Page 1 Toshiba Personal Computer Satellite P200/ P205 Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL]...
Page 2 © 2007 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein.
Page 3 This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite P200/205, referred to as the P200 Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
Page 4 For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 5 Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the computer that appears on its display is presented in the typeface below: Format complete System transferred [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 6: Table Of Contents
Chapter 2 Troubleshooting Procedures Troubleshooting Introduction..................2-3 Troubleshooting Flowchart .....................2-4 Power Supply Troubleshooting ..................2-9 Display Troubleshooting ....................2-14 Keyboard Troubleshooting.....................2-17 External USB Devices Troubleshooting ................2-19 TV-Out Failure Troubleshooting ...................2-21 TouchPad Troubleshooting ....................2-23 Speaker Troubleshooting....................2-25 [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 7 Magnetic switch Test .....................3-18 3.13 LAN Test ........................3-19 3.14 RTC Test........................3-23 3.15 Read 1394 GUID ......................3-24 3.16 Speaker EQ Check…………...………….…….….…………..……………..……..3-25 3.17 Button Test …………..……………………….………….….…………….….……….3-26 3.18 Fingerprint DOS Test ……………………..…………….….……………..….………3-27 3.19 Clear Fingerprint Registered…………………………….………………...…………...3-29 [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 8 Fingerprint Module .......................4-44 4.18 Speakers.........................4-46 4.19 Subwoofer Unit and USB Board ...................4-48 4.20 System Fan ........................4-51 4.21 VGA PCB........................4-53 4.22 System Board ........................4-55 4.23 VGA Board........................4-57 4.24 Fan and CPU .........................4-59 4.25 Display Mask.........................4-63 viii [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 9 4.26 FL Inverter Board ......................4-65 4.27 LCD Module .........................4-67 4.28 Camera and Microphone....................4-70 [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 10 Board Layout....................... B-1 Appendix C Pin Assignments ....................C-1 Appendix D Keyboard Scan/Character Codes.................D-1 Appendix E Key Layout ......................E-1 Appendix F Series Screw Torque List ..................F-1 Appendix G Reliability ......................G-1 [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 11: Chapter 1 Hardware Overview
Chapter 1 Hardware Overview [CONFIDENTIAL]...
Page 12 1 Hardware Overview [CONFIDENTIAL] 1-ii Satellite P200/P205 Series Maintenance Manual...
Page 13 Optical Disc Devices....................1-8 1.4.1 DVD-ROM & CD-RW ................1-8 1.4.2 DVD Super Multi Double Layer..............1-9 Power Supply ......................1-10 Batteries ........................1-12 1.6.1 Main Battery....................1-13 1.6.2 RTC battery ....................1-14 [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual 1-iii...
Page 14 Tables Table 1-1 2.5-inch HDD specifications ................. 1-6 Table 1-2 DVD-ROM & CD-RW drive specifications ..........1-8 Table 1-3 DVD Super Multi Double Layer drive specifications........1-9 Table 1-5 Battery specifications .................. 1-12 [CONFIDENTIAL] 1-iv Satellite P200/P205 Series Maintenance Manual...
Page 15: Features
1.1 Features 1 Hardware Overview Features The Satellite P200/ P205 Series Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight and high reliability. This computer incorporates the following features and benefits: •...
Page 16 • One 6-in-1 push-push type flash card connector and dard reader • One DDC2b compliant 15-pin VGA port , 15pins (RGB) • Express card • One RJ-11 jack for 56kbps V.92 modem • One RJ-45 jack with LED indicator • One Microphone jack [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 17 • Wireless communication switch Security • Fingerprint authentication AC Adapter • Universal AC adapter module • Liteon, API & Delta 65W, 75W, 90W adapters • Output voltage: 19Vdc • Input Voltage/Frequency range: 90-264Vac, 47-63Hz [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 18 PANs (Personal Area Networks) among your devices, and with other nearby devices like mobile computers, mobile phones, and digital cameras. • Windows Vista Home Basic/ Home Premium (32/64 bit support) • Windows Vista Business (32/64 support) • Vista Premium Logo [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 19: System Unit
• nVIDIA GeForce® Go 7600, up to 256MB VRAM (GDDR2) Audio subsystem • Realtek High Definition Audio Codec ALC861 − Microphone-in and headphone-out − Volume control: Digital control, rotary type, without mute function − Supports Microsoft Outlook Express audio [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 20: Inch Hard Disk Drive
Logical Blocks 78,140,160 117,210,240 156,301,488 195,371,568 (LBA) Rotational 5400 5400 5400 5400 speed (rpm) Toshiba HDD Buffer (MB) Hitachi HDD Buffer (MB) Fujitsu HDD Buffer (MB) Bytes per sector Table 1-1 2.5-inch HDD specifications [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 21: Table
Logical Blocks 234,441,648 312,581,808 390,720,968 488,397,168 (LBA) Rotational 5400 5400/4200 4200 4200 speed (rpm) Toshiba HDD Buffer (MB) Hitachi HDD Buffer (MB) Fujitsu HDD Buffer (MB) Bytes per sector Table 1-1 2.5-inch HDD specifications (Continued) [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 22: Optical Disc Devices
16.6 (PIO mode 4, Multiword DMA mode 2) Access time (ms) Average random access Data buffer size (Mbytes) DVD: DVD-VIDEO, DVD-ROM Formats supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, Photo CD (single/multi-session), CD-EXTRA, CD-Text Table 1-2 DVD-ROM & CD-RW drive specifications [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 23: Dvd Super Multi Double Layer
Data buffer size (Mbytes) DVD: DVD-VIDEO, DVD-ROM, DVD-R, DVD-RW, DVD-RAM, DVD+R, DVD+RW, DVD+R DL, DVD-R DL Formats supported CD-DA, CD-ROM, CD-R, CD-RW, CD-ROMXA, Photo CD (single/multi-session), CD-EXTRA, CD-Text Table 1-3 DVD Super Multi Double Layer drive specifications [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual...
Page 24: Power Supply
1.5 Power Supply Power Supply This specification defines the performance and characteristic of 65W, 75W, and 90W AC adapter power supply. It supplies a constant voltage 19V output source for Satellite P200/ P205 Series Personal Computer. A/D conversion • The EC uses 10-bit sampling for A/D conversion to determine the following values: –...
Page 25 • When a new battery is installed, the EC communicates with the E PROM in the battery to read information of the newly installed battery. Battery capacity calculation • The EC reads battery remaining and percentage capacity from the battery through SMBus. [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual 1-11...
Page 26: Batteries
Lithium-Ion 3.0V 14 mAH ML1220T10) RTC battery (Maxell Lithium-Ion 3.0V 18 mAH ML1220HT10) RTC battery (Sanyo Lithium-Ion 3.0V 15 mAH ML1220T28) RTC battery (Panasonic Lithium-Ion 3.0V 17 mAh ML1220/B) Table 1-4 Battery specifications [CONFIDENTIAL] 1-12 Satellite P200/P205 Series Maintenance Manual...
Page 27: Main Battery
4. The battery temperature is abnormal. 5. The battery SMBus communication fails. 6. The battery cell is bad. Detection of full charge A full charge is detected from the battery pack through SMBus when the battery is charging. [CONFIDENTIAL] Satellite P200/P205 Series Maintenance Manual 1-13...
