Page 1 Toshiba Personal Computer TECRA S1 Maintenance Manual TOSHIBA CORPORATION S/ No. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 2 The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the TECRA S1 at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice.
Page 3: General
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer TECRA S1, referred to as TECRA S1 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
Page 4: Handling The Lcd Module
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the TECRA S1 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.
Page 5 Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the XXXXX that appears on its display is presented in the type face below: Format complete System transferred TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 6: Table Of Contents
Keyboard ......................2-25 Display ......................... 2-27 DVD-ROM Drive....................2-29 CD-ROM Drive....................2-31 2.10 LAN........................2-33 2.11 Cooling Module....................2-34 Chapter 3 Diagnostic Programs General ........................3-1 Quick Start......................3-3 Option........................3-9 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 7 System Test ......................3-22 Memory Test ......................3-29 Storage........................3-34 Video ........................3-39 Communication (COMM)..................3-47 3.10 Peripherl ....................... 3-54 3.11 Audio ........................3-58 3.12 Mode Error Codes and description............... 3-59 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 8 Top Cover with the Display Assembly ..............4-46 4.13 I/O Board......................4-50 4.14 System Board ....................... 4-51 4.15 Display Mask......................4-53 4.16 Inverter Board ...................... 4-55 4.17 LCD Module ......................4-57 viii TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 9 Pin Assignments.................... C-1 Appendix D Keyboard Scan/Character Codes ..............D-1 Appendix E Key Layout.....................E-1 Appendix F Wiring Diagrams.................... F-1 Appendix G BIOS Rewrite Procedures ................G-1 Appendix H EC/KBC Rewrite Procedures................ H-1 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 10 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 11: Hardware Overview
Chapter 1 Hardware Overview Downloaded from www.Manualslib.com manuals search engine...
Page 12 1 Hardware Overview 1-ii TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 13 CD-R/RW Drive ...................... 1-15 CD-RW/DVD-ROM Drive ..................1-16 Power Supply ......................1-17 Batteries ........................1-18 1.9.1 Main Battery..................1-18 1.9.2 Battery Charging Control ..............1-18 1.9.3 RTC Battery ..................1-19 TECRA S1 Maintenance Manual 1-iii Downloaded from www.Manualslib.com manuals search engine...
Page 14 Table 1-4 CD-R/RW drive specifications................1-15 Table 1-5 CD-RW/DVD-ROM drive specifications ............1-16 Table 1-6 Battery specifications ..................1-18 Table 1-7 Quick/normal charging time................1-18 Table 1-8 RTC battery charging/data preservation time ............ 1-19 1-iv TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 15: Features
1 Hardware Overview Features The Toshiba TECRA S1 is a lightweight notebook PC based on the Mobile Banias processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be battery-operated for a longer period of time. The display uses a 14.1-inch XGA or 15-inch XGA/UXGA (BTOable) LCD panel, capable of...
Page 16 The keyboard has 85 keys conforming to the US key layout. The keyboard has 85 keys confirming to the UK key layout. Batteries The computer has a removable Lithium Ion battery pack and an internal RTC battery. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 17 16-bit Multiple Function PC Cards and CardBus cards. It also supports booting from a PC Card HDD. Toshiba Dual Pointing Device Toshiba Dual Pointing Device has 2 kinds of input devices. One is AccuPoint, another one is TouchPad. Fast Serial InfraRed (FIR) communications port An IrDA 1.1 compatible FIR port is provided, enabling wireless communication at a...
Page 18 The RJ11 modem jack is used to accommodate a telephone line. Bluetooth The bluetooth is option integrated device. It uses RF transmission in 2.4 GHz band. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 19: Features
Ext. Speaker AC Adapter LCD/FL Inverter Docking Int MIC System Board Conn Bluetooth Conn. Serial Keyboard Parallel Battery PS/2 Mouse Selectable Main /Keyboard Battery Wireless Figure 1-2 System unit configuration TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 20: System Unit Components
2nd BATTERY Internal LPC DR/RCV Serial (MAX3243) (1/2) EC/KBC Flash (2/2) Super I/O (LPC 47N253) (LPC47N253) Parallel Touch PS/2 Main Battery E2PROM PS/2 PS/2 Figure 1-3 System unit block diagram TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 21 − 256 MB (16M x 16 x 8P) − 512 MB (16M x 16 x 16P) − 512 MB (32M x 16 x 8P) • 2.5 volt operation • No parity bit • 64-bit data transfer TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 22 − SMBus interface − Super I/O interface − Power management control − Suspend/resume control − ACPI support PC Card controller • CB720 − CardBus/PC Card controller − SD Card controller TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 23 − Scan controller function − Interface controller function − Controlling the switching between the AccuPoint and external PS/2 mouse or between the built-in keyboard and external PS/2 keyboard or their simultaneous operation TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 24 − Communication codes supported: For data communication: V.90 (56K bps) data communication control V.32 bis (14.4K, 12K, 9600) V.22 bis (2400, 1200) V.22 (1200) V.23 (1200, 600, 75) V.21 (300) 1-10 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 25 • 2.4 GHz DSSS wireless LAN card plugged in the internal Mini PCI Card slot Super I/O • LPC 47N253 − Serial port control − Parallel port control − Infrared communications control TECRA S1 Maintenance Manual 1-11 Downloaded from www.Manualslib.com manuals search engine...
Page 26: Inch Hdd
Toshiba Item MK6022 IC25N040 MK4019 MK3021 ATCS05 Formatted 60.0116GB 40.0007GB 40.0007GB 30.0058GB capacity (GB) User data 117,210,24 78,140,160 78,140,160 58,605,120 sectors Bytes/sector Rotational 5400rpm 5400rpm 5400rpm 4200rpm speed (RPM) 1-12 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 27: Dvd-Rom Drive
Data buffer size (Kbytes) Formats supported DVD-ROM, DVD-R (Read) CD-DA, CD+(E)G, CD-MIDI, CD-TEXT CD-ROM, CD-ROM XA, CD-I CD-I Bridge (Photo-CD, Video-CD) Multisession CD (Photo-CD, CD-EXTRA, CD-R, CD-RW) CD-R (Read), CD-RW (Read) TECRA S1 Maintenance Manual 1-13 Downloaded from www.Manualslib.com manuals search engine...
Page 28: Cd-Rom Drive
Rotational speed (RPM) 5,136 Data buffer size (Kbytes) Formats supported CD-DA, CD-ROM, CD-R, CD-ROM XA, CD-I FMV, Photo CD (Multisession) , VIDEO CD, CD Extra (CD Plus), CD-G, CD-RW 1-14 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 29: Cd-R/Rw Drive
CD-ROM, CD-R (max 24) CD-RW (max 24) Write: CD-R (max 8) CD-RW (max 8) Cache (Mbytes) Formats supported Video CD, Photo CD, CD-ROM, CD-ROM XA, CD-EXTRA, CD-R, CD-Rewritable, CD-DA, CD-Text TECRA S1 Maintenance Manual 1-15 Downloaded from www.Manualslib.com manuals search engine...
Page 30: Cd-Rw/Dvd-Rom Drive
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, (Photo-CD, Video- CD-ROM, CD-ROM XA, MIXED MODE CD), Multisession CD, CD-I, CD-I Bridge (Photo-CD, CD (Photo-CD, Video-CD), Multisession CD (Photo-CD, CD-EXTRA, CD-EXTRA, Portfolio, CD-R, CD-RW), Portfolio) CD-R, CD-RW 1-16 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 31: Power Supply
• Monitors the voltage output to the system block (load/logic circuit side). • Monitors the voltage, overvoltage, input/output current of the battery pack. • Monitors the internal temperature of the battery pack. • Monitors the supply voltage from the AC adapter. TECRA S1 Maintenance Manual 1-17 Downloaded from www.Manualslib.com...
Page 32: Batteries
Table 1-7 Quick/normal charging time Charge time Off-state charge About 3 hours On-state charge About 4 - 9 hours 1-18 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 33: Rtc Battery
Table 1-8 lists the charging time and data preservation period of the RTC battery. Table 1-8 RTC battery charging/data preservation time Status Time Charging AC Adapter or main battery pack used 50 hours time (power on) TECRA S1 Maintenance Manual 1-19 Downloaded from www.Manualslib.com manuals search engine...
Page 34 2 Troubleshooting Chapter 2 Troubleshooting TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 35 Procedure 3 Connector Check and Replacement Check......... 2-25 DVD-ROM Drive ....................2-27 Procedure 1 DVD-ROM Cleaning Check............2-27 Procedure 2 Test Program Check ..............2-27 Procedure 3 Connector Check and Replacement Check......... 2-27 2-ii TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 36 Procedure 1 Test Program Check ..............2-31 Procedure 2 Connector Check and Replacement Check......... 2-31 2.11 Cooling Module ....................... 2-32 Procedure 1 Test Program Check ..............2-32 Procedure 2 Connector Check and Replacement Check......... 2-32 TECRA S1 Maintenance Manual 2-iii Downloaded from www.Manualslib.com manuals search engine...
