hit counter script
Husqvarna 340iBT Workshop Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Blower
  5. 340iBT
  6. Workshop manual
Husqvarna 340iBT Workshop Manual

Husqvarna 340iBT Workshop Manual

Hide thumbs Also See for 340iBT:
Table of Contents

Advertisement

Quick Links

Download this manual
Workshop manual
340iBT
English
1126 - 001 - 08.11.2019

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 340iBT

Summary of Contents for Husqvarna 340iBT

  • Page 1 Workshop manual 340iBT English 1126 - 001 - 08.11.2019...

  • Page 2: Table Of Contents

    Contents 1 Introduction 1.1 Document description..........3 1.2 Target group............3 1.3 Revisions..............3 1.4 Safety..............3 1.5 Servicing tools............3 2 Safety 2.1 Safety definitions............4 2.2 General safety instructions........4 2.3 Symbols on the product......... 4 2.4 Battery use and safety........... 4 2.5 Special safety instructions........4 3 Servicing data 3.1 Servicing data............

  • Page 3: Introduction

    1.5 Servicing tools The manual gives information about necessary servicing tools. Always use original tools from Husqvarna. 1126 - 001 - 08.11.2019 Introduction - 3...

  • Page 4: Safety

    2.5 Special safety instructions 2.3 Symbols on the product 2.5.1 To connect the battery to the product Start/stop (Digital user interface) WARNING: Only use Husqvarna original batteries in the product. Boost button (Digital user interface) 1. Charge the battery fully.

  • Page 5: Servicing Data

    3 Servicing data 3.1 Servicing data For products with mechanical user interface. 1126 - 001 - 08.11.2019 Servicing data - 5...
  • Page 6 For products with digital user interface. 6 - Servicing data 1126 - 001 - 08.11.2019...
  • Page 7 1126 - 001 - 08.11.2019 Servicing data - 7...
  • Page 8 For products with mechanical user interface. 8 - Servicing data 1126 - 001 - 08.11.2019...
  • Page 9 For products with digital user interface. 1126 - 001 - 08.11.2019 Servicing data - 9...

  • Page 10: Servicing Tools

    Note: It can be necessary to install firmware to a new 4.2.1 Common service tool spare part. Make sure that you know the Husqvarna The common service tool (CST) is used with a computer identification number (HID) of the new spare parts (not included) for Husqvarna products.
  • Page 11 (CST). The identification number is found on the spare part. 1. Remove the batteries from the product. 2. Connect the adapter cable (A) to the battery (B) and to the lower battery slot connector (C) on the product. 3. Start the product. 4.

  • Page 12: Repair Instructions

    5 Repair instructions 5.1 To assemble the tube and handle on the 6. Align the knobs (I) to each side of the joint swivel (F). product 1. Put the clamp (A) on the flexible tube (B) and push the flexible tube onto the blower outlet (C). 7.

  • Page 13: To Put The Product In Transportation Mode

    13. Attach the cable clamp to the flexible tube. Put the cable of the operation handle in the loop on the cable clamp. 5.5 To remove and install the harness 1. Remove the 5 screws to remove the harness. 5.2 To put the product in transportation mode 1.
  • Page 14 a) Make sure that the inner muffler does not cause CAUTION: Do not pull the wires. They are a blockage to the airflow from the batteries. easily damaged. 1. Remove the 2 screws that hold the air intake. 2. Remove the 9 screws and remove the motor cover b) The guide pins on the motor must align with the (A).

  • Page 15: To Disassemble And Assemble The Battery Holder

    d) Make sure that the air outlet is installed in the 3. Remove the 2 battery connectors (A) and the airflow correct position. cover (B). 5.7 To disassemble and assemble the battery holder WARNING: Disconnect the battery to prevent 4. Assemble in the opposite sequence. Make sure to short circuit.