Page 28: Rtc Battery
RTC battery. The RTC battery is charged by the adaptor or main battery, while the computer is powered on. Status Time Charging Time (power on) About 24 hours Data preservation period (full charge) 1 month [CONFIDENTIAL] 1-14 Satellite P200/P205 Series Maintenance Manual...
Page 29: Troubleshooting Procedures
Chapter 2 Troubleshooting Procedures...
Page 31 Wireless LAN Troubleshooting...................36 2.15 Finger printer troubleshooting ..................38 2.16 Bluetooth Troubleshooting…………………...…………………………….……….. 40 2.17 4 in 1 card Troubleshooting……………………………………………………..……42 2.18 1st HDD Troubleshooting…………..………………………………………………..44 2.19 2nd HDD Troubleshooting………………………………………………….………..46 2.20 Camera Troubleshooting……………………………………………………………..48 [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 32: Tables
Figure 2-17 1 HDD troubleshooting process…………………..……….…..…………….44 Figure 2-18 2 HDD troubleshooting process………………………………….……..….46 Figure 2-19 Camera troubleshooting process…………………..………………….…..….48 Tables Table 2-1 Battery LED ....................... 10 Table 2-2 DC-IN LED ......................11 [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 33: Troubleshooting Introduction
8. Multimeter 9. External monitor 10. USB compatible keyboard 11. Multimedia sound system with line-in and line-out ports 12. Headphones 13. USB test module and USB cable 14. Music CD [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 34: Troubleshooting Flowchart
Ask the user if a password is registered and, if it is, ask him or her to enter the password. Verify with the customer that Toshiba Windows Vista is installed on the hard disk. Operating systems that were not preinstalled by Toshiba can cause the computer to malfunction.
Page 35 R u n C M 1 6 5 .E X E a n d se le c t th e H A R D D IS K ite m . Y es Figure 2-1 Troubleshooting flowchart (1/2) [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 36 Is an error detected by any of the an error, perform the diagnostics tests? appropriate procedure as outlined below. System is normal Figure 2-1 Troubleshooting flowchart (2/2) [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 37 6. If an error is detected by the modem test, perform the Modem Troubleshooting Procedures in Section 2.11. 7. If an error is detected by Camera test, perform the Camera Trouble shooting Procedures in Section 2.15. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 38 6. If an error is detected when using the IEEE1394 device, perform the IEEE1394 device Troubleshooting procedures in Section 2.13. 7. If an error is detected when using the Wireless LAN, perform the Wireless LAN Troubleshooting procedures in Section 2.14. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 39: Power Supply Troubleshooting
P erform internal connection A re the internal power check connections secure? (P rocedure 5) Y es R eplace system board E N D Figure 2-2 Power Supply Troubleshooting Process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 40 2 seconds) without the AC power connected. Amber color off Battery not in low or critical low state; It’s in discharging state [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 41 Connect a new AC adaptor. If the problem is not resolved, go to Check 2. Check 2 Insert a new battery. If the problem is still not resolved, go to Procedure 3. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 42 Make sure the battery pack is installed in the computer correctly. If the battery is properly installed and the battery LED still does not light, go to Procedure 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 43 Make sure that the battery cable is firmly connected to the system board. If it is connected firmly, go to Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 44: Display Troubleshooting
( P r o c e d u r e 3 ) R e p la c e s y s te m b o a r d E N D Figure 2-3 Display troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 45 Refer to Chapter 3, Tests and Diagnostics for details. If an error is detected, go to Procedure 3. If an error is not detected, the display is functioning properly. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 46 Replace the CPU with another of the same specifications. If the problem still exists, perform Check 6. Check 6 The system board may be damaged. Replace it with a new one. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 47: Keyboard Troubleshooting
( P r o c e d u r e 3 ) R e p la c e s y s te m b o a r d E N D Figure 2-4 Keyboard troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 48 Chapter 4. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 49: External Usb Devices Troubleshooting
R e p la c e s y s te m b o a r d ( P r o c e d u r e 2 ) E N D Figure 2-5 External USB device troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 50 Go to Procedure 2. Procedure 2 Replace system board If the error persists, the system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 51: Tv-Out Failure Troubleshooting
Y es R e p la c e s y s te m b o a r d E N D Figure 2-6 TV-out troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 52 If the replacement set does not work the system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 53: Touchpad Troubleshooting
2 Troubleshooting Procedures TouchPad Troubleshooting START TouchPad connection check (Procedure 1) TouchPad replacement check (Procedure 2) Replace system board Figure 2-7 Touchpad troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 54 The TouchPad unit or FPC may be defective or damaged. Replace each with a new one following the steps in Chapter 4. If the FDD is still not functioning properly, replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 55: Speaker Troubleshooting
Figure 2-1 Perform earphone test (Procedure 2) Do earphones function correctly? Perform connection check (Procedure 3) Perform replacement check (Procedure 4) Replace system board Figure 2-8 Speaker troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 56 If the stereo speakers don't sound properly, the stereo speakers may be defective or damaged. Replace them with new ones. If the stereo speakers still do not work properly, try replacing in turn the audio board and system board. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 57: Optical Drive Troubleshooting
(Procedure 2) Perform software check (Procedure 3) Perform diagnostic test (Procedure 4) Perform connection and replacement check (Procedure 5) Replace system board Figure 2-9 Optical drive troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 58 The audio test program stored in the Diagnostics Disk will test the drive’s ability to play an audio CD. See Chapter 3 for details. If any errors occur while executing the diagnostic program, go to Procedure 5. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 59 Chapter 4, Replacement Procedures. If the drive is still not functioning properly, perform Check 3. Check 3 The system board may be damaged. Replace it with new one following the instructions in Chapter 4, Replacement Procedures. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 60: Modem Troubleshooting
Check / replace Computer unable to telephone line and detect telephone signal? connections Perform connection check (Procedure 2) Perform replacement check (Procedure 3) Replace system board Figure 2-10 Modem troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 61 The modem card or RJ-11 jack may be faulty. Try replacing them. If the problem persists, the system board may be defective or damaged. Replace the System Board with a new one following the steps in Chapter 4, Replacement Procedures. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 62: Express Card Troubleshooting