Page 37 Table 2-1 Printer port LED boot mode status (1/3)............2-14 Table 2-2 Printer port LED resume mode status (1/7) ..........2-17 Table 2-3 HDD error code and status................2-21 2-iv TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 38: Outline
13. Multimedia sound system with line-in and line-out ports 14. Headphone 15. Microphone 16. External FDD attachment 17. A-BEX TEST CD-ROM TCDR-702 18. Music CD 19. DVD-ROM TSD-1 (TOSHIBA EMI DVD Test Media) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 39: Basic Flowchart
When booted, the computer overrides password protection and automatically erases the current password. Make sure the Toshiba version of Windows® 98SE, 2000, or XP has been installed on the HDD. Any other operating system can cause the computer to malfunction.
Page 40 Tomorrow Toshiba" displayed See the previous page to "Password=" displayed ?? delete the password. Follow the HDD diagnostic OS started ?? Procedure in Section 2.6 Figure 2-1 Basic flowchart (1/2) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 41 Identify the test resulting in the Any error detected by the error and perform the appropriate diagnostic program ?? diagnostic procedures The system is normal. Figure 2-1 Basic flowchart (2/2) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 42 7. If an error is detected by the LAN test, follow the LAN troubleshooting procedures in section 2.12. 8. If an error is detected by the Fan On/Off test, follow the cooling module troubleshooting procedures in Section 2.13. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 43: Power Supply
On in orange Battery being charged On in green Battery fully charged, with AC adapter connected Blinking in orange Battery low *1 while driving the computer (at equal intervals) Else TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 44 Make sure the DC IN LED goes on in green. If it does not, go to Procedure 2. Check 2 Make sure the Battery LED goes on in orange or green. If it does not, go to Procedure 3. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 45: Procedure 2 Connection Check
Make sure the battery pack has been correctly installed in the computer. If the battery LED does not go on while the battery pack has been installed correctly, go to Procedure 3. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 46: Procedure 3 Replacement Check
Check 2 Replace the system board with a new one. If the battery pack is still not working properly, perform Check 3. Check 3 Replace the CPU with a new one. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 47: System Board
Procedure 1 Message Check Procedure 2 Printer Port LED Check (in Boot Mode) Procedure 3 Printer Port LED Check (in Resume Mode) Procedure 4 Test Program Check Procedure 5 Replacement Check 2-10 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 48 If an error message appears on the display, perform Check 1. If there is no error message, go to Procedure 2. If there is no error beep code tone out, go to Procedure 3 If Toshiba MS-DOS or Toshiba Windows 95/98/NT/2000 is loaded normally, go to Procedure 5. Check 1 If the following error message is displayed on the screen, press the F1 key as prompted.
Page 49 Figure 2-2 Printer port LED Figure 2-3 illustrates how the printer port LED shows a status value. Printer port LED status = 35H Figure 2-3 Printer port LED board 2-12 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 50 NOTE: The printer port LED displays each status upon completion of the corresponding POST test item. If the POST terminates with 21h displayed on the printer port LED, for example, the POST has completed KBC initialization and detected an error TECRA S1 Maintenance Manual 2-13 Downloaded from www.Manualslib.com...
Page 51 Initialize Video (6845 Regs),set display mode 1D H DEBUG_VIDEO_COLOR_INIT Initialize Color Adapter,and setup display reg. DEBUG_VIDEO_BW_INIT Initialize Monochrome Adapter,and setup display reg. DEBUG_HWIO_TEST_DMA_PAG Send out some value,to test 8237A Page Registers 2-14 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 52 3D H DEBUG_MOUSE_INIT Clear keyboard buffer for search and Init the Mouse DEBUG_KEYB_SET_LEDS_1 Send keyboard command to Update keyboard NUMLOCK status DEBUG_OEM_DEVICE_CONFIG special init of COMM and LPT ports TECRA S1 Maintenance Manual 2-15 Downloaded from www.Manualslib.com manuals search engine...
Page 53 Into Int19, to boot from floppy or other boot device DEBUG_ACPI_INIT Initialize the ACPI function DEBUG_PM_CPU_INIT Power manager initial & GEYSERVILLE CPU initialize DEBUG_USB_HC_INIT Clear USB status register and Initiallize the USB Hub controllor 2-16 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 54: Procedure 3 Printer Port Led Check (In Resume Mode)
Proceed with Crisis Boot,first initial superio and boot device DIAG_FATAL_ERROR Fatal Error,like the RAM error or ROM error C C H DIAG_CRISIS_BEGIN Start process the Crisis recovery procedure DIAG_RESUME_RAM_ERROR Resume SMRAM not Found TECRA S1 Maintenance Manual 2-17 Downloaded from www.Manualslib.com manuals search engine...
Page 55: Procedure 4 Test Program Check
The system board, memory, or CPU may be defective. Disassemble the computer following the steps described in Chapter 4 and replace the system board, memory module or CPU with a new one. 2-18 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 56: Inch Hdd
If the problem persists, go to Procedure 2. Procedure 2 Partition Check Enter the Toshiba MS-DOS system. Perform the following checks: Check 1 Type C: and press the Enter key. If you cannot change to drive C, perform Check 2.
Page 57: Procedure 3 Format Check
Abort, Retry, Fail? Check 5 Use the SYS command in the Toshiba MS-DOS system to install system files. If the following message appears on the display, the system files have been transferred to the HDD. Restart the computer. If the problem persists, go to Procedure 3.
Page 58: Procedure 4 Test Program Check
Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed disk dos not support SMART disk read attribute threshold error disk read attribute value error disk SMART attribute value error TECRA S1 Maintenance Manual 2-21 Downloaded from www.Manualslib.com manuals search engine...
Page 59: Procedure 5 Connector Check And Replacement Check
Chapter 4. If the problem persists, perform Check 4. Check 4 The CPU may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. 2-22 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 60: Keyboard
Check 2. Check 2 The keyboard may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3. TECRA S1 Maintenance Manual 2-23 Downloaded from www.Manualslib.com...
Page 61 Chapter 4. If the problem persist, perform Check 5. Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-24 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 62: Display
3. If there is still an error, perform Check 2. Check 2 The LCD/FL cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 3. TECRA S1 Maintenance Manual 2-25 Downloaded from www.Manualslib.com...
Page 63 Check 10 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 10. 2-26 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 64: Dvd-Rom Drive
Insert the diagnostics CD in the computer's CD-ROM, turn on the computer and run the test. Then insert a test DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the DVD-ROM drive. See Chapter 3 for information on how to perform the test.
Page 65 Check 6 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3. 2-28 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 66: Cd-Rom Drive
Check 2 The connector may be faulty. Replace the connector with a new one following the steps in Chapter 4. If the CD-ROM drive is still not functioning properly, perform Check 3. TECRA S1 Maintenance Manual 2-29 Downloaded from www.Manualslib.com...
Page 67: Cd-Rom Drive
Chapter 4. If the problem persist, perform Check 6. Check 6 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. 2-30 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 68: Lan
Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. TECRA S1 Maintenance Manual 2-31 Downloaded from www.Manualslib.com manuals search engine...
Page 69: Cooling Module
Chapter 4. If the problem persist, perform Check 5. Check 4 The CPU may be faulty. Replace it with a new one following the steps in Chapter 4. 2-32 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 70 2.14 Cooling Module 2 Troubleshooting Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one. TECRA S1 Maintenance Manual 2-33 Downloaded from www.Manualslib.com manuals search engine...
Page 71: Diagnostic Programs
Chapter 3 Diagnostic Programs Downloaded from www.Manualslib.com manuals search engine...
Page 72 3 Diagnostic Programs Chapter 3 Contents General.......................... 1 Quick Start ........................3 3.2.1 Quick Test ....................3 3.2.2 Customization Test.................. 3 3.2.3 Audio Play Test ..................7 3.2.4 Audio Record Test................... 7 3.2.5 DMI Read ....................7 3.2.6 DMI Write ....................7 3.2.7 System Information .................