  • Page 16: Electrical System

    5.8 Electrical system 5.8.1 Electrical diagram Electric Handle 340iBT-RoW Trigger 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 Blue ESD Handle Black Blue 1 2 3 4 5 6 7 8 9...
  • Page 17 3. Remove the power switch. CAUTION: Do not pull the wires. They are easily damaged. 1. Make a note of the Husqvarna identification number (HID) of the new user interface before you install it. The identification number is found on the new control unit.
  • Page 18 7. Push and hold the spring in the direction of the CAUTION: Do not pull the wires. They are power trigger. easily damaged. 1. Remove the operation handle from the handlebar. To remove and install the operation handle Refer to on page 16 .
  • Page 19 8. Assemble the operation handle. CAUTION: Do not pull the wires. They are easily damaged. 1. Install the ESD cable to the ESD catch. 2. Connect the user interface (A) and the main switch (B) to the main cable connectors (C). 9.
  • Page 20 3. Lift the plate. 3. Lift the plate. 4. Remove the strain relief (A). 4. Disconnect the motor cables. 5. Remove the motor. 5. Disconnect the connector (B). 6. Remove the main cable. 7. Install the main cable in opposite sequence. 5.8.4 To replace the motor 1.
  • Page 21 3. Put the motor axle in an vise. 5.8.6 To install the fan on the motor 1. Clean the motor axle. 2. Make sure that the 3 screws are tightened correctly. The torque must be 2 Nm. CAUTION: Do not cause damage to the 3.
  • Page 22 6. Use a press to carefully push (4-8 kN) the fan onto 7. Carefully push the press tool until the press tool the motor axle. Make sure that the pressure on the touches the motor shaft. The press tool is then press tool, fan and motor axle applies straight.
  • Page 23 5. Disconnect the connectors from the control unit. 6. Remove the control unit from the 4 support hooks. 7. Make a note of the Husqvarna identification number (HID) of the new control unit before you install it. The identification number is found on the new control unit.

  • Page 24: Troubleshooting

    6 Troubleshooting 6.1 Overhaul Examine the components of the product. You find repair and servicing instructions for each component in the related chapters of this manual. 6.2 Troubleshooting of products with digital user interface Symptom Possible causes Recommended step The product does not start. No LEDs The battery is defective.

  • Page 25: Troubleshooting Products With Mechanical User Interface

    6.3 Troubleshooting products with mechanical user interface Symptom Possible causes Recommended step The product does not start. Defective battery. Push the status button on battery to do a check of the battery. A minimum of 1 green LED must come on. Defective plug between battery and Make sure that the power connectors product.

  • Page 26: Troubleshooting Of The Battery And Battery Charger

    6.4 Troubleshooting of the battery and battery charger Symptom Possible causes Recommended step No LEDs flash on the battery when Defective battery. Replace the battery. you press the start button. A warning sign shows a constant red Defective battery. Replace the battery. light on the battery when the start but- ton is pressed.
  • Page 27 Symptom Possible causes Recommended step A green lamp on the charger comes Defective Battery. Put the battery in a QC330 charger. If on for approximately 5-10 seconds the same problem occurs, replace the when the battery is attached. After battery. that a red warning sign flashes on the Defective charger.

  • Page 28: Technical Data

    7 Technical data 7.1 Technical data 340iBT Motor Motor type BLDC (brushless) 36V Weight Weight without battery, kg/ lb 6.3/13.9 Noise emissions Sound power level, measured dB (A) Sound power level, guaranteed L dB (A) Water protection level All weather use...
  • Page 29 7.1.2 Approved battery chargers Battery charger QC330 QC500 Input voltage, V 100-240 100-240 Frequency, Hz 50-60 50-60 Power, W 1126 - 001 - 08.11.2019 Technical data - 29...
  • Page 30 30 - Technical data 1126 - 001 - 08.11.2019...
  • Page 31 1126 - 001 - 08.11.2019 Technical data - 31...
  • Page 32 1140434-26 2019-11-18...

Table of Contents