Do errors occur during Express card unit is express card test? not faulty. Perform express card socket replacement check (Procedure 2) Replace system board Figure 2-11 Express card troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 63 Procedures and replace the socket. If the problem persists, the system board may be defective or damaged. Replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 64: Ieee 1394 Troubleshooting
Was an IEEE 1394 problem detected? faulty. Continue troubleshooting - refer to Figure 2.1 Perform connection and replacement check (Procedure 3) Replace system board Figure 2-12 IEEE 1394 troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 65 The transmission cable may be damaged. Replace with a good cable. If the malfunction persists, go to Check 4 Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 66: Wireless Lan Troubleshooting
Was a wireless LAN problem delected? troubleshooting - refer to Figure 2.1 Perform connector and replacement check (Procedure 2) Replace wireless LAN antenna/unit Replace system board Figure 2-13 Wireless LAN troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 67 Chapter 4. If the problem still exists, perform Check 4. Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 68: Finger Printer Troubleshooting
2 Troubleshooting Procedures 2.15 Fingerprint Troubleshooting Figure 2-14 Fingerprint troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 69 Chapter 4. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 70: Bluetooth Troubleshooting
(P roce dure 2) Re pla ce Blue tooth a nte nna m oudle . R e pla ce s ys te m boa rd Figure 2-15 Bluetooth troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 71 Chapter 4. If the problem still exists, perform Check 4. Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 72: In 1 Card Troubleshooting
4 IN 1 unit is not IN 1 CARD test? faulty. Perform 4 IN 1 card socket replacement check (Procedure 2) Replace system board Figure 2-16 4 in 1 card troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 73 Procedures and replace the socket. If the problem persists, the system board may be defective or damaged. Replace the system board with a new one following the steps in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 74: 1St Hdd Troubleshooting
2 Troubleshooting Procedures 2.17 1 HDD Troubleshooting Figure 2-17 HDD troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 75 Chapter 4. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 76: 2Nd Hdd Troubleshooting
2 Troubleshooting Procedures 2.18 2 HDD Troubleshooting Figure 2-18 2 HDD troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 77 Chapter 4. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 78: Camera Troubleshooting
2 Troubleshooting Procedures 2.19 Camera Troubleshooting Figure 2-19 Camera troubleshooting process [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 79 Chapter 4. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4. [CONFIDENTIAL] Satellite P200 / P205 /Satellite Pro P200 Series Maintenance Manual...
Page 80: Chapter 3 Tests And Diagnostics
3. Tests and Diagnostics Chapter 3 Tests and Diagnostics Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 81 Read 1394 GUID......................3-24 3.16 Speaker EQ Check…………...………….…….……………..……………..……..3-25 3.17 Button Test …………..……………………….………….……………….….……….3-26 3.18 Fingerprint DOS Test ……………………..…………….………………..….………3-27 3.19 Clear Fingerprint Registered…………………………….………………...…………...3-29 3.20 HDD Test........................3-30 3.21 HDD Test………………………….………………………..…………….………..3-33 3.22 Front Edge Logo check ……………….………………………..…………….………..3-36 Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 82: The Diagnostic Test
A formatted working diskette for the floppy disk drive test (Floppy Disk Drive Test) A data CD disc (ODD Test) A LAN loopback The following sections explain how to execute the Test & Diagnostic Program and detail the tests within the program. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 83: Executing The Diagnostic Test
K. LAN TEST L. RTC TEST M. IEEE1394 CODE TEST N. SPEAKER EQ CHECK TEST O. BUTTON TEST P. FINGERPRINT TEST Q. CLEAR FP REGISTERED R. 1 HDD TEST S. 2 HDD TEST Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 84 3. Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will appear: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 85 Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “Y” key pressed. It will skip this process if “N” key pressed. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 86 And then it will check if it’s necessary to leave this program. Program will quit when “Y” key pressed and it will go back main menu for next test if “N” key pressed. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 87: Display Configuration
Panel ID HDD type & capacity (Vendor ID. Model .Firmware) VRAM size / VGA CHIP TYPE Battery cell (6cell;9cell;12cell) Wireless type LAN Type 1394 Bluetooth SKU ID The screen should display as below: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 88: Speaker Audio Test
OK within 3 times “Beep” sound generated. NOTE: Remember to tune up the volume as “Maximum” before this test starts. The screen should display as below, indicating whether the test is passed or failed after the question. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual...
Page 89: Fan On/Off Test
The computer will stop the fan working after any key pressed. Feel the wind or listen the sound to check if the fan is “OFF”. The screen should display as below, indicating whether the test is passed or failed after the question. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-10...
Page 90: Main Battery Charge Test
- “Battery Is Full” showed when “remain charge capacities” is 100% The screen should display as below, if the charge function is OK, will show:. If the charge function is NG, the screen will display as: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-11...
Page 91: Fdd Test
NOTE: The write-protected device of this formatted diskette should be “Disable”. The subtests run automatically. NOTE: Press “Esc” key can skip the current subtest. The screen should display as below, indicating whether the subtests pass or fail when finished. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-12...
Page 92: Odd Test
The ODD test includes two subtests of the: 1. Random read/partial sequential read function 2. Eject ODD door The screen should display as below, indicating whether the subtests pass or fail when finished. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-13...
Page 93: Keyboard Test
NOTE: The “Fn” key cannot be tested in the keyboard test. To determine whether the “Fn” key is working correctly, press “Fn+F6 ” or “Fn+F7 ” keys to check if LCD display brightness change gradually. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-14...
Page 94: Mouse (Pad) Test
The Touch Pad button subtest allows users to test their Touch Pad buttons. If the buttons are clicked, the cursors should appear in the corresponding box of the button figure that is displayed on the screen as below. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-15...
Page 95 NOTE: The above figure has three compartments although the Touch Pad installed may only have two buttons. In this case, the central compartment in the figure does not correspond to any button. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-16...
Page 96: Lcd Pixels Mode Test
- including 320*200 (4/16/256 colors), 640*200 (2/16 colors), 640*350 (2/16 colors), 640*480 (2/16/256 colors), 800*600 (256 colors) and 1024*768 (256 colors). The screen should display as below, indicating whether the test is passed or failed after the question. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-17...