Page 73 3 Diagnostic Programs 3.12 Quick Test Item List ...................... i TECRA S1Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 74 Downloaded from www.Manualslib.com manuals search engine...
Page 75: General
A LPT Loop back Connector (for LPT port Loop back test) A standard LPT printer (for LPT Printer test) A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test) A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) An External Monitor (for DISPLAY test) TECRA S1Maintenance Manual Downloaded from www.Manualslib.com...
Page 76 3 Diagnostic Programs 3.1 General A Serial Port Loop back Connector (for serial port test) A CD-ROM Driver (for CD-ROM test) A Microphone An Audio CD (for CD-ROM audio play test) A Data CD (for CD-ROM test) A Test Media CDRW/DVD-CDRW Drive A Rewriteble CDRW (Direct CD Format) The following chapters describe all the test details.
Page 77: Quick Start
3.2 Quick Start 3 Diagnostic Programs Quick Start Boot from Service Diagnostic CD, the following screen will be displayed: Please select a test item or select 9 to exit to MS-DOS: 3.2.1 Quick Test When this item selected, system will run the configured test items and generate a test report automatically.
Page 78 3 Diagnostic Programs 3.2 Quick Start Select ‘Test Mouse’ or press F8 to run the test. The test information would prompt in the screen as below. This test item need user to verify whether the mouse works normally. The test result will be displayed in the following screen: TECRA S1Maintenance Manual Downloaded from www.Manualslib.com...
Page 79 3.2 Quick Start 3 Diagnostic Programs Here is another method to run the test: Highlight a test item by using arrow keys, then press Enter to start. If there are parameters provided, user should set parameters in the parameter dialog window. CPU Speed Test (Step by Step): Select test item: Select System—CPU—CPU Speed, then press the Enter key.
Page 80 3 Diagnostic Programs 3.2 Quick Start Test Result System will automatically run and display the test result as follows: Following is the comparison report of the two testing methods mentioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the parameters artificially, (See 3.3.3 Item’s Parameters Configuration) Then press F8 to start test.
Page 81: Audio Play Test
3.2 Quick Start 3 Diagnostic Programs 3.2.3 Audio Play Test Check whether the system could playback audio normally. When the test complete, a file named Audio_P.log will be saved in the defined location 3.2.4 Audio Record Test Check whether the system could record the sound and playback it normally. When the test complete, a file named Audio_R.log will be saved in the defined location 3.2.5 DMI Read Read the information from the system’s SMBIOS and display it in the screen as follows:...
Page 82: Quick Start
3 Diagnostic Programs 3.2 Quick Start In this screen, there are two lines which attribute could be edited and updated. The 1 line (the font in yellow with blue background) shows the attribute’s value that is read from the current system and the 2 line (the font in red with turquoise background) shows the same value as that in the 1 line before user’s editing.
Page 83: System Information
3.2 Quick Start 3 Diagnostic Programs 3.2.7 System Information This function is used to read the system information. When the test complete, a file named System.log will be saved in the defined location During the reading process, the following screen will be displayed to indicate that the progress is in detection: On the left column of the above screen, the detected hardware components are listed.
Page 84: View Logs
3 Diagnostic Programs 3.2 Quick Start User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current program. On the left column, the components information is listed and user can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component.
Page 85 3.2 Quick Start 3 Diagnostic Programs 1. Diagnostics Windows When a test item is running, a Diagnostics Windows is displayed in full screen. It consists of the following parts: Title Bar, Test Running Status and Report Panel, Status Bar. There would prompt a message box called USER BREAK in the central of the window whether user press ESC to interrupt the test.
Page 86 3 Diagnostic Programs 3.2 Quick Start Program Name and Its Version: Service Diagnostic Ver1.00; Test Module Name: Label the name and version of the test module. For example, in the above screen, the name of the test module is ‘Memory Tester Build Date 2002.12.31’. Status Bar: Located at the bottom of the screen as follows: The status bar is used to indicate the current script setting and test status.
Page 87 3.2 Quick Start 3 Diagnostic Programs Interactive: Display INTER when ‘Interactive’ is enabled; Manual Interrupt Method: Display ‘Esc: Break’ to tell the user how to manually interrupt the test process. TECRA S1Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 88: Options
3 Diagnostic Programs 3.3 Option Options 3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s parameters and those parameters created by the LOG file. Options Menu Notes: Select All/None Items • Switch between selecting all test items and selecting none, the hot key is F6. Test Selected Items •...
Page 89: Batch Parameters Configuration
3.3 Option 3 Diagnostic Programs Configure batch parameters and all the test item’s parameters. Load Batch Parameters • Upload all the test items and parameters in the *.ini file Save Batch Parameters • Save all parameters and test items configured in the editor to a specified file Log Parameters •...
Page 90 3 Diagnostic Programs 3.3 Option Test Order • Specify the order of the test items. Choose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence. Test Options • Choose one of the following options: Wait On Error Wait for further confirmation while an error occurs.
Page 91: Item's Parameters Configuration
3.3 Option 3 Diagnostic Programs LOOPBOUND The chosen test items will run repeatedly according to the times specified in the 'Number of Loops'. TIMEBOUND The chosen test items will run for an extent time specified in 'Time Limit Hrs' and 'Time Limit Min'.
Page 92: Load Batch Parameters
3 Diagnostic Programs 3.3 Option Parameters • For the test items with specific parameters, this option will call the related configuration screens. Otherwise, the program will show the following dialogue window: Parameters for the specific test items: Some test items (Memory, HDD, e g...) have their individual parameters, which can be configured in their parameters setting window.
Page 93: Log Parameters Setting
3.3 Option 3 Diagnostic Programs 3.3.6 LOG Parameters Setting… You can access the Log Parameters screen through Service Diagnostics\Options - Generate Report. Report Destination • With 'NONE' selected, no log file will be generated; With 'FILE' selected, a log file with the name specified in 'Log File Name' will be generated.
Page 94: Specify Log Viewer
3 Diagnostic Programs 3.3 Option With this parameter selected, the start time of the test will be recorded. Log Test End Time With this parameter selected, the end time of the test will be recorded. Log Errors Only With this parameter selected, errors will be recorded only when the test fails. Log Errors Only with Time With this parameter selected, errors and time will be recorded only when the test fails.
Page 95: Log Viewer
3.3 Option 3 Diagnostic Programs In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer: ↑, ↓ • Scroll a line backward or forward on the screen. Page Up, Page Down •...
Page 96 3 Diagnostic Programs 3.3 Option • Exit the Log viewer. • Display the Help information about the Logviewer operations and the functional keys. Ctrl+Home • Go to the start of the log file. Ctrl+End • Go to the end of the log file. Ctrl+F3 •...
Page 97: Subtests
3.4 Subtests 3 Diagnostic Programs Subtests Test Test Group Subtest Test items Item ID System Basic Functionality Test CPU Speed Coprocessor NPU Basic Functions NPU Interrupt CPU Information CPU Protected Mode Speedstep Board DMA Controller Interval Timer Clock / Calendar Speaker PCI System Plug and Play...
Page 98 3 Diagnostic Programs 3.4 Subtests Cache Memory Random Memory Randomize Test Random Increment Read/Write Data Bus Test Memory Speed Test Storage Sequential/Random R/W Sequential/Random Seek Performance Controller Check Diagnostic Read/Write SMART Test CDROM Controller Test Data Transfer Rate Audio CD Play Data CD Butterfly Seek Data CD Random Seek Data CD Sequence Seek...
Page 99 3.4 Subtests 3 Diagnostic Programs VESA 1024x768x64K Mode VESA 1024x768x16M Mode VESA 1024x768x32bit Mode 1280X1024 Video Modes VESA 1280x1024x32K Mode VESA 1280x1024x64K Mode VESA 1280x1024x16M Mode VESA 1280x1024x32bit Mode 1400X1050 Video Modes VESA 1400x1050x32K Mode VESA 1400x1050x64K Mode VESA 1400x1050x16M Mode VESA 1400x1050x32bit Mode 1600X1200 Video Modes VESA 1600x1200x32K Mode...
Page 100 3 Diagnostic Programs 3.4 Subtests IrDA Slave LAN Card Device ID Detection Vendor ID Detection Mac Address Detection SD Card Write/Read Test Lock Test Peripheral Keyboard Keyboard Map Keyboard Data Line Keyboard Led Keyboard Clock Line Mouse Dual Point PS2 Mouse TECRA S1Maintenance Manual Downloaded from www.Manualslib.com...
