Page 1
PIONEER ELECTRONICS (USA) INC. P.O.Box 1760, Long Beach, CA 90801-1760 U.S.A. PIONEER EUROPE NV Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE.LTD. 253 Alexandra Road, #04-01, Singapore 159936 C PIONEER CORPORATION 2003 K-ZZA. APR. 2003 Printed in Japan...
Page 2
Unplugging and plugging the connectors dur- ing power-on mode may damage the ICs inside the unit. 2. To protect the pickup unit from electrostatic dis- charge during serviving, take an appropriate treat- ment(shorting-solder) by referring to "the DISAS- SEMBLY" on page 79. FX-M2137ZSA/X1B/UC...
2. A “CLASS 1 LASER PRODUCT” label is affixed to the unit frame. bottom of the player. CLASS 1 LASER PRODUCT 4. Specifications of Laser Diode Specifications of laser radiation fields to which human access is possible during service. Wavelength = 800 nanometers FX-M2137ZSA/X1B/UC...
1. SPECIFICATIONS - FX-M2137ZSA/X1B/UC TAPE Power source.............13.5V±0.1V Tape ........Compact cassette tape(C30-C90) Grounding system........Negative type Tape speed ..4.76 cm/sec.(+0.14 cm/sec.,-0.05 cm/sec.) Dimensions ....195.6(W) 118.2(H) 183.5(D)mm Crosstalk ............40dB or less Weight ................2230g Separation .............35dB or more Backup current ..........0.3mA or less S/N ..............45dB or more Distortion.............2% or less...
Page 6
AM TUNER Usable discs ..........Compact disc Frequency ..........531-1602 kHz(9kHz) Signal ........Sampling frequency:44.1kHz 530-1710 kHz(10kHz) Number of quantization bits:16;linear Selectivity .........45dB or more(±9kHz) S/N ..............80dB or more S/N ..............45dB or more Distortion............0.03% or less Distortion............1.0% or less Separation .............70dB or more FX-M2137ZSA/X1B/UC...
Page 10
(2) CONTRAST TABLE FX-M2137ZSA/X1B/UC, FX-M2037ZSA/X1B/EW and FX-M2337ZSA/X1B/ES are constructed the same except for the following: Part No. Mark No. Symbol and Description FX-M2137ZSA/X1B/UC FX-M2037ZSA/X1B/EW FX-M2337ZSA/X1B/ES 11 Connector Not used UDE-040 Not used 15 Insulator Not used UNM-010 Not used 16 Tuner Mother Assy...
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM(FX-M2137ZSA/X1B/UC, FX-M2337ZSA/X1B/ES) TUNER MOTHER PCB TUNER UNIT FM IF FILTER FM IF FM IF OUT CN501 CF51 FM IF FM RF Q471 FM IF FM MIX CF52 CF53 ANTENNA FM ANT AM ANT...
Page 17
IC 651 VOLUME PCB(B) UPD72005GC CN902 stby CN602 ejsw KEYBOARD UNIT X651 8.5V CAN VDD POWER SUPPLY POWER SUPPLY Q802 Q805 CANVDD SYSB Q801 Q804 SWVDD SWVDD Q806 Q809 B.U 5V SW5V REFERENCE Q808 POWER IC 803 SUPPLY S-81250PGPD Q807 FX-M2137ZSA/X1B/UC...
FM IF FILTER Detailed page FM LOOP FILTER DIVERSITY CN701 POWER SUPPLY CD:+0.2dBs PLL IC AM LOOP FILTER ANTENNA ISOLATOR CD CONTROL EJLD RDS CONTROL RDS DECODER TUNER MOTHER PCB FX-M2017ZSA/X1B/EW KEYBOARD UNIT FX-M2117ZSA/X1B/UC FX-M2317ZSA/X1B/ES A D E VOLUME PCB(A) FX-M2137ZSA/X1B/UC...
Page 21
No differentiation is made between chip capacitors and 0.022 R022 discrete capacitors. VOLUME PCB(B) The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of CB(A) identical designation. FX-M2137ZSA/X1B/UC...