Page 97: Magnetic Switch Test
Follow below steps to run this test: 1. Close the LCD cover. 2. Heard 3 “Beep” sound happened during LCD closed. 3. Open the LCD. Then it will indicate whether the test is passed or failed. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-18...
Page 98: Lan Test
Line Frame – 1514 Bytes. Line Speed – 100Mbps or 10 Mbps. Bus ID – it’s “4”. The LAN test includes three subtests of the: 1. Speed1000 2. Speed100 3. Speed10 The subtests run automatically. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-19...
Page 99 3. Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-20...
Page 100 3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-21...
Page 101: Rtc Test
Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-22...
Page 102: Read 1394 Guid
This test will check if the computer’s EEPROM 1394GUID code is correct. NOTE: Must open the RAM Door to see RAM connector GUID bar code before test item begins. The figure below will be displayed: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-23...
Page 103: Read 1394 Guid
1. Read EQ Type from EEPROM 2. Re-Write EQ Type to EEPROM NOTE: To execute this test, you must select speaker type (Harman or No brand). The figure below will be displayed: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-24...
Page 104: Button Test
Press each of the buttons on the front panel in turn. A yellow bar will appear on the relevant section of the figure if the button passes the test. Press Ctrl +C to quit the test. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-25...
Page 105: Fingerprint Dos Test
Step2. Swipe your finger a 2 time to enroll. Step3. Swipe your finger a 3 time to enroll. Step4. The test program auto compares 1 , 2nd and 3 finger swipes to enroll. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-26...
Page 106 3. Tests and Diagnostics Step5. Swipe your finger then the test program will verify it. Step6. Verify pass, Step7. Select your test result to show “PASS” or “Fail”. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-27...
Page 107: Clear Fingerprint Registered
" to clear all information in TBX module The subtests run step by step: (As below) Step1: Step2: Display Notice for clear registered. Step3: The information below is the utility auto run. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-28...
Page 108 Step5: If you choice “Y”, the system will reboot. If you choice “N”, the system will show Notice again (see be photo). You can press any key to go back test MEMU list. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-29...
Page 109: Hdd Test
After the choice HDD test, Screen would display as below: If input password is Right, the screen would display as below: Press any key to test HDD function, the screen would display as below: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-30...
Page 110 The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-31...
Page 111 3. Tests and Diagnostics If the picture shows as below, it means he HDD function is NG Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-32...
Page 112: Nd Hdd Test
After the choice HDD test, Screen would display as below: If input password is Right, the screen would display as below: Press any key to test HDD function, the screen would display as below: Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-33...
Page 113 The screen will display as below picture to show the subtest is passed or failed when finished: If it is show the picture as below, it means HDD function is OK Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-34...
Page 114 3. Tests and Diagnostics If the picture shows as below, it means he HDD function is NG Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-35...
Page 115: Front Edge Logo Check
If have the logo, please key 1 to set the Front Edge Logo. If not have the logo, please key 2 to disable the Front Edge Logo. NOTE: The AC adaptor should be connected to successfully run this test. Satellite P200/P205 /Satellite Pro P200 Series Maintenance Manual 3-36...
Page 116: Chapter 4 Replacement Procedures
Chapter 4 Replacement Procedures [CONFIDENTIAL]...
Page 117 4 Replacement Procedures [CONFIDENTIAL] / P205 4-ii Satellite P200 Series Maintenance Manual...
Page 118 VGA Board ......................4-57 4.24 Fan and CPU ......................4-59 4.25 Display Mask ......................4-63 4.26 FL Inverter Board ....................4-65 4.27 LCD Module ......................4-67 4.28 Camera and Microphone..................4-70 [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-iii...
Page 119 Removing the keyboard cover..............4-27 Figure 4-27 Removing the keyboard cover..............4-27 Figure 4-28 Removing the keyboard screws..............4-28 Figure 4-29 Disconnecting the keyboard cable..............4-28 Figure 4-30 Disconnecting cables..................4-30 Figure 4-31 Removing the strip cover ................4-31 [CONFIDENTIAL] / P205 4-iv Satellite P200 Series Maintenance Manual...
Page 120 Removing the fan..................4-51 Figure 4-61 Removing the VGA PCB FFC cable ............4-53 Figure 4-62 Removing the VGA PCB screw and the hexagonal screws ......4-53 Figure 4-63 Removing the VGA PCB................4-54 [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 121 Removing the LCD Module .................4-68 Figure 4-83 Removing the bracket screws...............4-68 Figure 4-84 Removing the LVDS cable................4-69 Figure 4-85 Removing the CMOS cable................4-70 Figure 4-86 Removing the camera module..............4-70 Figure 4-87 Removing the microphone ................4-71 [CONFIDENTIAL] / P205 4-vi Satellite P200 Series Maintenance Manual...
Page 122: General
Button Board Module Top Cover Display Mask Wireless LAN Touch Pad Fingerprint Module Speakers FL Inverter Board Module Subwoofer USB Board System Fan System Board Camera and VGA Board Heat Sink Microphone Module [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 123 Button Board Module Top Cover Display Mask Wireless LAN Touch Pad Fingerprint Module Speakers FL Inverter Board Module Subwoofer USB Board System Fan System Board Camera and VGA Board Heat Sink Microphone Module [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 124 DANGER: Always use the lithium ion battery pack or backup battery that is authorized by Toshiba or compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode.
Page 125 The computer contains many sharp edges and corners, so be careful not to injure yourself. 10. After you have replaced an FRU, make sure the computer is functioning properly by performing the appropriate test on the FRU you have fixed or replaced. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 126 FRU. After installing an FRU in the computer, confirm that the FRU and the computer are functioning properly. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 127 Tweezers, to lift out screws that you cannot grasp with your fingers. ESD mats for the floor and the table you are working on. ESD wrist strap or heel grounder. Anti-static carpeting or flooring. Air-ionizers in highly static sensitive areas. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 128: Battery
Slide the battery bay latch to release the battery pack and then remove the battery pack from the bay. Figure 4-2 Unlocking the battery lock NOTE: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to Toshiba. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 129 WARNING: The battery is a lithium ion battery and can explode if not properly replaced, used, handled or disposed of. Use only batteries recommended by Toshiba as replacements. Slide the battery pack into the battery bay. The battery bay latch clicks into place automatically.