Page 101: System Test
3.5 System Test 3 Diagnostic Programs System Test Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU 1.
Page 102 3 Diagnostic Programs 3.5 System Test Expected CPU Speed--Specify the expected CPU Speed value you want for further comparison. 3. Coprocessor NPU Basic Functions Test This test item is to check whether the precision of the numeric processor in the float calculation is up to the IEEE standards. NPU Interrupt Test This test item is to check whether NPU transfers the abnormal Interrupt program correctly by forcing an abnormal float.
Page 103 3.5 System Test 3 Diagnostic Programs supply mode. In this test item, the user is requires to operate on the screen prompted. Below is the parameter dialog window of CPU Speedstep test item: Speed Change Comparison—When ‘No’ is chosen, system only reports the CPU speed at the different power supply.
Page 104 3 Diagnostic Programs 3.5 System Test This test item is to check whether the speaker currently used works normally. It requires the user respond to the test instructions. 5. PCI System This test item is to check whether the bus number, device number and function number in PCI bus are valid.
Page 105 3.5 System Test 3 Diagnostic Programs TECRA S1Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 106: Memory Test
3 Diagnostic Programs 3.6 Memory Test Memory Test This test module is to check whether the memory chip works normally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that includes two sub-items -- ROM Read and ROM Write Protection.
Page 107 3.6 Memory Test 3 Diagnostic Programs 1. Bit Stuck High Test Data pattern: Every bit is ‘1’ (Each bit is high) 2. Bit Stuck Low Test Data pattern: Every bit is ‘0'(Each bit is low); 3. Checker Board Test Data pattern: Lo-byte and hi-byte are composed with 0101(0x5) and 1010 (0xA);...
Page 108: Memory Test
3 Diagnostic Programs 3.6 Memory Test Extended Memory Start Address and Extended Memory End Address (MB): Set the range of extended memory that is to be tested. The test coverage will base on the value setting in ‘Percent (%)’ mentioned at below. Percent (%): Choose the percentage of the defined range of the memory to be tested.
Page 109 3.6 Memory Test 3 Diagnostic Programs The test item is to check whether the CPU internal cache memory could be accessed correctly. Subtest 09 Random Memory Random Memory test includes the following two test items: Randomize Test and Random Incremental Read/Write Test. The parameter dialog window is the same as that in ‘Subtest 03 Extended Pattern’.
Page 110: Storage
3 Diagnostic Programs 3.7 Storage Storage Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified when the HDD test is being done.
Page 111 3.7 Storage 3 Diagnostic Programs (1) Read & Write –Write data on the disk, then read it out and compare the two value; (2) Read Verify —Read data only; (3) Unprotected Write—Write data on the disk without backup original data. Option—Select sequential test or random test 2.
Page 112 3 Diagnostic Programs 3.7 Storage Retry--Specify the maximum retrying times whether the operation fails. 4. Controller Check Check the HDD controller’s status, including HDD interrupt and unexpected interrupt. 5. Diagnostic Read/Write This test item is a quick test to verify whether the HDD could be correctly accessed and the user could specify the percentage in the below dialog.
Page 113: Storage
3.7 Storage 3 Diagnostic Programs 3. Audio CD Play This test item is to check whether the audio play normally. It needs an audio CD. Start/End Track Number-- Specify the Track range to be played; Time (1-20) -- Specify the time each track to be played. 4.
Page 114: Video
3 Diagnostic Programs 3.8 Video Video This test item tests the video by displaying the figures in different graphic mode displaying the property and color of the characters in different text mode. User will judge whether the display is correct to confirm whether each video mode works normally.
Page 115 3.8 Video 3 Diagnostic Programs It would display the below texts of the different attributes in the screen 1. Text in normal attribute; 2. Text in blinking normal attribute; 3. Text in inverse attribute; 4. Text in blinking inverse attribute; 5.
Page 116 3 Diagnostic Programs 3.8 Video 4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a character defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colors (dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and white besides the above 8 colors).
Page 117 3.8 Video 3 Diagnostic Programs Subtest 02 640 * 480 VGA Mode This test item is to check whether 680*480 VGA Text mode works normally. In the test, user is required to respond based on the instruction in the screen. Subtest 03 VESA Video Modes This test item is to check whether all the video modes supported by the video card...
Page 118: Video
3 Diagnostic Programs 3.8 Video 2. 800X600 Video Modes Test 3. 1024X768 Video Modes Test 4. 1280 x1024 Video Modes Test 5. 1400 X1050 Video Modes Test 6. 1600 X1200 Video Modes Test Subtest 04 VESA Video Memory This test item is to check whether VESA video memory could be correctly accessed (write data &...
Page 119 3.8 Video 3 Diagnostic Programs Subtest 06 AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally. Subtest 07 LCD Panel Test This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens.
Page 120 3 Diagnostic Programs 3.8 Video Subtest 11 DAC/Palette Address This test item is to check the function of DAC registers and Palette registers. In the test, user is required to respond based on the instruction in the screen. Subtest 12 BitBlt Engine Test This test item is to check whether the BitBlt engine works normally.
Page 121 3.8 Video 3 Diagnostic Programs What should be done is to write the data of the type of BitBLT operation and the location of BitBLT source area and destination area into the BitBLT registers, and all those operations will be completed automatically by BitBLT engine with minimum CPU intervention.
Page 122: Communication (Comm)
3 Diagnostic Programs 3.9 Communication Communication (COMM) Subtest 01 This test item is to check whether there is open or short circuit issue in the external pins by looping back the external pins, controlling the voltage of each data pin, control pin and status pin.
Page 123 3.9 Communication 3 Diagnostic Programs Check whether it supports ECP (Extended Capabilities Port) feature. 5. Printer Check Check whether it could connect to a standard LPT printer and print out the text correctly. Here are some samples of LPT printers. HP DeskJet 200 EPSON STYLUS COLOR 440 EPSON STYLUS COLOR 460...
Page 124 3 Diagnostic Programs 3.9 Communication Check whether COM port register could be correctly accessed and works normally. 2. IRQ Check Check the COM port’s IRQ function. Below is the parameter dialog window of the IRQ Check. Parity: Choose the parity mode; Stop Bit: Choose the stop bit;...
Page 125 3.9 Communication 3 Diagnostic Programs Stop Bit: Choose the stop bit; Word Size: Choose the bit number in one word; Baud Start/End: Select the start baud rate and end baud rate.All the baud rates between the start and end baud rate would be tested in the test. 4.
Page 126 3 Diagnostic Programs 3.9 Communication Connect Timeout: Define the time that slave connecting to master (in seconds); Test Timeout: Define the time that testing each transfer rate(in seconds); SIR Test: Choose the transfer rates to be checked in Slow IR; FIR Test: Choose the transfer rates to be checked in Fast IR.
Page 127 3.9 Communication 3 Diagnostic Programs Below is the Master Testing window: Subtest 04 LAN Card This test item is to check whether the module can detect the existence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card.
Page 128: Peripheral
3 Diagnostic Programs 3.10 Peripheral 3.10 Peripheral Subtest 01 Keyboard This test item is to check whether the keyboard works normally. 1. Keyboard Map This test item is to check whether each key in the keyboard works normally. It requires user to press the key and check whether the key in the screen change color.
Page 129 3.10 Peripheral 3 Diagnostic Programs 1: AC Power LED 2: DC Power LED 3: Battery LED 4: HDD access LED 5: FDD LED 6: CAP/Number/Scroll LED Yellow Green Subtest 02 Mouse Test Check whether the point devices, such as mouse, can work normally. 1.
Page 130 3 Diagnostic Programs 3.10 Peripheral Based on the area that the yellow arrow indicates, user should press the corresponding button area in the Touch Pad. If the corresponding area in the screen turns yellow, successful, otherwise fail. During the Enhanced test mode, test method is the same as Standard Test. 2.
Page 131 3.10 Peripheral 3 Diagnostic Programs TECRA S1Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 132: Error Codes And Description
3 Diagnostic Programs 3.11Error Codes and Description 3.11 Error Codes and description The format of ‘Error Code’ is ‘ddxxee’, and ‘dd’ is the device ID (1~2 chars), ‘xx’ is test function ID of device (2 chars), ‘ee’ is the error code of device (2 chars); the range of error code is from 01 to 99 in each device (the common error codes in all device are set to 99 and spanned).
