation du lave-vaisselle I TAPE 18" BRANCHEMENT I TAPE 19 : LISTE DE VITRIFICATION AVANT DE FAIRE LES ESSAIS L'ALIMENTATION I LECTRIOUE Sauter cette _tape si le lave-vaisselle est _quip_ d'un cordon Examiner cette liste apr_s l'installation du lave-vaisselle d'alimentation. V_rifier que le circuit est hors tension pour _viter les frais d'intervention qui ne sont pas couverts...
- Page 31 installation du lave-vaisselle I_TAPE 20" ESSAI DU LAVE-VAISSELLE AVEC I_TAPE 22 - INSTALLATION DU KIT DE DE L'EAU RI_DUCTION DE BRUIT, LE CAS I_CHI_ANT iVlettre le circuit sous tension (ou brancher le cordon Sauter cette _tape si le modSle n'est pus _quip_ du kit de d'alimentation dans la prise de courant, si install_e).
- Page 32 I_TAPE 24- DOCUMENTATION • Prendre soin de laisser au consommateur I'enveloppe complete de documentation, les instructions d'installation et les _chantillons de produit. LES DONNEES TECHNIQUES PEUVENT CHANGER SANS PREAVIS GE Consumer & Industrial General Electric Company Louisville, Kentucky 40225 206C!559P!99 31-30260 07-09 GEAppliances.com...