Page 130: Pc Card
Push the eject button again to pop the PC card out slightly. Grasp the PC card and pull it out from the slot. Figure 4-3 Removing the PC card Press the eject button back into place, if necessary. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual...
Page 131: Installing The Pc Card
Make sure the eject button does not stick out. Push it back into place if required. Insert the PC card in the slot and gently press to ensure a firm connection. Figure 4-4 Installing the PC card [CONFIDENTIAL] / P205 4-10 Satellite P200 Series Maintenance Manual...
Page 132: Memory Card
Press the memory card gently into the socket until it pops out. Figure 4-5 Pressing the memory card Grasp the memory card and remove it. Figure 4-6 Removing the memory card [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-11...
Page 133: Installing The Memory Card
Inserting the Memory Card To insert the memory card, follow the steps below: Insert the memory card in the slot and gently press to ensure a firm connection. Figure 4-7 Installing the memory card [CONFIDENTIAL] / P205 4-12 Satellite P200 Series Maintenance Manual...
Page 134: Hdd
Follow the steps below to remove the main HDD module: Turn the computer upside down. Remove the black M2.5x4 screw to release the main HDD door. Main HDD Figure 4-9 Releasing the main HDD door screw [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-13...
Page 135: Figure
Pull up and lift the HDD door to remove it. Figure 4-10 Removing the main HDD door Pull out the black Mylar tab to remove the HDD unit. Figure 4-11 Removing the main HDD [CONFIDENTIAL] / P205 4-14 Satellite P200 Series Maintenance Manual...
Page 136 Pull the HDD outwards and remove the four silver M3x3 screws that secure the HDD case and brackets to the HDD. Figure 4-12 Removing the HDD screws from brackets Remove the HDD from the HDD case. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-15...
Page 137: Releasing The Secondary Hdd Door Screw
Release the two black M2.5x4 screws to release the secondary HDD door. Secondary Figure 4-13 Releasing the secondary HDD door screw Pull up and lift the HDD door to remove it. Figure 4-14 Removing the secondary HDD door [CONFIDENTIAL] / P205 4-16 Satellite P200 Series Maintenance Manual...
Page 138: Removing The Secondary Hdd
Seat the secondary HDD in the HDD case and brackets, and secure it with four silver M3×3 screws. Insert the secondary HDD unit into the HDD slot on the right. Secure the HDD door with two black M2.5x4 screws. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-17...
Page 139: Expansion Memory
Release the black non-separate screw M2.5x6.5 screw securing the memory module socket cover. Figure 4-16 Releasing the cover screw Slide your fingernail or a thin object under the cover and lift it off. Figure 4-17 Removing the expansion memory module cover [CONFIDENTIAL] / P205 4-18 Satellite P200 Series Maintenance Manual...
Page 140 Repeat steps 3 and 4 to remove the second memory expansion module in the same way. CAUTION: Do not touch the connectors on the expansion memory module or on the computer. Debris on the connectors may cause memory access problems. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-19...
Page 141 Push the module down so it lies flat. The latches on either side will click into place to secure the module. Seat the cover and secure its screw. [CONFIDENTIAL] / P205 4-20 Satellite P200 Series Maintenance Manual...
Page 142: Modem
Remove the two black M2.5x3 screws securing the modem to the chassis. Figure 4-20 Removing the modem module screws Disconnect the modem connector from the modem module. Figure 4-21 Removing the modem connector [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-21...
Page 143 Connect the modem connector on the system board to the modem module. Fit the modem onto its connector and secure it with two black M2.5x3 screws. Replace the M2.5x4 screw to fix the secondary HDD cover. [CONFIDENTIAL] / P205 4-22 Satellite P200 Series Maintenance Manual...
Page 144: Optical Drive Module
Remove the black M2.5x8 screw securing the optical drive module. Figure 4-23 Removing the optical drive screw Use your hand to push the module bracket and then slide the module from the bay. Figure 4-24 Removing the optical drive [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-23...
Page 145 To install a device in the optical drive module bay, follow the steps below and refer to the figure in the preceding section. 1. Slide the device into the optical drive module bay. 2. Use the black M2.5x8 screw to secure the optical drive module. [CONFIDENTIAL] / P205 4-24 Satellite P200 Series Maintenance Manual...
Page 146: Optical Drive
Removing the optical drive bracket NOTE: The small arrow shown on the metal bracket indicates the top side of the optical bracket. Keep this in mind when removing or installing the drive. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-25...
Page 147 Position the optical drive bracket plate so that it is aligned with the rear panel of optical drive. Secure the optical drive bracket plate with two M2x2.5 screws. Install the optical drive module into the bay as described in the preceding section. [CONFIDENTIAL] / P205 4-26 Satellite P200 Series Maintenance Manual...
Page 148: Keyboard
Insert a thin tool into the gap between the keyboard cover and keyboard to lever the keyboard cover up. Figure 4-26 Removing the keyboard cover Remove the keyboard cover. Figure 4-27 Removing the keyboard cover [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-27...
Page 149: Disconnecting The Keyboard Cable
Removing the keyboard screws Slide the keyboard forward to lift it out, revealing the keyboard cable underneath. Disconnect the keyboard cable and remove the keyboard. Figure 4-29 Disconnecting the keyboard cable [CONFIDENTIAL] / P205 4-28 Satellite P200 Series Maintenance Manual...
Page 150 Set the keyboard in place and secure it with four black M2x4 screws. Set the keyboard cover in place and press down to secure the keyboard cover until the latches engage. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-29...
Page 151: Display Assembly
To remove the display assembly, first remove the battery, keyboard, and any optional devices. Then follow the steps below: Disconnect the LVDS cable, function button board cable, wireless LAN antennas, CMOS cable, and microphone cable from the system board. Figure 4-30 Disconnecting cables [CONFIDENTIAL] / P205 4-30 Satellite P200 Series Maintenance Manual...
Page 152 Remove the strip cover from the computer chassis. Figure 4-31 Removing the strip cover Remove two M2.5x8 black screws securing the LCD assembly from the rear side. Figure 4-32 Removing the rear screws [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-31...
Page 153 4.11 Display Assembly Remove two M2.5x8 screws securing the LCD assembly to the top cover. Figure 4-33 Removing the front screws Remove the LCD assembly. Figure 4-34 Removing the display assembly [CONFIDENTIAL] / P205 4-32 Satellite P200 Series Maintenance Manual...
Page 154 Replace the strip cover. Connect the LVDS cable, function button board cable, wireless LAN antennas, CMOS cable, and microphone cable to their respective sockets on the system board. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-33...
Page 155: Function Button Board
3. Slide out the function button board in direction of the arrow. Figure 4-36 Sliding out the function button board 4. Lift the function button board up. Figure 4-37 Removing the function button board [CONFIDENTIAL] / P205 4-34 Satellite P200 Series Maintenance Manual...