Page 133 3.11Error Codes and Description 3 Diagnostic Programs The ROM BIOS has Physical Test this unit on multiple Read Error problems. machines. The ROM BIOS has Physical Write-Protect Error As above. problems. The test pattern read out from the Base Memory Error base memory is different from Test this memory chip on Address...
Page 134 3 Diagnostic Programs 3.11Error Codes and Description Update-ended Interrupt R/W errors with the RTC As above. Error refreshing interrupt controller. The PC speaker's sound source -- -counter/timer 8253 can not RTC Alarm Error As above. produce corresponding timing signal. System Board Speaker The Speaker can not sound Check the volume tuner.
Page 135 3.11Error Codes and Description 3 Diagnostic Programs 1) Check whether there is any 1) Physical problems with the physical problem with the video video card. card. VGA Mode Error 2) Physical problems with the 2) Check whether there is any monitor.
Page 136: Audio
DTR/STR Connection As above. As above. Error Toshiba Fixture Error As above. As above. No Paper No papers in the printer. Check for papers in the printer. TECRA S1Maintenance Manual Downloaded from www.Manualslib.com...
Page 137 3.11Error Codes and Description 3 Diagnostic Programs Check and see whether the printer OFF Line No papers in the printer. is connected to the computer. Check and see whether the printer Power OFF No papers in the printer. is supplied with power. No Printer Found.
Page 138 3 Diagnostic Programs 3.11Error Codes and Description Modem Status Change The Modem Status Change As above. Interrupt Error Interrupt cannot be invoked. 1) Whether the COM PORT does not support FIFO, this test should 1) UART version is below 16550 be ignored.
Page 139 3.11Error Codes and Description 3 Diagnostic Programs Data Line Test Fail Data Line Test fails. As above. 05xx Mouse PS2 Mouse Test Fail PS2 Mouse Test fails. Replace the mouse. Check the mouse connection and Dual Point Test Fail Dual Point Test fails. repeat the test.
Page 140 3 Diagnostic Programs 3.11Error Codes and Description Seek Error HD is damaged. As above. Disk Controller Self Test The HD controller is damaged. As above. Failed Disk Controller Test unexpected interrupt The HD controller is damaged. As above. Failed Disk Controller action The HD controller is damaged.
Page 141: Quick Test Item List
3.12 Quick Test Item List 3 Diagnostic Programs 3.12 Quick Test Item List Device Test Items Comment Basic Functionality NPU Basic Functions CPU Information Memory BIOS ROM Cache Memory Bit Stuck High Test Bit Stuck Low Test Address Test Board Interval Timer Clock / Calendar APM Functionality...
Page 142: Replacement Procedures
Chapter 4 Replacement Procedures Downloaded from www.Manualslib.com manuals search engine...
Page 143 4 Replacement Procedures 4-ii TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 144: Cooling Module
Installing the Cooling Module ................4-19 CPU.......................... 4-21 Removing the CPU .................... 4-21 Installing the CPU....................4-22 HDD......................... 4-24 Removing the HDD ................... 4-24 Installing the HDD..................... 4-26 Selectable Bay Module .................... 4-27 TECRA S1 Maintenance Manual 4-iii Downloaded from www.Manualslib.com manuals search engine...
Page 145 Installing the Top Cover with the Display Assembly........4-49 4.13 I/O Board ......................... 4-50 Removing the I/O Board..................4-50 Installing the I/O Board ..................4-50 4.14 System Board ......................4-51 Removing the System Board ................4-51 4-iv TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 146 Installing the FL Inverter Board ................ 4-56 4.17 LCD Modules......................4-57 Removing the 15.0-inch LCD module............... 4-57 Installing the 15.0-inch LCD Module..............4-59 Removing the 14.0-inch LCD module............... 4-60 Installing the 14.0-inch LCD Module..............4-62 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 147 Figure 4-26 Removing the screws from the bottom and of the computer ......4-42 Figure 4-27 Removing the speakers ................... 4-43 Figure 4-28 Removing the bluetooth card ................4-44 Figure 4-29 Removing the screws from the bottom of the computer ......... 4-46 4-vi TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 148 Figure 4-40 Removing the 15.0-inch LCD module ............4-58 Figure 4-41 Removing the 14.0-inch LCD module and screws ......... 4-60 Figure 4-42 Removing the 14.0-inch LCD module ............4-61 Figure 4-43 Removing the 14.0-inch LCD module ............4-61 TECRA S1 Maintenance Manual 4-vii Downloaded from www.Manualslib.com...
Page 149: General
• For removing the LCD Module First, remove the display mask and FL inverter board, both of which are shown above the LCD module. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 150: Safety Precautions
DANGER: Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. Never heat or disassemble the battery packs to avoid leakage of alkaline solutions.
Page 151 Inside the PC are components that become hot during operation (such as the CPU and cooling module). To avoid burns, let the hot components cool down before starting inspection or repair task. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 152: Before You Begin
To avoid personal injury, use care to handle components that have sharp edges or corners. After you have replaced an FRU, check that the FRU works correctly to ensure normal computer operation. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 153: Disassembly Procedures
Check that all the required screws are used to fix the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure firm FRU fixing. After installing an FRU, make sure that the FRU and computer can work normally. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 154: Tools And Equipment
0.153 N ･ m (1.5 kgf ･ cm) M2.5x4 PSP TITE screws 0.204 N ･ m (2.0 kgf ･ cm) M2.5x6 GIZA TITE screws 0.36 N ･ m (3.5 kgf ･ cm) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 155: Colors Of Screw Shanks
U (stands for unique-pan head screws, studs, etc.) Symbol examples 6 mm bind screw 12 mm bind screw 5 mm stud (The numeral represents the rounded length of the threaded portion irrespective of the entire stud length.) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 156: Removing The Battery Pack
2. Slide the battery release latch and remove the battery pack from the computer. Figure 4-1 Removing the battery pack NOTE: Dispose of the used battery packs as required by local ordinances or regulations. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 157: Installing The Battery Pack
1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click. 2. Slide in the battery lock. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 158: Removing The Optional Pc Card
2. When the eject button popped out slightly, push it again. 3. When the PC card popped out, grasp it and pull it out. Figure 4-2 Removing the PC card 4-10 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 159: Installing The Optional Pc Card
After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card in compatible with the current hardware configuration. TECRA S1 Maintenance Manual 4-11 Downloaded from www.Manualslib.com...
Page 160: Removing The Optional Memory
3. Remove the memory cover. CAUTION: Do not touch the connectors on the memory modules or in the computer. Contaminated connectors can cause memory access problems. Figure 4-3 Removing the memory cover 4-12 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 161 4. Spread out the two memory lock stoppers so that the memory module can be raised. 5. Pull the memory module up and out at an angle, using care to the connectors. Figure 4-4 Removing the optional memory TECRA S1 Maintenance Manual 4-13 Downloaded from www.Manualslib.com...
Page 162: Installing The Optional Memory
TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections. CAUTION: To prevent system malfunctions, always use Slot A first to insert the memory modules. 4-14 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 163: Removing The Mdc Card
3. Remove the MDC cover. CAUTION: Do not touch the connectors on the MDC card or in the computer. Contaminated connectors can cause MDC card failures. Figure 4-5 Removing the MDC cover TECRA S1 Maintenance Manual 4-15 Downloaded from www.Manualslib.com...
Page 164 5. Raise the MDC card and disconnect it from CN1006 on the system board. 6. Disconnect the MDC cable from the connector JP1 on the MDC card. Figure 4-6 Removing the MDC card 4-16 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 165: Installing The Mdc Card
After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed MDC card has been recognized by the system. If it has not been recognized yet, check the connections. TECRA S1 Maintenance Manual 4-17 Downloaded from www.Manualslib.com...
Page 166: Cooling Module
1. Disconnect the cable of the cooling module from CN1007 on the system board. 2. Release the four cooling module fix screws according the order 1 till 4. 3. Remove the cooling module. Figure 4-7 Removing the cooling module 4-18 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 167: Installing The Cooling Module
NOTE: Apply silicon greases with a special syringe to cover the surface of the CPU chip completely. CPU chip Figure 4-8 Applying silicon greases TECRA S1 Maintenance Manual 4-19 Downloaded from www.Manualslib.com manuals search engine...