3.6 CD MECHANISM MODULE Pickup Unit(Service)(P10) MOTOR DRIVER SPINDLE MOTOR M1 CXB6007 LOADING/CARRIAGE MOTOR M2 CXB8933 3.3V REGULATOR FX-M2137ZSA/X1B/UC...
Page 31
S901 : HOME SWITCH..ON-OFF S902 : CLAMP SWITCH..ON-OFF S903 : DSCSNS SWITCH..ON-OFF RF AMP / SERVO / DSP S904 : 12EJ SWITCH..ON-OFF S905 : 8EJ SWITCH..ON-OFF DAC / LPF The underlined indicates the switch position. UPD63712AGC CD CORE UNIT (S10) CN701 FX-M2137ZSA/X1B/UC...
Page 32
500mV/div 200ms/div 500mV/div 2ms/div 1V/div 500 s/div ! FE # RFAGC 0 TE 500mV/div 500mV/div 500mV/div 7 TIN 500mV/div Focus Search When "Tracking Open" 1 Track Jump Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST FX-M2137ZSA/X1B/UC...
Page 33
200 s/div 5V/div 200ms/div 5V/div 200ms/div % ROUT 2 CLCONT 2 CLCONT 1V/div 5V/div 5V/div 3 LOEJ 3 LOEJ 5V/div 5V/div Analog Audio When "Eject"(12cm CD) When "Eject"(8cm CD) Ref.: Ref.: Ref.: AGND Mode: Mode: Mode: Normal Normal Normal FX-M2137ZSA/X1B/UC...
3.8 SUB TUNER UNIT(FX-M2037ZSA/X1B/EW) SUB TUNER UNIT TUNER MOTHER ASSY Consists of TUNER MOTHER PCB CONNECTOR PCB SUB TUNER UNIT CN551 FX-M2137ZSA/X1B/UC...
1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram. 2.Viewpoint of PCB diagrams Capacitor Connector CN852 SIDE A SIDE B Chip Part P.C.Board CN901 CN701 FX-M2137ZSA/X1B/UC...
Page 39
SIDE A ANTENNA TUNER UNIT CN251 CN902 FRONT FX-M2137ZSA/X1B/UC...
4.9 CASSETTE MECHANISM MODULE SIDE A DECK UNIT CN651 CN251 C321 C273 DECK UNIT SIDE B HEAD ASSY IC,Q VR302 CN254 CN255 CN253 IC351 CN252 IC251 Q351 Q352 VR301 CN256 FX-M2137ZSA/X1B/UC...
Page 53
SENSOR UNIT S101 LOAD S103 70 s S102 MODE CN256 Q101 REEL SENSE CN253 FX-M2137ZSA/X1B/UC...
VR156 VR154 DC V Pin 1 Meter(2) SUB TUNER UNIT(SIDE B) DC V Meter(4) TUNER UNIT(SIDE B) Meter(3) Center Center Meter(2) Meter(1) DC V Meter(5) AOUT DC V DECK UNIT Meter(3) VR302 VR301 Pin2 Pin3 CN251 L-CH R-CH Meter(2) FX-M2137ZSA/X1B/UC...
Page 72
FM ADJUSTMENT(FX-M2137ZSA/X1B/UC, FX-M2337ZSA/X1B/ES) Modulation M:MONO MOD., 400Hz 30%(22.5kHz Dev.) S1:STEREO MOD., 1kHz, L or R=30%(20.25kHz+7.5kHz Dev.) NOTE:Before proceeding to further adjustments after switching power ON, let the tuner run for ten minutes to allow the circuits to stabilize. FM SSG...
Page 73
DC V Meter(4) : 2.5±1.0V S meter 98.1 M 98.1 VR52 DC V Meter(5) : 1.75V DOLBY B NR ADJUSTMENT Test Tape Adjustment Point Adjustment Method (Switch Position) NCT-150 VR301(Lch),VR302(Rch) mV Meter(2) : –6dBm(388mV)±1dB (400Hz,200nwb/m) (DOLBY NR Switch : OFF) FX-M2137ZSA/X1B/UC...