Page 156 2. Secure the board with one M2.5x4 screw. 3. Turn the strip cover over and replace it on the top chassis. 4. Connect the other end of the FCC cable to the connector on the system board. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-35...
Page 157: Wireless Lan Unit
Grasp the wireless LAN unit and pull it out. Figure 4-39 Removing the wireless LAN card CAUTION: Do not touch the connectors on the wireless LAN unit or on the computer. Debris on the connectors may cause malfunction. [CONFIDENTIAL] / P205 4-36 Satellite P200 Series Maintenance Manual...
Page 158 Debris on the connectors may cause malfunction. Secure the wireless LAN unit to the system board with two M2x2.5 screws. Attach the white antenna to the Main connector, and the black antenna to the Aux connector. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-37...
Page 159: Bluetooth
To install the Bluetooth module, follow the steps below and refer to the figures in the preceding section. Seat the Bluetooth module on the top chassis in place. Connect the Bluetooth cable to the module. [CONFIDENTIAL] / P205 4-38 Satellite P200 Series Maintenance Manual...
Page 160: Top Cover
Removing the top cover (back panel screws) Turn the computer over again and detach the two speaker cables, system fan cable, touch pad FFC cable, fingerprint unit FFC cable, and the Bluetooth cable from the top cover. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-39...
Page 161: Figure
• M2.5x8: four screws • M2.5x6: two screws • M2.5x20: one screw Figure 4-44 Removing the top cover (front panel screws) Lift off the top cover. Figure 4-45 Removing the top cover [CONFIDENTIAL] / P205 4-40 Satellite P200 Series Maintenance Manual...
Page 162 Secure the top cover with two M2.5x6 screws, four M2.5x8 screws, and one M2.5x20 screw. Turn the computer upside down and secure eleven M2.5x8 screws, seven M2.5x4 screws, and one M2.5x3 screw. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-41...
Page 163: Touch Pad
Remove five M2.5x3 screws securing the Touch Pad bracket to the rear side of the top cover. Figure 4-46 Removing the touch pad screw Disconnect the Touch Pad FFC cable from the Touch Pad. Figure 4-47 Disconnecting the touch pad FFC cable [CONFIDENTIAL] / P205 4-42 Satellite P200 Series Maintenance Manual...
Page 164 With the top cover upside down, place the Touch Pad and the Track Pad bracket in position. Secure the Touch Pad bracket with five M2.5x3 screws. Connect the Touch Pad FFC cable to the Touch Pad. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-43...
Page 165: Fingerprint Module
Remove four M2.5x3 screws securing the Fingerprint Module Bracket to the rear side of the top cover. Figure 4-49 Removing the fingerprint module bracket screws Remove the bracket. Figure 4-50 Removing the fingerprint module bracket [CONFIDENTIAL] / P205 4-44 Satellite P200 Series Maintenance Manual...
Page 166 Turn the top cover upside down and place the Fingerprint Module and the Fingerprint Module Bracket in position on top. Secure the Fingerprint Module bracket with four M2.5x3 screws. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-45...
Page 167: Speakers
Remove the two M2.5x4 screws securing the right speaker to the rear side of the top cover. Figure 4-52 Removing the speaker screws Remove the speakers. Figure 4-53 Removing the speakers [CONFIDENTIAL] / P205 4-46 Satellite P200 Series Maintenance Manual...
Page 168 Turn the top cover upside down and place the speakers in position on top. Secure each speaker with two M2.5x4 screws. Turn over and install the top cover onto the system board. Connect the speaker cables (black and red) to the system board. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-47...
Page 169: Subwoofer Unit And Usb Board
Remove the two screws securing the subwoofer unit to the chassis. Figure 4-54 Removing the subwoofer screws Remove the USB board cable and subwoofer cable. Figure 4-55 Disconnecting the USB board cable and subwoofer cable [CONFIDENTIAL] / P205 4-48 Satellite P200 Series Maintenance Manual...
Page 170: Removing The Subwoofer Unit
Removing the subwoofer unit Remove the M2.5x4 screw securing the USB board to the chassis. Figure 4-57 Removing the USB board screw Remove the USB board. Figure 4-58 Removing the USB board [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-49...
Page 171 Connect the USB board cable to the system board. Secure the USB board with one M2.5x4 screw. Seat the subwoofer unit in place. Connect the subwoofer cable to the system board. Secure the subwoofer unit with four screws. [CONFIDENTIAL] / P205 4-50 Satellite P200 Series Maintenance Manual...
Page 172: System Fan
Remove the three M2.5x4 screws securing the system fan to the chassis. Figure 4-59 Removing the fan screws Lift out the fan. Figure 4-60 Removing the fan [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-51...
Page 173 To install the system fan, follow the steps below and refer to the figures in the preceding section. Seat the system fan in the chassis. Secure the fan with three M2.5x4 screws. [CONFIDENTIAL] / P205 4-52 Satellite P200 Series Maintenance Manual...
Page 174: Vga Pcb
Remove the M2x6 screw securing the VGA PCB. Then remove the two hexagonal VGA screws from the left side of the computer. Figure 4-62 Removing the VGA PCB screw and the hexagonal screws [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-53...
Page 175 Replace the M2x6 screw to secure the VGA PCB. Replace the two hexagonal screws to secure the VGA port. Connect the VGA PCB FFC cable to its socket on the system board. [CONFIDENTIAL] / P205 4-54 Satellite P200 Series Maintenance Manual...
Page 176: System Board
VGA PCB, then follow the steps below: Remove the two M2x4 screws securing the system board. Figure 4-64 Removing the system board screws Remove the DC connector from its socket. Figure 4-65 Removing the DC power cable [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-55...
Page 177 Seat the system board in the chassis. Take care to align all the ports and connectors in their respective openings on the chassis. Replace the two M2x4 screws to secure the system board. Connect the DC power cable to the socket on the system board. [CONFIDENTIAL] / P205 4-56 Satellite P200 Series Maintenance Manual...
Page 178: Vga Board
Turn the system board over and remove the three M2.5x4 screws securing the VGA board. Figure 4-67 Removing the VGA board screws Remove the VGA board from the system board. Figure 4-68 Removing the VGA board [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-57...
Page 179 Connect the heat sink to the VGA board by securing it with four screws. Follow the order indicated by the numbers on the heat sink to tighten the screws. Seat the VGA board and secure it by placing the three M2.5x4 screws and tightening them. [CONFIDENTIAL] / P205 4-58 Satellite P200 Series Maintenance Manual...
Page 180: Fan And Cpu
Follow the order indicated by the numbers on the heat sink in reverse to remove the screws. Figure 4-70 Removing the heat sink screws Lift and remove the heat sink from the system board. Figure 4-71 Removing the heat sink [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-59...
Page 181 Turn over and remove the fan connector and two M2.5x3 screws from the system board. Figure 4-72 Removing the fan connector and screws Remove the fan module. Figure 4-73 Removing the fan [CONFIDENTIAL] / P205 4-60 Satellite P200 Series Maintenance Manual...
Page 182 CPU socket to unlock the CPU. Figure 4-74 Turning the CPU cam Gently lift out the CPU. Figure 4-75 Removing the CPU [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-61...
Page 183 Seat the heat sink over the CPU and secure with four screws in the order indicated on the heat sink. Seat the fan module and secure with the two M2.5x3 screws on the front side of the system board. Attach the fan connector. [CONFIDENTIAL] / P205 4-62 Satellite P200 Series Maintenance Manual...