Page 168 2. Place the cooling module in the correct position. 3. Fasten the four cooling module fix screws according to the order 1 till 4. 4. Connect the cooling module cable to CN1007 on the system board. 4-20 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 169: Cpu
1. Unlock the CPU by rotating the cam on the CPU socket 180 degrees to the left with a flat-blade screwdriver (in the order shown in the figure below). 2. Remove the CPU. Figure 4-9 Removing the CPU TECRA S1 Maintenance Manual 4-21 Downloaded from www.Manualslib.com...
Page 170: Installing The Cpu
2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide. Figure 4-10 Installing the CPU CAUTION: Place the CPU by aligning the triangle with the shaded area. 4-22 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 171 4.3 CPU 4 Replacement Procedures 3. Secure the CPU by rotating the cam 180 degrees to the right with a flat-blade screwdriver. Figure 4-11 Securing the CPU TECRA S1 Maintenance Manual 4-23 Downloaded from www.Manualslib.com manuals search engine...
Page 172: Hdd
1. Remove one M2.5x3.5 black flat-head screw for fixing the HDD pack. 2. Remove the HDD pack sliding it in the direction of the arrows. Figure 4-12 Removing the HDD pack 4-24 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 173 5. Remove the HDD chassis. 6. Remove the HDD connector. Figure 4-13 Removing the HDD chassis CAUTION: Do not apply pressure to the top or bottom of the drive. TECRA S1 Maintenance Manual 4-25 Downloaded from www.Manualslib.com manuals search engine...
Page 174: Installing The Hdd
3. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides. 4. Insert the HDD pack. 5. Secure the HDD cover with one M2.5x4 black flat-head screw. 4-26 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 175: Selectable Bay Module
For removing the selectable bay cover, see the explanations of "Disassembling the CD-ROM Drive." CAUTION: Handle the selectable bay module carefully, because it becomes hot during operation. Figure 4-14 Removing the selectable bay module TECRA S1 Maintenance Manual 4-27 Downloaded from www.Manualslib.com manuals search engine...
Page 176: Installing The Selectable Bay Module
Install the selectable bay module according to the following procedures and Figure 4-14. 1. Place the selectable bay module in the correct position and slide it in. 2. Push it until it clicks into place. 4-28 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 177: Disassembling The Dvd-Rom Drive
2. Remove the connector cover and connector from the DVD-ROM drive. Figure 4-16 Removing the connector from the DVD-ROM drive 3. Remove the five M2x3 white super flat-head screws. 4. Remove the frame. TECRA S1 Maintenance Manual 4-29 Downloaded from www.Manualslib.com...
Page 178: Assembling The Dvd-Rom Drive
2. Secure the frame with the five M2x3 white super flat-head screws. 3. Attach the connector and connector cover to the DVD-ROM drive, and secure them with the two M2x8 black bind screws. 4-30 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 179: Touch Pad
- Five bottom latches 3. Push the touch pad toward right and release the five bottom latches. Figure 4-17 Removing the touch pad 4. Disconnect the touch pad cable from CN8. TECRA S1 Maintenance Manual 4-31 Downloaded from www.Manualslib.com manuals search engine...
Page 180: Installing The Touch Pad
3. Place the touch pad in the correct position and fasten the following 15 latches, in that order: - One latch on the left and three latches on the right sides - Six top latches - Five bottom latches 4-32 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 181: Disassembling The Touch Pad
3. Remove the touch pad holder by sliding it in the direction of the arrow. Figure 4-19 Removing the touch pad holder 4. Release the two latches on the touch pad cover. Figure 4-20 Removing the touch pad cover TECRA S1 Maintenance Manual 4-33 Downloaded from www.Manualslib.com...
Page 182: Assembling The Touch Pad
3. Push it until it into place. 4. Secure it with the two M2x3 white flat-head screws. 5. Connect the touch pad cable to the connector CN1 on the touch pad. 4-34 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 183: Rtc Battery
RTC Batteries WARNING: To replace RTC (real-time clock) batteries, always use genuine batteries or replacement batteries authorized by Toshiba. Using batteries other than those can cause battery explosions or other damage. Never use an RTC battery that looks abnormal. Replace it with a new one, and dispose of the old battery as required by local ordinances or regulations.
Page 184: Removing The Rtc Battery
Install the RTC battery according to the following procedures and Figure 4-21. 1. Connect the RTC battery cable to the RTC battery connector on the system board. 2. Place the RTC battery in the correct position. 4-36 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 185: Wireless Lan Card
2. Spread out both the left and right stoppers for fixing the wireless LAN card until the card can be raised. Figure 4-22 Removing the wireless LAN card 3. Pull the wireless LAN card up and out at an angle. TECRA S1 Maintenance Manual 4-37 Downloaded from www.Manualslib.com...
Page 186: Installing The Wireless Lan Card
CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. 4-38 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 187: Keyboard
4. Release the following 6 latches on the switch cover, in that order: - Three bottom latches - One latch on the left and right sides - One middle latches TECRA S1 Maintenance Manual 4-39 Downloaded from www.Manualslib.com manuals search engine...
Page 188 6. Move the keyboard in the direction of the arrow until the keyboard connector appears. 7. Disconnect the keyboard cable from CN7 on the system board and remove the keyboard. Figure 4-25 Removing the keyboard 4-40 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 189: Installing The Keyboard
- Three bottom latches - One latch on the left and right sides - One middle latch 5. Turn the computer upside down and secure two M2.5x12 black bind screws. TECRA S1 Maintenance Manual 4-41 Downloaded from www.Manualslib.com manuals search engine...
Page 190: Speakers
4. Remove the speaker cables from the guides (grooves) on the top cover. 5. Remove the left and right speakers. Figure 4-26 Removing the screws from the bottom and back of the computer 4-42 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 191: Installing The Speakers
3. Restore the normal harness cover placement. Fix it with the M2.5x3.5 black flat-head screw. 4. Turn the computer upside down, and secure them with the M2.5x6 black bind screws (Two screws for one speaker). TECRA S1 Maintenance Manual 4-43 Downloaded from www.Manualslib.com...
Page 192: Bluetooth Card
Bluetooth cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. Figure 4-28 Removing the Bluetooth card 3. Disconnect the SUMI-cards (flat cables) from CN2 on the system board. 4. Remove the Bluetooth card. 4-44 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 193: Installing The Bluetooch Card
CAUTION: Do not touch the connectors on the Bluetooth card and in the computer with bare hands. Bluetooth cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. 4. Secure the Bluetooth card with one M2x3 white flat-head screw. TECRA S1 Maintenance Manual 4-45 Downloaded from www.Manualslib.com...
Page 194: Top Cover With The Display Assembly
2. Restore the normal computer placement and open the display panel. Disconnect the LCD/FL cable from CN3 on the system board. 3. Remove the wireless antenna cables from the guides (grooves) on the top cover. 4. Remove the display module. 4-46 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 195 5. Turn the computer upside down, and remove the following 12 screws: - Seven M2.5x4 black bind screws - Five M2.5x3.5 black flat-head screw Figure 4-31 Removing the screws from the bottom of the computer TECRA S1 Maintenance Manual 4-47 Downloaded from www.Manualslib.com...
Page 196 8. Disconnect the MIC cable from CN13. 9. Disconnect the speaker extended cable from CN5005 10. Remove the top cover, using care to the two latches at the front and the middle. 4-48 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 197: Installing The Top Cover With The Display Assembly
9. Connect the LCD/FL cable to CN3 on the system board. 10. Close the display panel and turn the computer upside down and fix it with two M2.5x6 black bind screws. TECRA S1 Maintenance Manual 4-49 Downloaded from www.Manualslib.com...
Page 198: I/O Board
2. Place the I/O board in the correct position. 3. Secure the I/O board with the M2.5x3.5 black flat-head screw. 4. Connect the SUMI-card to CN5 on the system board. 4-50 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 199: System Board
1. Remove the one M2.5x3.5 black flat-head screws for securing the system board. 2. Remove the lever of the slide switch. 3. Remove the system board. Figure 4-34 Removing the system board TECRA S1 Maintenance Manual 4-51 Downloaded from www.Manualslib.com...
Page 200: Installing The System Board
2. Place the system board in the correct position and secure it with the one M2.5x3.5 black flat-head screws. 3. Fasten the one M2.5x3.5 screws and fix the system board to the base cover. 4-52 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 201: Display Mask