1k ohms in series. • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. FX-M2137ZSA/X1B/UC...
Page 75
*6) Only at the time of CRG Move or 100TR Jump *7) TRK/MIN/SEC F.AGC T.AGC Gain F.bias RF AGC SPDL 1X / 2X switching (Double-speed compatibility only) *8) CRG motor voltage = 2[V] Gop measurement Forcus Mode switching / Tracking Close / CRG, TR Jump switching FX-M2137ZSA/X1B/UC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". FX-M2137ZSA/X1B/UC...
Page 77
Grating waveform Xch 20mV/div, AC Ych 20mV/div, AC FX-M2137ZSA/X1B/UC...
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. FX-M2137ZSA/X1B/UC...
Remove the four screws. Disconnect the connector and then remove the CD Mechanism Module. Removing the Sub Tuner Unit (FX-M2037ZSA/X1B/EW) (Fig.2) Remove the four screws. Disconnect the connector and then remove the Sub Tuner Unit. CD Mechanism Module Fig.2 FX-M2137ZSA/X1B/UC...
Page 80
Chassis. Chassis Fig.3 Removing the Case (Fig.4) Case Remove the two screws and then remove the Case. Removing the Cassette Mechanism Module (Fig.4) Remove the four screws and then remove the Cassette Mechanism Module. Cassette Mechanism Module Fig.4 FX-M2137ZSA/X1B/UC...
Page 81
Disconnect the connector and then remove the Connector PCB. Removing the Tuner Mother PCB (Fig.5) Remove the three screws. Straighten the tabs at two locations indicated. Remove the three screws and then remove the Tuner Mother PCB. Tuner Mother PCB Fig.5 FX-M2137ZSA/X1B/UC...
Page 82
Caution: Before installing the carriage mechanism in the frames, be sure to apply some alcohol to the dampers and set the mechanism to the clamp mode. Carriage Mechanism Damper Lower Frame Damper Damper FX-M2137ZSA/X1B/UC...
Page 83
Caution: In assembling, move the planet gear to the load/eject position before setting the feed screw in the inner holder. Washer Pickup Lock Arm Change Styling Holder Feed Screw Inner Holder Planet Gear FX-M2137ZSA/X1B/UC...
7.1.2 PCB LOCATIONS CONNECTOR PCB SUB TUNER UNIT VOLUME PCB(A) VOLUME PCB(B) TUNER UNIT KEYBOARD UNIT TUNER MOTHER PCB CD CORE UNIT(S10) SENSOR UNIT DECK UNIT FX-M2137ZSA/X1B/UC...
7.1.3 CONNECTOR FUNCTION DESCRIPTION ANTENNA Pin name Pin name Pin name CANL +15 (IG) CANH CDMR- AMPMUT CDMR+ TELMUT TELGND ANTREM TELAU FUSE +30 (BU) CDML- CDML+ FX-M2137ZSA/X1B/UC...
Page 86
SD signal input MDSENS Modulation detect input 60-64 Not used * PD6169A(FX-M2037ZSA/X1B/EW) Format Meaning C MOS IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. FX-M2137ZSA/X1B/UC...
Page 87
RRDY Ready input for RDS IC reset Reset input CAN BUS squeeze signal input BSEN Back Up power sense input igsen ACC power sense input power CD +5 control input TELM Telephone mute input csej Tape eject switch input FX-M2137ZSA/X1B/UC...
Page 88
Positive power supply terminal for analog circuit AVREF0 Signal level input BASS A/D converter input from BASS volume A/D converter input from TREBLE volume A/D converter input from BALANCE volume A/D converter input from FADER volume * PE5378A Format Meaning C MOS * S-80835CNUA-B8U FX-M2137ZSA/X1B/UC...