Page 184: Display Mask
Remove two M2.5x6 silver screws on the upper display mask and two M2.5x8 black screws on the lower display mask. Figure 4-76 Removing the display mask screws [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-63...
Page 185 To install the display mask, follow the steps below and refer to the figures in the preceding section. Seat the display mask and secure the snaps on each side. Secure the display mask with two silver M2.5x6 screws and two black M2.5x8 screws. [CONFIDENTIAL] / P205 4-64 Satellite P200 Series Maintenance Manual...
Page 186: Removing The Fl Inverter Board Screws
Remove the black M2x4 screw securing the FL invert board to the top chassis. Figure 4-78 Removing the FL inverter board screws Disconnect the two connectors on either side of the FL invert board. Figure 4-79 Removing the connectors [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-65...
Page 187 Seat the FL inverter board in the top chassis. Secure the FL inverter board with one black M2x4 screw to the top chassis. Connect the two connectors on either side of the board. [CONFIDENTIAL] / P205 4-66 Satellite P200 Series Maintenance Manual...
Page 188: Removing The Lcd Module
Unhook all cables from the fasteners around the edge of the top chassis. Remove six M2.5x6 screws securing the LCD module to the top chassis. Figure 4-81 Removing the LCD module screws [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-67...
Page 189: Figure
Remove eight M2x3 screws securing the LCD module bracket to the LCD module. Figure 4-83 Removing the bracket screws NOTE: If the LCD module malfunctions, remove the LCD cable and LCD bracket. Then replace the whole LCD module unit. [CONFIDENTIAL] / P205 4-68 Satellite P200 Series Maintenance Manual...
Page 190: Figure
Connect the two connectors on either side of the FL inverter board. Hook all the cables in the fasteners around the edge of the top chassis. Thread the thinner cables first, followed by the thicker ones. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-69...
Page 191: Removing The Cmos Cable
Remove the CMOS cable from the camera module. Figure 4-85 Removing the CMOS cable Remove the camera module by gently peeling it away from its adhesive backing. Figure 4-86 Removing the camera module [CONFIDENTIAL] / P205 4-70 Satellite P200 Series Maintenance Manual...
Page 192: Removing The Microphone
Fix the camera module to the adhesive backing at the top chassis. Connect the CMOS cable to the camera module. Push the microphone into place in its respective bracket. [CONFIDENTIAL] / P205 Satellite P200 Series Maintenance Manual 4-71...
Page 193: Appendix A Handling The Lcd Module
LCD cover before securing the module with screws. Do not force the module into place, because stress can affect its performance. Note: The panel’s polarized surface is easily scratched and damaged, so handle it carefully. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 194 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 195 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 196 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 197 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 198 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 199: Appendix B Board Layout
Appendix B Appendix B Board Layout B.1 System Board (FRDSY*) Top View JP39 JP2 PJP1 JP17 JP23 JP30 JP37 JP29 JP41 JP27 JP16 JP35 JP28 JP34 JP19 JP12 JP40 JP36 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 200 B.2 System Board (FRDSY*) Button View PJP2 JP13 JP33 JP26 JP38 JP10 JP25 JP18 JP14 JP15 JP24 JP11 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 201 JP29 ROBSON Card conn JP30 Bluetooth conn JP33 USB conn JP34 USB/B conn JP35 Keyboard conn JP36 Touch Pad conn JP37 SW/B conn JP38 MDC conn JP39 CRT/B conn JP40 Int. MIC conn [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 202 Table B-2 System board ICs (top and bottom) Number Name LAN RTL8101E/ RTL8111B North bridge 945GM/945PM Clock Generator ICS9LPRS325CKLFT EC KB910 South bridge ICH7 BIOS ROM LAN transformer Card bus controller TI PCI8402 HD codec AC861 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 203: Appendix C Pin Assignments
Table C-1 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name Pin No. Signal Name VREF DQS0# DQS0 DQ12 DQ13 DQS1# DQS1 CK0# DQ10 DQ14 DQ11 DQ15 DQ16 DQ20 DQ17 DQ21 DQS2# [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 204 Table C-1 SODIMM I/F pin assignments (200-PIN) (2/4) Pin No. Signal name Pin No. Signal Name DQS2 DQ18 DQ22 DQ19 DQ23 DQ24 DQ28 DQ25 DQ29 DQS3# DQS3 DQ26 DQ30 DQ27 DQ31 CKE0 NC/CKE1 NC/A15 NC/A14 A10/AP RAS# CAS# ODT0 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 205 DQ36 DQ33 DQ37 DQS4# DQS4 DQ38 DQ34 DQ39 DQ35 DQ44 DQ40 DQ45 DQ41 DQS5# DQS5 DQ42 DQ46 DQ43 DQ47 DQ48 DQ52 DQ49 DQ53 NC,TEST CK1# DQS6# DQS6 DQ50 DQ54 DQ51 DQ55 DQ56 DQ60 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 206: Table
Pin No. Signal name Pin No. Signal Name DQ57 DQ61 DQS7# DQS7 DQ58 DQ59 DQ62 DQ63 VDDSPD Table C-2 TV-OUT I/F pin assignments (4-pin) Pin No. Signal name Pin No. Signal Name TV_LUMA_L TV_CRMA_L [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 207 +VGA_B+ +1.8VS +VGA_B+ +1.8VS +VGA_B+ +1.8VS +VGA_B+ +1.8VS +VGA_B+ +1.8VS +VGA_B+ +1.8VS +1.8VS +3VS +1.8VS +3VS +1.8VS +3VS +1.8VS +1.8VS +1.5VS +1.5VS +1.8VS +1.5VS +1.8VS +1.5VS +1.8VS +1.8VS +5VALW PCIE_GTX_C_MRX_P15 PCIE_MTX_C_GRX_P15 PCIE_GTX_C_MRX_N15 PCIE_MTX_C_GRX_N15 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 208 PCIE_MTX_C_GRX_N12 PCIE_GTX_C_MRX_P11 PCIE_MTX_C_GRX_P11 PCIE_GTX_C_MRX_N11 PCIE_MTX_C_GRX_N11 PCIE_GTX_C_MRX_P10 PCIE_MTX_C_GRX_P10 PCIE_GTX_C_MRX_N10 PCIE_MTX_C_GRX_N10 PCIE_GTX_C_MRX_P9 PCIE_MTX_C_GRX_P9 PCIE_GTX_C_MRX_N9 PCIE_MTX_C_GRX_N9 PCIE_GTX_C_MRX_P8 PCIE_MTX_C_GRX_P8 PCIE_GTX_C_MRX_N8 PCIE_MTX_C_GRX_N8 PCIE_GTX_C_MRX_P7 PCIE_MTX_C_GRX_P7 PCIE_GTX_C_MRX_N7 PCIE_MTX_C_GRX_N7 PCIE_GTX_C_MRX_P6 PCIE_MTX_C_GRX_P6 PCIE_GTX_C_MRX_N6 PCIE_MTX_C_GRX_N6 PCIE_GTX_C_MRX_P5 PCIE_MTX_C_GRX_P5 PCIE_GTX_C_MRX_N5 PCIE_MTX_C_GRX_N5 PCIE_GTX_C_MRX_P4 PCIE_MTX_C_GRX_P4 PCIE_GTX_C_MRX_N4 PCIE_MTX_C_GRX_N4 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 209 PCIE_GTX_C_MRX_N2 PCIE_MTX_C_GRX_N2 PCIE_GTX_C_MRX_P1 PCIE_MTX_C_GRX_P1 PCIE_GTX_C_MRX_N1 PCIE_MTX_C_GRX_N1 PCIE_GTX_C_MRX_P0 PCIE_MTX_C_GRX_P0 PCIE_GTX_C_MRX_N0 PCIE_MTX_C_GRX_N0 VGA_CRT_R CLK_PCIE_VGA VGA_CRT_G CLK_PCIE_VGA# VGA_CRT_B PLTRST_VGA# VGA_CRT_HSYNC LCD_DATA VGA_CRT_VSYNC LCD_CLK VGA_DDC_CLK VGA_TXCLK- VGA_DDC_DATA VGA_TXCLK+ VGA_TXOUT1- VGA_TXOUT1+ VGA_TXOUT2- VGA_TXOUT2+ VGA_TXOUT3- VGA_TXOUT3+ EC_SMB_CK2 EC_SMB_DA2 VGA_TZCLK- [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 210 Table C-3 VGA/B I/F pin assignments (206-PIN) (4/4) Pin No. Signal name Pin No. Signal Name VGA_TZCLK+ +5VALW VGA_TZOUT1- VGA_TZOUT1+ SUSP# VGA_ENVDD VGA_TZOUT2- VGA_ENBKL VGA_TZOUT2+ VGA_TV_LUMA VGA_TZOUT3- VGA_TV_CRMA VGA_TZOUT3+ [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 211 LCD back light VGA_TXOUT1+ Panel Data Signals DAC_BRIG Inverter Control signal VGA_TXCLK- Panel Clock Signals VGA_LCD_CLK LCD back light VGA_TXCLK+ Panel Clock Signals VGA_LCD_DATA LCD DATA VGA_TZOUT1+ Panel Data Signals VGA_TZOUT1- Panel Data Signals [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 212: Table
Table C-4 LCDS I/F (40-pin)(2/2) VGA_TZOUT2+ Panel Data Signals VGA_TZOUT2- Panel Data Signals VGA_TZOUT0+ Panel Data Signals VGA_TZCLK- Panel Clock Signals VGA_TZOUT0- Panel Data Signals VGA_TZCLK+ Panel Clock Signals [CONFIDENTIAL] C-10 Satellite P200/ P205 Series Maintenance Manual...