3. Release the following 18 latches on the display mask, in that order: - Six bottom latches - Four latches on each of the left and right sides - Four top latches Figure 4-35 Removing the display mask TECRA S1 Maintenance Manual 4-53 Downloaded from www.Manualslib.com manuals search engine...
Page 202: Installing The Display Mask
- Two rubber bumps on the top - Two silver seals on each of the left and right sides - Two black seals on the bottom 4-54 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 203: Fl Inverter Board
Remove the FL inverter board according to the following procedures and Figures 4-36 and 4- 1. Remove the M2x3 white bind screw. Figure 4-36 Removing the FL inverter board 2. Raise the FL inverter board and disconnect the LCD/FL cable from CN1. TECRA S1 Maintenance Manual 4-55 Downloaded from www.Manualslib.com...
Page 204: Installing The Fl Inverter Board
1. Connect the LCD/FL cable to CN1, and connect the HV cable to CN2. 2. Place the FL inverter board in the correct position. 3. Fasten the M2x3 white bind screw to secure the FL inverter board. 4-56 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 205: Lcd Modules
2. Carefully tilt the LCD module toward you. 3. Remove the two M2x3 white bind screws on each of the left and right sides for fixing the LCD bracket. Figure 4-38 Removing the 15.0-inch LCD module and screws TECRA S1 Maintenance Manual 4-57 Downloaded from www.Manualslib.com...
Page 206 5. Turn the LCD upside down. 6. Remove the LCD/FL cable connector. Then disconnect the LCD/FL cable. Figure 4-39 Removing the 15.0-inch LCD module Figure 4-40 Removing the 15.0-inch LCD module 4-58 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 207: Installing The 15.0-Inch Lcd Module
5. Place the LCD module in the correct position and secure it with the two M2.5x3.5 black flat-head screws and two M2x3 white bind screws. TECRA S1 Maintenance Manual 4-59 Downloaded from www.Manualslib.com...
Page 208: Removing The 14.0-Inch Lcd Module
3. Remove the four M2x3 white bind screws on each of the left and right sides for fixing the LCD bracket. Figure 4-41 Removing the 14.0-inch LCD module and screws 4-60 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 209 4.17 LCD Module 4 Replacement Procedures 4. Remove the LCD/FL cable connector. Then disconnect the LCD/FL cable. Figure 4-42 Removing the 14.0-inch LCD module Figure 4-43 Removing the 14.0-inch LCD module TECRA S1 Maintenance Manual 4-61 Downloaded from www.Manualslib.com manuals search engine...
Page 210: Installing The 14.0-Inch Lcd Module
3. Place the LCD module in the correct position and secure it with the two M2.5x3.5 black flat-head screws and two M2x3 white bind screws. 4-62 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 211 6000 1 次 Appendices Downloaded from www.Manualslib.com manuals search engine...
Page 212 Appendices App-ii TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 213 CN8 Touch Pad Connector (12-Pin) ..............C-16 C.20 CN1002 RJ45 (8-PIN+2LED)/RJ11 Connector (4-Pin) ........C-16 C.21 CN1 Internal Left Speaker Connector (3-Pin) ............ C-16 C.22 CN4 Internal Right Speaker Connector (3-Pin) ..........C-17 TECRA S1 Maintenance Manual App-iii Downloaded from www.Manualslib.com manuals search engine...
Page 214: Keyboard Scan/Character Codes
Serial Port Direct Cable (9-Pin to 9-Pin) ..............F-2 Serial Port Direct Cable (9-Pin to 25-Pin) ..............F-2 Appendix G BIOS Rewrite Procedures ................G-1 Appendix H EC/KBC Rewrite Procedures..............H-1 App-iv TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 215 Appendices TECRA S1 Maintenance Manual App-v Downloaded from www.Manualslib.com manuals search engine...
Page 216 PS/2 Mouse/keyboard connector pin assignments (6-Pin) ......C-14 Table C-15 TV OUT connector pin assignments (2-Pin) ..........C-15 Table C-16 USB I/F connector pin assignments (4-Pin) ..........C-15 Table C-17 USB I/F connector pin assignments (4-Pin) ..........C-15 App-vi TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 217 Scan codes with Fn key................. D-6 Table D-5 Scan codes in overlay mode................D-7 Table D-6 No.124 key scan code ................... D-7 Table D-7 No.126 key scan code ................... D-8 TECRA S1 Maintenance Manual App-vii Downloaded from www.Manualslib.com manuals search engine...
Page 218: Appendix A Handling The Lcd Module
LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance. Also, the panel’s polarized surface is easily scarred, so be carefully when handling it. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 219 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 220 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 221 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 222 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 223 Appendices Apx. A Handling the LCD Module TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 224: Appendix B Board Layout
Appendices Appendix B Appendix B Board Layout System Board Front View Figure B-1 Board layout (front) C’ D’ A’ B’ E’ F’ G’ K’ I’ N’ L’ J’ M’ H’ TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 225 RTC Battery Connector I’ MINI PCI Connector J’ CN11 BIOS IC (Flash ROM) K’ ICH3-M-South Bridge L’ Jack 2 Headphone Connector M’ Jack 1 Ext_Microphone Connector N’ CN10 SD Connector TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 226 Apx. B Board Layout Appendices Figure B-2 Board layout ( back ) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 227 Memory Slot A Connector ( 2) CN1014 Main Battery Connector CN5000 USB I/F Connector A CN5003 System/B I/F Connector CN5002 USB I/F Connector C CN5004 PS2 Mouse / Keyboard Connector CN5001 USB I/F Connector B TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 228: Appendix C Pin Assignments
/M_DATA_R_(11) /M_DATA_R_(15) +V2.5 +V2.5 /M_CLK_DDR2 +V2.5 /M_CLK_DDR2# DGND DGND DGND /M_DATA_R_(16) /M_DATA_R_(20) /M_DATA_R_(17) /M_DATA_R_(21) +V2.5 +V2.5 /M_DQS_R(2) DGND /M_DATA_R_(18) /M_DATA_R_(22) DGND DGND /M_DATA_R_(19) /M_DATA_R_(23) /M_DATA_R_(24) /M_DATA_R_(28) +V2.5 +V2.5 /M_DATA_R_(25) /M_DATA_R_(29) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 229 /M_A_FR_(9) /M_A_FR_(8) DGND DGND /M_A_FR_(7) /M_A_FR_(6) /M_A_FR_(5) /M_A_FR_(4) /M_A_FR_(3) /M_A_FR_(2) /M_A_FR_(1) /M_A_FR_(0) +V2.5 +V2.5 /M_A_FR_(10) /M_BS1_FR# /M_BS0_FR# /M_RAS_FR# /M_WE_FR# /M_CAS_FR# /M_CS0_R# /M_CS1_R# DGND DGND /M_DATA_R_(32 /M_DATA_R_(36) /M_DATA_R_(33 /M_DATA_R_(37) +V2.5 +V2.5 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 230 /M_DATA_R_(58) /M_DATA_R_(62) /M_DATA_R_(59) /M_DATA_R_(63) +V2.5 +V2.5 /ICH_SMDAT_3 DGND /ICH_SMCLK_3 DGND +V3S DGND CN1013 Memory Slot B Connector (2) (200-Pin) Table C-2 Memory slot B connector (2) pin assignments (200-PIN) (1/3) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 231 /M_DATA_R_(11) /M_DATA_R_(15) +V2.5 +V2.5 /M_CLK_DDR5 +V2.5 /M_CLK_DDR5# DGND DGND DGND /M_DATA_R_(16) /M_DATA_R_(20) /M_DATA_R_(17) /M_DATA_R_(21) +V2.5 +V2.5 /M_DQS_R(2) DGND /M_DATA_R_(18) /M_DATA_R_(22) DGND DGND /M_DATA_R_(19) /M_DATA_R_(23) /M_DATA_R_(24) /M_DATA_R_(28) +V2.5 +V2.5 /M_DATA_R_(25) /M_DATA_R_(29) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 232 /M_A(8) DGND DGND /M_A(7) /M_A(6) /M_A(5) /M_A(4) /M_A(3) /M_A(2) /M_A(1) /M_A(0) +V2.5 +V2.5 /M_A(10) /M_BS1# /M_BS0 # /M_RAS# /M_WE# /M_CAS# /M_CS2_R# /M_CS3_R# DGND DGND /M_DATA_R_(32 /M_DATA_R_(36) /M_DATA_R_(33 /M_DATA_R_(37) +V2.5 +V2.5 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 233: Cn3 Lcd/Fl Inverter Connector (40-Pin
/M_DATA_R_(61) /M_SQS_R(7) DGND DGND DGND /M_DATA_R_(58) /M_DATA_R_(62) /M_DATA_R_(59) /M_DATA_R_(63) +V2.5 +V2.5 /ICH_SMDAT_3 +V3S /ICH_SMCLK_3 DGND +V3S DGND CN3 LCD/FL Inverter Connector (40-Pin) Table C-3 LCD/FL inverter connector pin assignments (40-pin) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 234: Cn1000 External Monitor Connector (15-Pin
VGAGND VGAGND VGAGND +V5S DDCSDA-P5P HSYNC SVSYNC-P5P DDCCLK-P5P CN1011 PC Card Slot Connector (150-Pin) Table C-5 PC card slot connector pin assignments (150-pin) (1/3) Pin No. Signal Name Signal Name TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 235 ACARDVCC ACARDVCC ACRADVPP /A_CADR(16)_R /A_CTRDY# /A_CIRDY# DGND /A_CFRAME# /A_CCBE2# /A_CAD(17) /A_CAD(18) /A_CAD(19) /A_CAD(20) /A_CVS2 DGND /A_CAD(21) /A_CRST# /A_CAD(22) /A_CSERR# /A_CAD(23) /A_CREQ# /A_CAD(24) DGND /A_CCBE3# /A_CAD(25) /A_CAUDIO /A_CAD(26) /A_CSTSCHG /A_CAD(27) /A_CAD(28) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 236 BCARDVCC BCARDVPP /B_CADR(16)_R /B_CTRDY /B_CIRDY# DGND /B_CFRAME# /B_CCBE2# /B_CAD(17) /B_CAD(18) /B_CAD(19) /B_CAD(20) /B_CVS2 DGND /B_CAD(21) /B_CRST# /B_CAD(22) /B_CSERR# /B_CAD(23) /B_CREQ# /B_CAD(24) DGND /B_CCBE3# /B_CAD(25) /B_CAUDIO /B_CAD(26) /B_CSTSCHG /B_CAD(27) /B_CAD(28) DGND TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 237: Cn1007 Cooling Module Connector (3-Pin
SCAN_IN(1) SCAN_OUT(9) SCAN_OUT(8) SCAN_OUT(7) SCAN_IN(0) SCAN_OUT(6) SCAN_OUT(5) SCAN_OUT(4) SCAN_OUT(3) SCAN_OUT(2) SCAN_OUT(1) SCAN_OUT(0) +V5S CAPS_LED#3 SCROLL_LED#3 NUM_LED#3 CN2 Bluetooth I/F Connector (20-Pin) Table C-8 Bluetooth I/F connector pin assignments (20-Pin) C-10 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 238: Cn1006 Mdc Connector (30-Pin
