Related Manuals for GE Monogram ZXR8510
Summary of Contents for GE Monogram ZXR8510
-
Page 1: Installation Instructions
Installation Instructions If you have questions, call 800.GE.CARES or visit our website at: www.monogram.com ZXR858, ZXR859 and ZXR8510 Recirculating Accessories For Model ZV850, Island Vent Hood ®... -
Page 2: Table Of Contents
BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT • – Save these instructions for local inspector’s use. IMPORTANT • – Observe all governing codes and ordinances. Note to Installer • – Be sure to leave these instructions with the Consumer. Note to Consumer •... -
Page 3: Installation Preparation
Choose the correct kit according to ceiling heights: ZXR858 – For 8 ft. ceiling height. ZXR859 – For 9 ft. ceiling height ZXR8510 – For 10 ft. ceiling height. PRODUCT DIMENSIONS The vent hood must be installed 24″ min. and 30″ max. -
Page 4: Using Duct Cover Accessories
USING DUCT COVER ACCESSORIES A duct cover accessory is required for all ceiling heights. Use this chart to determine the correct Duct Cover Accessory for 8-ft. to 10-ft. ceilings that must be ordered with the hood. ZV850SB Installation Heights Actual *Possible Hood Ceiling Height... -
Page 5: Remove Packaging, Check Contents
Installation Preparation REMOVE THE PACKAGING The vent hood is packed separate from the required accessory: ZXR858, ZXR859 or ZXR8510. • Remove the frame, cover, parts box, side bars and packaging. • Remove junction box cover. • Install strain relief onto junction box cover. -
Page 6: Install Ceiling Support
INSTALL CEILING SUPPORT STRUCTURE • At the hood location, install 2 x 4 cross framing between ceiling joists as shown. • The 2 x 4 cross framing can be installed standing or flat. See illustration. Top View of Support Framing 8-3/4"... -
Page 7: Step 2, Install Upper Support Frame
3 INSTALL LOWER SUPPORT FRAME • Insert lower support frame (from required accessory ZXR858, ZXR859 or ZXR8510) into the upper support frame and loosely secure with 8 screws and washers (4 on the front and 4 on the back sides). -
Page 8: Step 4, Secure Wiring
4 SECURE WIRING • Route house wiring through the ceiling hole and pull a length to reach the hood junction box, approximately 6″ below the support. Front Side Support Frames • Tape the wire to the front of the frame support to prevent damage during installation and service. -
Page 9: Step 6, Install Decorative Duct Covers
6 INSTALL DECORATIVE DUCT COVERS Install Screw on Pretap 2 Screw Holes Top Duct Cover • Pretap or drive decorative screw into the screw holes on the support frame. This will make screw installation easier. • Separate the two decorative duct covers. •... -
Page 10: Step 7, Install Hood
7 INSTALL HOOD Align Duct Connector to House Duct Note: TWO PEOPLE ARE REQUIRED TO COMPLETE THIS INSTALLATION! • Lift the hood up to the support frame. Carefully align the hood mounting studs into the support frame holes, and at the same time, guide the hood duct connector into the duct. -
Page 11: Install Utility Bars
9 SLIDE DUCT COVER DOWN, INSTALL SIDE UTILITY BARS • Hold the decorative duct cover and remove the temporary stop screw from the support frame. Return the screw to the service manual envelope for future use. • Slide the lower duct cover down onto the hood. •... - Page 12 Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram 1.800.444.1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Consumer & Industrial GE Appliances General Electric Company Louisville, KY 40225...