Page 213 ADD17 ADD13 ADD18 ADD14 ADD19 ADD20 READY ADD21 ADD16 ADD22 ADD15 ADD23 ADD12 ADD24 ADD7 ADD25 ADD6 VS2# ADD5 RESET ADD4 WAIT# ADD3 INPACK# ADD2 REG# ADD1 BVD2 ADD0 BVD1 DATA0 DATA8 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-11...
Page 214: Table
Table C-7 Microphone I/F pin assignments (6-pin) Pin No. Signal name Pin No. Signal Name MIC-1 +AUD_VREF_J JP15 Table C-8 Head phone Connector pin assignments (6-pin) Pin No. Signal name Pin No. Signal Name INTSPK_L1 INTSPK_R1 NBA_PLUG [CONFIDENTIAL] C-12 Satellite P200/ P205 Series Maintenance Manual...
Page 215 Table C-10 Int. Speaker Connector pin assignments (4-pin) Pin No. Signal name Pin No. Signal Name SPK_L1 SPK_L2 C.11 JP18 Table C11 EC tool Connector pin assignments (4-pin) Pin No. Signal name Pin No. Signal Name +5VALW E51RXD_P80 E51TXD_P80D [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-13...
Page 216 SMBus management channel SMBCLK Reserved RESERVED Reserved RESERVED Output This signal is used for USB-based CPUSB# module detection and power control USBD+ Input/Output USB serial data interface Input/Output USB serial data interface USBD- ground [CONFIDENTIAL] C-14 Satellite P200/ P205 Series Maintenance Manual...
Page 217 Table C-13 Mini Express I/F pin assignments (54-pin) Pin No. Signal name Pin No. Signal Name PCI_WAKE +3VS WLAN_DATA WLAN_CLK +1.5VS MINI_CLKREQ CLK_PCIE# CLK_PCIE XMIT_OFF# PLT_RST# PCIE_RXN2 +3VALW PCIE_RXP2 +1.5VS SMBCLK PCIE_TXN2 SMBDATA PCIE_TXP2 USB_N USB_P +1.5VS +3VS [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-15...
Page 218 Signal Name VCC3.3 VCC3.3 VCC3.3 VCC5 VCC5 VCC5 C.15 JP25 Table C-15 1st HDD I/F pin assignments (22-pin) Pin No. Signal name Pin No. Signal Name VCC3.3 VCC3.3 VCC3.3 VCC5 VCC5 VCC5 [CONFIDENTIAL] C-16 Satellite P200/ P205 Series Maintenance Manual...
Page 219 IDE_DD6 IDE_DD10 IDE_DD5 IDE_DD11 IDE_DD4 IDE_DD12 IDE_DD3 IDE_DD13 IDE_DD2 IDE_DD14 IDE_DD1 IDE_DD15 IDE_DD0 IDE_DDREQ IDE_DIOR# IDE_DIOW# IDE_DIORDY IDE_DDACK# IDE_IRQ IDE_DA1 +5VCD IDE_DA0 IDE_DA2 IDE_DCS1# IDE_DCS3# SHDD_LED# +5VCD +5VS +5VCD +5VS +5VCD SD_CSEL [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-17...
Page 220 Pin No. Signal name Pin No. Signal Name +CAM_VDD USB20_N5 USB20_P5 C.18 JP28 Table C-18 Int. Finger printer I/F pin assignments (5-pin) Pin No. Signal name Pin No. Signal Name +3VS USB20_N5 USB20_P5 [CONFIDENTIAL] C-18 Satellite P200/ P205 Series Maintenance Manual...
Page 221 C.19 JP29 Table C-13 Mini Express I/F pin assignments (54-pin) Pin No. Signal name Pin No. Signal Name +3VS +1.5VS ROB_CLKRE CLK_PCIE# CLK_PCIE PLT_RST# PCIE_RXN2 PCIE_RXP2 +1.5VS PCIE_TXN2 PCIE_TXP2 +1.5VS +3VS [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-19...
Page 222 Signal Name +USB_VCCA USB20_N4 USB20_P4 +USB_VCCA USB20_N2 USB20_P2 C.22 JP34 Table C-22 USB/B I/F pin assignments (5-pin) Pin No. Signal name Pin No. Signal Name +USB_VCCC +USB_VCCC +USB_VCCC USB20_P1 USB20_N1 USB20_P0 USB20_N0 [CONFIDENTIAL] C-20 Satellite P200/ P205 Series Maintenance Manual...
Page 223 KSO14 KSO5 KSO3 KSO4 KSO0 KSO1 KSO2 KSO17 KSO16 +3VS C.24 JP36 Table C-24 Touch Pad I/F pin assignments (5-pin) Pin No. Signal name Pin No. Signal Name TP_CLK TP_DATA +5VS +5VS [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-21...
Page 224 ACZ_SDOUT 3.3V ACZ_SYNC ACZ_SDIN1 REEST ACZ_BITCLK C.27 JP39 Table C-27 CRT/B I/F pin assignments (10-pin) Pin No. Signal name Pin No. Signal Name +5VS +5VS CRT_R_L CRT_G_L CRT_B_L CRT_HSYNC CRT_VSYNC CRT_DDC_DAT CRT_DDC_CLK [CONFIDENTIAL] C-22 Satellite P200/ P205 Series Maintenance Manual...
Page 225 Pin No. Signal name Pin No. Signal Name DC_IN_S2 DC_IN_S2 C.31 PJP2 Table C-31Battery Connector pin assignments (4-pin) Pin No. Signal name Pin No. Signal Name BATT_S1 BATT_S1 ALI/MH# Thermistor TS_A EC_SMDA EC_SMCA [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual C-23...
Page 226 Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Keytop Note Make Break Make Break ‘ ~ 7 & BkSp [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 227 Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 228 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Keytop Note Make Break Make Break Ctrl(L) Alt (L) Space ALT (R) Ctrl(R) ← Home ↑ ↓ PgUp PgDn → [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 229 5. * This key corresponds to key No. 42 in a 102-key model. 6. * Refer to Table D-6, No. 124 key scan code. 7. * Refer to Table D-7, No. 126 key scan code. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 230 Shift key, scan codes are changed as listed below: With left Shift With right Shift Set 1 E0 AA ___________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12_________ E0 F0 59 E0 12____________ E0 59 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 231 AA E0 12 E0 2F E0 F0 2F E0 F0 12 Table D-4 Scan codes with Fn key Code set 1 Code set 2 Keytop Make Break Make Break L-CTRL L-ALT ARROW NUMERIC Scrl [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 232 Code set 2 Keytop Make Break Make Break (–) Table D-6 No.124 key scan code Code set 1 Code set 2 Shift Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 233 Table D-7 No.126 key scan code Key top Shift Code set 1 Code set 2 Make Make Pause Common Ctrl *: This key generates only make codes. [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 234 United Status (US) Keyboard 2. Traditional Chinese (CH) Keyboard...
Page 235 3. Thai (TI) Keyboard 4. Korean (KO) Keyboard...
Page 236 5. United Kingdom (UK) Keyboard 6. US International (UI) Keyboard...
Page 237 7. Hebrew (HB) Keyboard 8. Danish (DM) Keyboard...
Page 238 9. Swiss (SW) Keyboard 10. Arabic (ARE) Keyboard...
Page 239 11. Czech (CZ) Keyboard 12. Russian (RU) Keyboard...
Page 240 13. Portuguese (PO) Keyboard 14. Slovakian (SL) Keyboard...
Page 241 15. Italian (IT) Keyboard 16. French (FR) Keyboard...
Page 242 17. German (GR) Keyboard 18. Greek (GK) Keyboard...
Page 243 19. Hungarian (HG) Keyboard 20. Spanish (SP) Keyboard...
Page 244 21. Turkish (TR) Keyboard 22.Turkish F (TR-F) Keyboard...
Page 245 23.Swedish (SD) Keyboard 24.Belgian (BE) Keyboard...
Page 246 25.Yugoslavian (YU) Keyboard 26.Norwegian (NW) Keyboard...
Page 247 27.Scandinavian (ND) Keyboard 28.Canadian Multinational (AC) Keyboard...
Page 248 29.Canadian Bilingual (CB) Keyboard 30. Japanese (JP) Keyboard...
Page 249: Appendix F Series Screw Torque List
USB/B to Lower Function PCB to Strip coer LOGIC ASSY K/B to Upper MA0000069G0 M2.0*4 1.5~2.0Kgf.cm LVDS to Upper MMCK20060G0 M2*6 1.5~2.0Kgf.cm CRT Board to Lower MA000005WG0 M2.5*3 2.0~2.5Kgf.cm Lower(HDD housing) to Upper [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 250 MACA00300G0 M2.5*20 2.5~3.0Kgf.cm Upper (KB support) to Lower MAFA94001N0 4.75*9.6+SW 2.5~3.0Kgf.cm Lower to D-sub conn HDD ASSY 2.5~3.0Kgf.cm MAAA03032G0 M3*3 HDD BRK L/R to HDD ODD ASSY 1.5~2.0Kgf.cm MACK20251G0 M2*2.5 ODD BRK to ODD [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...
Page 251: Appendix G Reliability
Appendix G Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table G-1 MTBF Component Time (hours) 10,000 Keyboard 60,000 300,000 Optical (DVD/CD) drive 60,000 AC adaptor 60,000 [CONFIDENTIAL] Satellite P200/ P205 Series Maintenance Manual...

This manual is also suitable for:

Satellite p205

Toshiba Satellite P200 Maintenance Manual

Table of Contents

Chapter 1 Hardware Overview

Table of Contents

Chapter 2 Troubleshooting Procedures

Table of Contents

Chapter 3 Tests and Diagnostics

Chapter 4 Replacement Procedures

Table of Contents

Appendix A Handling the LCD Module

Appendix B Board Layout

Appendix C Pin Assignments

Appendix F Series Screw Torque List

Appendix G Reliability

Quick Links

Chapters

Troubleshooting

Related Manuals for Toshiba Satellite P200

Summary of Contents for Toshiba Satellite P200

This manual is also suitable for:

Table of Contents