BTWAKEUP BT_RESET# BTMDL# DGND CN1006 MDC Connector (30-Pin) Table C-9 MDC connector pin assignments (30-Pin) Pin No. Signal Name Signal Name PHONE MDC-B3V MDC-B3V FRAME_SYNC_ICH SDATA_OUT_ICH CODEC_RST#_ICH SDATA_IN1_ICH BITCLK_3_ICH TECRA S1 Maintenance Manual C-11 Downloaded from www.Manualslib.com manuals search engine...
Page 239: Cn1010 Selectable Bay Connector (72-Pin
SDDRQ_35 DGND SDIOW#_3 DGND SDIOR#_3 DGND SDIORDY_35 SDDACK#_35 DGND IRQ15_3 SDA(1) +V5S_SBAY +V5S_SBAY +V5S_SBAY SDA(0) SDA(2) SDCS1#_3 SDCS3#_3 CD_LED# DGND SBAY_ID2 SBAY_ID1 SBAY_ID0 DGND DGND DGND DGND DGND DGND C-12 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 240: Cn1015 Hdd Connector (44-Pin
IRQ14_3 DGND PDACK#_35 PDIORDY_35 DGND PDIOR#_3 DGND PDIOW#_3 DGND PDDRQ_35 DGND PDD(15) PDD(0) PDD(14) PDD(1) PDD(13) PDD(2) PDD(12) PDD(3) PDD(11) PDD(4) PDD(10) PDD(5) PDD(9) PDD(6) PDD(8) PDD(7) DGND PDRST#_3 TECRA S1 Maintenance Manual C-13 Downloaded from www.Manualslib.com manuals search engine...
Page 241: Cn1001 Parallel Connector (25-Pin
DCTS_3 DRI#_3 C.14 CN5004 PS/2 Mouse/Keyboard Connector (6-Pin) Table C-14 PS/2 Mouse/keyboard connector pin assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name EXKBDT_IO MOUSDT_IO +V5S_IO EXKBCK_IO MOUSCK_IO C-14 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 242: Jack1001 Tv Out Connector (2-Pin
Signal Name +V5_IO USB_PN1_IO USB_PP1_IO C.18 CN5002 USB I/F Connector-C (4-Pin) Table C-18 USB I/F connector pin assignments (4-Pin) Pin No. Signal Name Pin No. Signal Name +V5_IO USB_PN2_IO USB_PP2_IO TECRA S1 Maintenance Manual C-15 Downloaded from www.Manualslib.com manuals search engine...
Page 243: Cn8 Touch Pad Connector (12-Pin
MDMTIP MDMRNG C.21 CN1 Internal Left Speaker Connector (3-Pin) Table C-21 Internal left speaker connector pin assignments (3-Pin) Pin No. Signal Name Pin No. Signal Name SPK_OUT_L- SPK_OUT_L+ DGND C-16 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 244: Cn4 Internal Right Speaker Connector (3-Pin
Signal Name Pin No. Signal Name WLON# PIRQC#_3 +V5S +V3S PIRQB#_3 CLK_MINIPCI_3R PCI_RESET#_3 +V3S MPCIREQ0#_3 MPCIGNT0#_3 +V3S PCI_AD(31) PCI_PME#_3 PCI_AD(29) PCI_AD(30) PCI_AD(27) +V3S PCI_AD(25) PCI_AD(28) PCI_AD(26) PCI_CBE#(3) PCI_AD(24) PCI_AD(23) PCI_AD(25) TECRA S1 Maintenance Manual C-17 Downloaded from www.Manualslib.com manuals search engine...
Page 245 PCI_FRAME#_3 CLKRUN#_3 PCI_TRDY# PCI_SERR#_3 PCI_STOP#_3 +V3S PCI_PERR#_3 PCI_DEVSEL#_3 PCI_CBE#(1) PCI_AD(14) PCI_AD(15) PCI_AD(13) PCI_AD(12) PCI_AD(11) PCI_AD(10) PCI_AD(9) PCI_AD(8) PCI_CBE#(1) PCI_AD(7) +V3S +V3S PCI_AD(6) PCI_AD(5) PCI_AD(4) PCI_AD(2) PCI_AD(3) PCI_AD(0) +V5S PCI_AD(1) C-18 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 246: Cn1004 Docking I/F Connecter (240 Pin + Power
Docking I/F connector (240 pin + power) (1/4) Pin No. Signal Name Pin No. Signal Name DSDKC DSDKC DCOUT DCOUT DOCDT1# IF_P5V MOUSCK EXKBCK DPCONF DDCCLK D_ROUT D_GOUT D_BOUT DVSYNC VOID VOID MDMRNG MDMTIP TECRA S1 Maintenance Manual C-19 Downloaded from www.Manualslib.com manuals search engine...
Page 247 Docking I/F connector (240 pin + power) (2/4) Pin No. Signal Name Pin No. Signal Name DCOUT DCOUT EJECTRQ# IF_P5V MOUSDT EXKBDT DDCDATA DHYNSC VOID VOID VOID VOID DCOUT DCOUT DOCK_I2C_CL IF_P5V +V5ALWAYS USB_PWR_EN USB_OC#4 C-20 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 248 DDCD#_3 DDSR#_3 DTXD_3 DRI#_3 PDATA(7) PDATA(6) PDATA(4) PDATA(1) PDATA(2) PDATA(0) P_STRB# +V3_ICHLAN VOID VOID TERMPL DCOUT DCOUT DOCK_I2C_DAT IF_P5V USB_PP4 USB_PN4 USB_PP5 USB_PN5 DOUTR+ DOUTR- DOUTL- DINL- DINR+ DRXD#_3 TECRA S1 Maintenance Manual C-21 Downloaded from www.Manualslib.com manuals search engine...
Page 249: Cn12 Rtc Battery Connector (2-Pin
Signal Name RTCVCC C.26 CN1014 Main Battery Connector (6-Pin) Table C-26 Main battery connector pin assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name PACK0_V+ BAT0_CLK BAT0_DATA THRM0 C-22 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 250: Cn1008 Select Battery Connector (6-Pin
C.29 CN10 SD Connector (12-Pin) Table C-29 SD connector pin assignments (12-Pin) Pin No. Signal Name Pin No. Signal Name SD_DAT3 SD_CMD VCC_SD SD_CLK SD_DAT0 SD_DAT1 SD_DAT2 SD_CD# SD_WP TECRA S1 Maintenance Manual C-23 Downloaded from www.Manualslib.com manuals search engine...
Page 251: Jack1 Ext_Microphone Connector (6-Pin
Signal Name Pin No. Signal Name INTMIC C.32 JACK2 Headphone Connector (6-Pin) Table C-32 Headphone connector pin assignments (6-Pin) Pin No. Signal Name Pin No. Signal Name HEADL HEADR HPON C-24 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 252 Signal Name Pin No. Signal Name +V5_IO +V5_IO +V5_IO +V5_IO +V5_IO +V5S_IO +V5S_IO MOUSDT_IO EXKBDT_IO MOUSCK_IO EXKBCK_IO GND_IO USB_OC#0_IO GND_IO USB_PN0_IO USB_PP0_IO GND_IO USB_PN1_IO USB_PP1_IO GND_IO USB_PN2_IO USB_PP2_IO GND_IO USB_OC#2_IO TECRA S1 Maintenance Manual C-25 Downloaded from www.Manualslib.com manuals search engine...
Page 253 Downloaded from www.Manualslib.com manuals search engine...
Page 254 CN1014 Main Battery Connector (6-Pin)............... C-22 C.27 CN1008 Select Battery Connector (6-Pin) ............. C-23 C.28 CN5 I/O(USB) I/F Connector (24-Pin)..............C-23 C.29 CN10 SD Connector (12-Pin)................. C-23 C.30 JACK1 Ext_Microphone Connector (6-Pin) ............C-24 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 255: Cn13 Int_Microphone Connector (2-Pin
Appendices Apx. C Pin Assignments C.31 CN13 Int_Microphone Connector (2-Pin)...............C-24 C.32 JACK2 Headphone Connector (6-Pin) ..............C-24 C.33 CN5003 SYSTEM/B I/F Connector (24-Pin)............C-25 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 256: Appendix D Keyboard Scan/Character Codes
Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Code set 2 Note Keytop Make Break Make Break ‘ ~ 7 & BkSp TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 257 Table D-1 Scan codes (set 1 and set 2) (2/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Caps Lock ‘ “ Enter Shift (L) No.102 , < . > Shift (R) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 258 Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Code set 2 Note Keytop Make Break Make Break Ctrl Alt (L) Space ALT (R) ← Home ↑ ↓ PgUp PgDn → TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 259 5. * This key corresponds to key No. 42 in a 102-key model. 6. * Refer to Table D-6, No. 124 key scan code. 7. * Refer to Table D-7, No. 126 key scan code. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...
Page 260 With left Shift With right Shift Set 1 E0 AA __________ E0 B6 E0 2A ___________ E0 36 Set 2 E0 F0 12 ________ E0 F0 59 E0 12 ___________ E0 59 TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 261 ← Home ↑ ↓ PgUp PgDn → Table D-4 Scan codes with Fn key Code set 1 Code set 2 Keytop Make Break Make Break CTRL LALT ARROW NUMERIC Scrl TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 262 Break Make Break (–) Table D-6 No.124 key scan code Shift Code set 1 Code set 2 Make Break Make Break Prt Sc Common Ctrl + Shift + Alt + TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 263 Table D-7 No.126 key scan code Shift Code set 1 Code set 2 Make Make Pause Common* E1 1D E1 F0 Ctrl* E0 46 7E E0 F0 *: This key generates only make codes. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 264: Appendix E Key Layout
Apx E Key Layout Appendices Apx. E Key Layout Appendix E Key Layout United States (US) Keyboard Figure E-1 US keyboard Figure E-2 UK keyboard TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 265: Appendix F Wiring Diagrams
Apx. F Wiring Diagrams Appendices Appendix F Appendix F Wiring Diagrams Parallel Port Wraparound Connector Figure F-1 Parallel port wraparound connector Serial Port Wraparound Connector Figure F-2 Serial port wraparound connector TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 266: Serial Port Direct Cable (9-Pin To 9-Pin
Serial Port Direct Cable (9-Pin to 9-Pin) Figure F-3 Serial port direct cable (9-pin to 9-pin) Serial Port Direct Cable (9-Pin to 25-Pin) Figure F-4 Serial port direct cable (9-pin to 25-pin) TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 267: Appendix G Bios Rewrite Procedures
(Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts. 6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com manuals search engine...
Page 268: Appendix H Ec/Kbc Rewrite Procedures
(maximum), depending on the conditions of the computer or ICs. The computer is not hung up. Allow sufficient time. Never reboot or turn off the power to the computer before the rewriting is completed. TECRA S1 Maintenance Manual Downloaded from www.Manualslib.com...

Toshiba TECRA S1 Maintenance Manual

Table of Contents

Chapter 4 Replacement Procedures

Chapter 1 Hardware Overview

Table of Contents

Chapter 2 Troubleshooting

Chapter 3 Diagnostic Programs

Chapter 3 Diagnostic Programs

Cooling Module

Appendix

Appendix A Handling the LCD Module

Appendix Contents

Appendix B Board Layout

Appendix C Pin Assignments

Appendix D Keyboard Scan/Character Codes

Appendix E Key Layout

Appendix F Wiring Diagrams

Appendix G BIOS Rewrite Procedures

Appendix H EC/KBC Rewrite Procedures

Quick Links

Chapters

Related Manuals for Toshiba TECRA S1

Summary of Contents for Toshiba TECRA S1