Thermador WD24 Installation Instructions
Warming drawer
Hide thumbs
Also See for WD24:
- Care and use manual (8 pages) ,
- Installation instructions manual (20 pages) ,
- Use and care manual (32 pages)
Advertisement
Quick Links
®
INSTALLATmON
iNSTRUCTIONS
MODEL
WD24/WD27/WD30
WARMING
DRAWER
PLEASE
READ ENTtRE iNSTRUCTiONS
BEFORE
PROCEEDnNG.
iNSTALLATiON
MUST COMPLY WITH ALL LOCAL CODES.
The warming
drawer
is completely
self-contained
and ready
for installation.
Power
Supply:
120Volts,
15 Ampere,
60 Hz.
iMPORTANT:
Before
turning
on power,
be sure that the control
is turned
to "OFF."
FIGURE
1
Frame
1ol/2" Min. to
Cabinet
Allow 3ol/2" in front for
drawer handle clearance
Wal_
Receptacle
Support
Brackets
.
,
Table
1
MODEL
MODEL
MODEL
WD24
WD27
WD30
DIM
A
22-3/4"
25-3/4"
25-3/4"
DIM
B
9"
10"
10"
DIM
C
20-1/4 ''
22°1/4"
DIM
D
3/8"
9/lg'
2-!/8"
TABLE 1: Cut out Dimensions
INSTALLING
THE
WARMING
DRAWER
The opening
ha the wall or cabinet
should
be A wide
x B high
x C deep
minimum
as shown
in Table
1.
Install
two
support
brackets
(provided)
8" from
the front of the wall
or cabinet
at the same level
as
the bottom
of the opening.
(See Fig. 1)
Push unit into opening
until it clears
support
brack-
ets and supports
its own weight.
Push
unit tight
against
wall or cabinet
and secure
with
four screws
(provided).
Two screws
go into
top two corners
of front
frame,
the others
go at the
bottom
of the front
frame.
.
When
sta: king one drawer
above
the other
or side-
by-side
installation,
allow
1-1/2"
between
cutouts.
If you desire
a gap between
the units,
allow
more
space between
the cutouts.
Allow
2-1/2"
between
cutouts
when
installing
the warming
drawer
un-
der a wall oven.
Advertisement
Related Manuals for Thermador WD24
Summary of Contents for Thermador WD24
- Page 1 ® INSTALLATmON iNSTRUCTIONS MODEL WD24/WD27/WD30 WARMING DRAWER PLEASE READ ENTtRE iNSTRUCTiONS BEFORE PROCEEDnNG. iNSTALLATiON MUST COMPLY WITH ALL LOCAL CODES. The warming drawer is completely self-contained and ready for installation. Power Supply: 120Volts, 15 Ampere, 60 Hz. iMPORTANT: Before turning...
- Page 2 ELECTRICAL REQUIREMENTS & GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE CONNECTED FIGURE A RECEPTACLE A CIRCUIT RATED Receptacle Three-Prong VOLTS, 15 AMPERE, 60 Hzo Cover Plate Fteceptacie Always disconnect electric supply cord from wall outlet before servicing this appliance. Observe all governing codes and ordinances when grounding.
- Page 3 PROCEDURE CUSTOM WOOD DOOR FRONT Changes in construction Construction of the Warming from damaging it. The custom Drawer door is such that, wood panel's dimensions are A equipment be made from time to time by the manufacturer glass panel can be replaced with X B overall, Refer...
- Page 4 Thermador reservesthe rightto change specifications or design without notice.Some models are certified f or use inCanada. Thermador isnot responsib[e for products which _re transported from the United Statesfor use inCanada. Check with your local Canadian distributor or dealer. Thermador, SSS I McFadden Avenue, Huntington Beach, CA 92649.