Page 2
KRC-666/G/R DISASSEMBLY FOR REPAIR 3 7 63 1515 0 How to remove the Volume Knob How to install the Volume Knob 1. Remove the rear cover of panel unit. 1. Remove the peeling paper of LIGHTING BOARD BOSS 2. Juck up as remove the switch unit (x16-) and Volume Knob side.
Page 3
3 7 6 3 1 5 1 5 0 MODE K,M-TYPE E-TYPE TAPE 1800mV 1800mV 1800mV 1372mV MP IN 600mV 855mV E-VOL TUNER 3600mV 3600mV LEVEL & AM+B SW5V PRE MUTE PRE OUT TAPE SW5V AUDIO OUT QUAL BUFFER DECODER BUFFER S-METER MUTE...
Page 4
KRC-666/G/R COMPONENTS DESCRIPTION 3 7 63 1515 0 SWITCH UNIT (X16-2030-21) Ref. No Purpose Function Operation/Condition/Compatibility ¡ LCD driver Drives LCD Remote control IC Controls the unit Q1,Q4 REMO ON switch The power supply of IC2 is turned on when base level goes "L"...
Page 5
KRC-666/G/R MICROCOMPUTER'S TERMINAL DESCRIPTION 3 7 63 1515 0 SYSTEM MICROCOMPUTER MN101C49HNA (IC1: X14-) Pin No. Name Module Description Processing Operation VREF- Power supply GND for A/D F REEL TAPE Reel pulse FWD Cassette mecha reel pulse output FWD Vth=2.5V...
Page 6
KRC-666/G/R MICROCOMPUTER'S TERMINAL DESCRIPTION 3 7 63 1515 0 Pin No. Name Module Description Processing Operation PLL CLK TUNER I/O Tuner I2C SCL PANEL 5V to PANEL I/O Panel 5V ON/OFF Attached the panel, ACC ON :L (Refer to "Truth table 5")
Page 7
KRC-666/G/R MICROCOMPUTER'S TERMINAL DESCRIPTION 3 7 63 1515 0 Pin No. Name Module Description Processing Operation FWD input :L TAPE O Tape EQ input switching REV input :H MODE except TAPE :keep the value NORMAL :H, METAL :L METAL TAPE...
Page 8
KRC-666/G/R TEST MODE 3 7 63 1515 0 1. How to enter the test mode 7. Test mode specifications of the cassette receiver • While holding the Preset 1 and Preset 3 keys, reset the unit. • BLANK SKIPP :OFF 2.
KRC-666/G/R TEST MODE 3 7 63 1515 0 11. Special display when the display is All ON Security Pressing the Preset keys while the power is All OFF • Forced Power ON mode (All models) displays the following information. Even when the security is approved, resetting the unit...
Page 10
KRC-666/G/R ADJUSTMENT 3 7 63 1515 0 Set the controls and switches as follows. BALANCE :center position BASS :center position LOUD :OFF DOLBY NR :OFF FADER :center position TREBLE :center position TUNER OUTPUT ALIGNMENT ITEM INPUT SETTINGS (RECEIVER) ALIGN FOR FIG.
Page 11
KRC-666/G/R 3 7 63 1515 0 DTC143TUA PRE OUT ∗ UN5114 REAR FRONT (X14-9180-2x) UN5211 UN5216 C356 C357 ANT. 0.01 0.01 2SA1036K 52mH ∗ 2SA1576A R355 R356 R361 R362 RF GND Q351 Q352 Q355 Q356 FM ANT AM ANT OSC GND...
Page 12
KRC-666/G/R 3 7 63 1515 0 DC-IN SP OUT F1 10A FUSE POWER ANTENN DETECT R252 R254 1.5K C258 3300u16 D270 ∗ TEL MUTE 1u50 C256 C255 22u16 D269 0.01 0.47u50 R255 ∗ R33 47K ACC DETECTION POWER 4.7K 5.0V...
Page 14
KRC-666/G/R 3 7 63 1515 0 SWICTH UNIT (X16-2030-21) TP18 TP19 TP20 TP21 TP22 TP23 TP24 TP25 TP26 ESD-GND 0.01 TP13 TP27 FLIP DET AUTO RESET RESET VOL A ILL-GND 0.01 0.01 VOL B 1Kx4 ILL+B 1Kx4 TP11 R6 1K...
Page 15
3 7 63 1515 0 ED1(SEGMENT) ED1(COMMON) L 13942296513 KRC-666/R/G (2/2) u163 CAUTION : For continued safety, replace safety critical components only with manufacturer's recommended parts (refer to parts list). Indicates safety critical components. To reduce the risk of electric shock, leakage-current or resistance measurements shall be carried out (exposed parts are acceptably insulated from the supply circuit) before the appliance is returned to the customer.
Page 16
KRC-666/G/R PC BOARD 3 7 63 1515 0 (COMPONENT SIDE VIEW) (FOIL SIDE VIEW) X16-2030-21 (J74-1452-02) X16-2030-21 (J74-1452-02) FLIP DET VOL B VOL A REMO ILL +B ILL GND D GND L 13942296513 X16-2030-21 Ref. No address X89-2570-11 (J74-1450-02) X89-2570-11 (J74-1450-02)
Page 17
KRC-666/G/R 3 7 63 1515 0 PC BOARD (COMPONENT SIDE VIEW) L 13942296513 u163 X14-9180-2x Ref. No address Refer to the schematic diagram for the values of resistors and capacitors.
Page 25
KRC-666/G/R PARTS LIST 3 7 63 1515 0 CAPACITORS 2 2 0 • Capacitor value CC45 Color* 010 = 1pF 0 = 22pF 1 = Type ... ceramic, electrolytic, etc. 4 = Voltage rating 100 = 10pF 2 = Shape ... round, square, etc.
Page 26
Weight 1.20kg 1.20kg KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice. Manufactured under license from Dolby Laboratories."Dolby" and the double-D symbol are trademarks of Dolby Laboratories. KENWOOD CORPORATION 2967-3, Ishikawa-machi, Hachioji-shi, Tokyo 192-8525, Japan KENWOOD ELECTRONICS ITALIA S.p.A.