Page 1
INSTRUCTION MANUAL VCB-3100P BEDIENUNGSANLEITUNG VCB-3170P MANUEL D’INSTRUCTIONS Í [ B/W CCD Camera CCD-Schwarzweißkamera Caméra CCD Noir et Blanc C CD ½ ú T About this manual Über diese Bedienungsanleitung • Before installing and using the camera, please • Lesen Sie bitte vor der Montage und dem read this manual carefully.
TROUBLESHOOTING........12 • High sensitivity, minimum required illumination of 0,1 lux with F1.2 lens SPECIFICATIONS ..........13 • Horizontal resolution – Model VCB-3100P more than 400 TV lines ACCESSORIES – Model VCB-3170P more than 560 TV lines C mount adaptor (5 mm) ....1 pc.
Disconnect or where it could be subject to direct the power cord immediately, and consult sunlight, as that could cause deformation, your dealer (or a Sanyo Authorized Service discoloration or other damages. Centre). Be careful when installing close to the...
PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. AC power cord External sync composite video signal input connector (VS IN: BNC type) Connect to this connector the synchronizing signal output...
Page 5
(see page 8 "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Control name VCB-3170P VCB-3100P Internal/Line lock switch [VCB-3170P] (SYNC) Auto gain control switch (AGC)
PARTS NAMES Flange-back adjustment screw (FLANGE BACK ADJ.) Flange-back lock screw (FLANGE BACK LOCK) Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold ADJ.
Page 7
Installation of a VIDEO type auto-iris lens (sold separately) 2 (A) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. Remove the lens mount cap. Attach the supplied C mount adaptor (A) to the auto-iris lens (B), then install the assembly on the camera.
MOUNTING THE LENS If using Sanyo (DC type) auto-iris lens • VCL-CS8LY: Standard angle, f= 8 mm • VCL-CS4LY: Wide angle, f= 4 mm • VCL-CS2LY: Ultra-wide angle, f= 2.8 mm If using a VIDEO type auto-iris lens • Set the ALC and LEVEL controls on the lens to adjust the iris.
SETTINGS [VCB-3100P] [VCB-3170P] VR301 VR301 E. S. E. S. SYNC VIDEO VIDEO A. I. A. I. VR302 LENS LENS Line phase adjustment When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched.
Page 10
(model VCB-3170P) or the EI and BLC switches (model 1/10000 sec. VCB-3100P) must be set to the OFF position. • Using the high speed electronic shutter indoors with low lighting, will give darker pictures. In such a case, add some lights to make sure the lighting is sufficient.
Page 11
Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/BLC switch (model VCB-3170P) to EI (electronic iris)-ON or the EI switch (model VCB-3100P)) to the ON position. The dynamic range of the electronic iris will be as indicated in table...
Page 12
(backlight compensation)-ON position, to engage the backlight compensation function. Use an auto-iris lens. Set the EI/BLC switch (model VCB-3170P) to BLC-ON or the BLC switch (model VCB-3100P) to the ON position. If using a VIDEO type auto-iris lens (VCB-3100P) • The ALC volume on the lens should be turned all the way to Av (Average).
TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen •...