TA-VE800G 3 7 63 1515 0 SERVICE MANUAL AEP Model UK Model SPECIFICATIONS L 13942296513 u163 INTEGRATED AV AMPLIFIER MICROFILM — 1 — http://www.xiaoyu163.com...
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN u163 THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. — 2 — http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 1 3 7 63 1515 0 SERVICE NOTE Adjustment of OSD Screen Position ALL CLEAR The position of the screen can be adjusted freely to correct the devia- Mode which erases all the user memories registered in this unit and tion of the OSD screen caused by the monitor type that users are sets to setting at shipment.
http://www.xiaoyu163.com SECTION 2 This section is extracted from 3 7 63 1515 0 instruction manual. GENERAL L 13942296513 u163 — 4 — http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 4 3 7 63 1515 0 ELECTRICAL ADJUSTMENT Video Frequency Adjustment Connection: frequency counter OSD board JW10 (FS CHECK) Method: 1. Press the POWER button without connecting anything to the ex- ternal input terminal (VIDEO IN etc.). 2. Adjust CT202 of the OSD board so that the reading on the fre- quency counter becomes 17.734475 MHz ±...
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 Adjustment Location: [S. VIDEO BOARD] TM201 !ª (VIDEO) OSD width !• (GROUND) L 13942296513 [OSD BOARD] J210 J209 OSD width CT202 JW10 CT201 Video frequency u163 — 24 — http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3 7 63 1515 0 5-11. IC PIN FUNCTION • IC107 DISPLAY CONTROL (MB90673PF-G-166-BND) Pin No. Pin Name Function Video selector control output Video selector control output Key input Key input Key input Key input Not used Not used Not used IFDATAIN Not used...
Page 38
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function MODE0 Mode select terminal (Fixed at “H”) MODE1 Mode select terminal (Fixed at “H”) MODE2 Mode select terminal (Fixed at “L”) STANDBY Standby terminal (+5V) STOP Request input of reset interrupt V-INH Video inhibit output (Not used) RDSDATA...
http://www.xiaoyu163.com 3 7 63 1515 0 • IC205 OSD (MB90095PF-G-161-BND) Pin No. Pin Name Function Luminous signal input for superimpose displays (Not used) Chroma signal input for superimpose displays (Not used) Composite signal input for superimpose displays AVcc – Power supply (+5V) (Analog) FSCO Color burst phase signal output VBLK...
http://www.xiaoyu163.com 3 7 63 1515 0 • IC209 OSD CONTROLLER (MB90672PF-G-125-BND) Pin No. Pin Name Function 1, 2 AD14, AD15 Address bus and data bus input/output 3 to 6 A16 to A19 Address bus input/output Chip Enable output to RC controller (For communication using personal computers) PCLK Clock output to RC controller (For communication using personal computers) PDATA OUT...
Page 41
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function MODE0 Mode setting (Fixed at “H”) MODE1 Mode setting (Fixed at “L”) MODE2 Mode setting (Fixed at “L”) HSTX – Hardware standby (Fixed at “H”) STOP Request input of reset interrupt IR-IN (A6) IR sensor remote control input —...
http://www.xiaoyu163.com 3 7 63 1515 0 6-2. BACK PANEL SECTION CNP901 CNJ901 F803, F804 F801, F802 T901 L 13942296513 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number speci- fied.
http://www.xiaoyu163.com 3 7 63 1515 0 6-3. CHASSIS SECTION IC671 IC601 Q704 Q603 F901 Q753 F902 Q703 Q604 #1 Q754 not supplied not supplied not supplied L 13942296513 not supplied The components identified by mark ! or dotted line with mark ! are critical for safety.
http://www.xiaoyu163.com SECTION 7 3 7 63 1515 0 ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in the parts list • SEMICONDUCTORS The components identified by mark ! In each case, u: µ , for example: may be different from the parts specified in the dia- or dotted line with mark ! are critical uA...: µ...