Page 89
BUS wake up output Squeeze signal output reset Reset input Power supply Crystal oscillator connection pin Crystal oscillator connection pin CVSS Clock VSS CVDD Clock VDD Cancellation port of stop mode CKSEL Master clock frequency select input * UPD72005GC * PE5349A FX-M2137ZSA/X1B/UC...
Page 90
CD LSI data output CD LSI data input xsck CD LSI clock output xstb CD LSI strobe output Control signal distinguishing data output Pull down(For test program) BDATA P-BUS serial data input/output bsck P-BUS serial clock input/output Format Meaning C MOS FX-M2137ZSA/X1B/UC...
Page 91
Output of focus drive PWM Output of tracking drive PWM Output of tracking drive PWM Output of thread drive PWM Output of thread drive PWM Output of spindle drive PWM Output of spindle drive PWM DGND Ground for digital circuits FX-M2137ZSA/X1B/UC...
Page 92
Output of reference voltage REFC Connected to the capacitor for output of REFOUT Reversal input of FE Output of FE ADCIN TEST Reversal input of TE Output of TE AGND Ground for the analog system PWMSW Servo PWM mode switching * UPD63712AGC FX-M2137ZSA/X1B/UC...
Page 93
Input pin for preamplifier for thread OPOUT3 CH3 preamplifier output pin OPIN3(-) Input pin for inverting input for CH3 preamplifier OPIN3(+) Input pin for non-inverting input for CH3 preamplifier PREVCC PreVcc BA5996FP NJM2391DL1-33 VREF Thermal Over current Shutdown protector FX-M2137ZSA/X1B/UC...
7.3 EXPLANATION 7.3.1 SYSTEM BLOCK DIAGRAM DISPLAY by NOKIA SAAB PART No. FRONT CENTER 4617049 FRONT Lch 4616850 FX-M2137ZSA/X1B/UC FRONT Rch DIVER UNIT GM-2416ZSA/WL FX-M2037ZSA/X1B/EW FRONT DOOR Lch by Fuba 4616926 FX-M2337ZSA/X1B/ES FRONT DOOR Rch The diversity system is REAR DOOR Lch 4616934 optional.
Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Portions to be cleaned Cleaning tools Cassette heads Pinch rollers Cleaning paper : GED-008 Capstans FX-M2137ZSA/X1B/UC...
8. OPERATIONS - FX-M2137ZSA/X1B/UC, FX-M2337ZSA/X1B/ES - RADIO PRESET RECALL PRESET CH.MEMORY POWER ON/OFF VOLUME MANUAL SEEK BALANCE BASS TREBLE FADER RADIO AUTO STORE BAND - TAPE POWER ON/OFF REWIND/FAST FORWARD VOLUME AUTO PROGRAM SEARCH BALANCE BLANK SKIP TAPE EJECT BASS...
Page 98
- CD CD EJECT DISC SELECT (MULTI CD) POWER ON/OFF VOLUME TRACK UP/DOWN BALANCE REVERSE/FAST FORWARD MANUAL/SEEK CHANGE BASS TREBLE FADER RANDOM SINGLE/MULTI SELECT FX-M2137ZSA/X1B/UC...
Page 99
- RADIO PRESET RECALL PRESET CH.MEMORY POWER ON/OFF VOLUME MANUAL SEEK BALANCE BASS TREBLE FADER RADIO AUTO STORE BAND - TAPE POWER ON/OFF REWIND/FAST FORWARD VOLUME AUTO PROGRAM SEARCH BALANCE BLANK SKIP TAPE EJECT BASS DIRECTION TREBLE FADER TAPE DOLBY FX-M2137ZSA/X1B/UC...
Page 100
- CD CD EJECT DISC SELECT (MULTI CD) POWER ON/OFF VOLUME TRACK UP/DOWN BALANCE REVERSE/FAST FORWARD MANUAL/SEEK CHANGE BASS TREBLE FADER RANDOM SINGLE/MULTI SELECT FX-M2137ZSA/X1B/UC...