hit counter script
Toshiba Rackmount Keyboard DraweraSatellite M30 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. Rackmount Keyboard DraweraSatellite M30
  6. User manual
Toshiba Rackmount Keyboard DraweraSatellite M30 User Manual

Toshiba Rackmount Keyboard DraweraSatellite M30 User Manual

Portable personal computer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Satellite M30
TOSHIBA
Satellite M30
Portable Personal Computer
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba Rackmount Keyboard DraweraSatellite M30

Summary of Contents for Toshiba Rackmount Keyboard DraweraSatellite M30

  • Page 1 Satellite M30 TOSHIBA Satellite M30 Portable Personal Computer User’s Manual...
  • Page 2 User’s Manual Copyright © 2004 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

  • Page 3: Fcc Information

    Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, IEEE1394...
  • Page 4 TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949) 583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: PSM33* conforms to the following Standards: Supplementary “The product complies with the requirements of Information: the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE...

  • Page 5: Region Selection

    User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121. Germany ATAAB AN005,AN006,AN007,AN009,AN010 and DE03,04,05,08,09,12,14,17 Greece ATAAB AN005,AN006 and GR01,02,03,04...

  • Page 6: Type Of Service

    FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.

  • Page 7: Fax Branding

    User’s Manual Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone...
  • Page 8 User’s Manual The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
  • Page 9 User’s Manual Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
  • Page 10 User’s Manual ■ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: ■ a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network.

  • Page 11: Optical Disc Drive Safety Instructions

    User’s Manual The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100. The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications.
  • Page 12 User’s Manual DVD Super Multi UJ-820 ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 13 User’s Manual HITACHI LG DVD-ROM&CD-R/RW GCC-4241N ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■...
  • Page 14 User’s Manual International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.”...
  • Page 15 User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
  • Page 16 User’s Manual User’s Manual...

  • Page 17: Table Of Contents

    Satellite M30 Table of Contents Preface Manual contents ......... xxiii Conventions.
  • Page 18 Table of Contents Optical media drives........2-13 Region codes for DVD drives and media .
  • Page 19 DLA for TOSHIBA ........
  • Page 20 Table of Contents LAN........... . 4-26 LAN cable types .
  • Page 21 Table of Contents TOSHIBA Password Utility ....... . . 6-14 User password.
  • Page 22 TOSHIBA support ........

  • Page 23: Manual Contents

    Satellite M30 Preface Congratulations on your purchase of the Satellite M30 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite M30 computer.

  • Page 24: Conventions

    Preface Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup explains how to configure the computer using the HW Setup program.

  • Page 25: Key Operation

    Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
  • Page 26 Preface xxvi User’s Manual...

  • Page 27: General Precautions

    Satellite M30 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.

  • Page 28: Pc Card Overheating

    For optimum performance, use your computer product only under recommended conditions Read additional restrictions under “Environmental Conditions” in your product Resource Guide. Contact TOSHIBA Service and Support for more information. xxviii...

  • Page 29: Introduction

    Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.

  • Page 30: Software

    If any of the items are missing or damaged, contact your dealer immediately. Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: User’s Manual...
  • Page 31 Introduction Processor Built-in ® The computer is equipped with an Intel processor. ® ® Intel Pentium M processor, which incorporates a 1MB level 2 cache memory. ® It also supports Enhanced Intel SpeedStep technology. ® ® Intel Pentium M processor 1.50 GHz ®...
  • Page 32 Introduction Universal AC The universal AC adaptor provides power to the adaptor system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models.
  • Page 33 Introduction Computers in this series can be configured with an optical media drive. The available optical media drives are described below. DVD-ROM&CD-R/RW Some models are equipped with a full-size, DVD- drive ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.

  • Page 34: Pointing Device

    Introduction Display The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 15.4" TFT screen 16 M colors, with a resolution of 1280 horizontal × 800 vertical pixels WXGA. Graphics controller A 128-bit graphics controller maximizes display performance.
  • Page 35 Introduction Multimedia Sound system Windows sound system compatible sound system provides internal speakers and microphone as well as jacks for an external microphone and headphone. S-Video out port This S-Video port lets you transfer NTSC or PAL data to external devices. Monitor-in port Used for displaying video from your digital camcorder or video recorder on the internal LCD.

  • Page 36: Special Features

    Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
  • Page 37 Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver. System automatic...
  • Page 38 Hibernation and shuts down. You can specify the setting in the Setup Action tab in TOSHIBA Power Saver. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s...

  • Page 39: Utilities

    “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click the Windows Start button, point to All Programs, point to TOSHIBA, point to Utilities and click Fn-esse. DVD Video Player The DVD Video Player is used to play DVD- Video.
  • Page 40 [Start] - [All Programs] - [TOSHIBA] -[Utilities] [PC Diagnostic Tool] TOSHIBA Touch and TOSHIBA Touch and Launch is a tool that allows Launch you to perform various tasks easily using Touch pad. TOSHIBA Touch and Launch is useful in the following conditions.

  • Page 41: Options

    (PC2700 DDR) can easily be installed in the computer. Standard battery An additional battery pack can be purchased pack from your TOSHIBA dealer. Use it as a spare or replacement. Universal AC If you use your computer at more than one site adaptor...
  • Page 42 Introduction 1-14 User’s Manual...

  • Page 43: The Grand Tour

    Satellite M30 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position.

  • Page 44: Left Side

    The Grand Tour Indicators (2) These LEDs let you monitor the DC IN, power and battery status. Details are in the Indicators section. Display latch This latch secures the LCD panel in its closed position. Slide the latch to open the display. Wireless This switch turns the Wireless functions on and Communication...
  • Page 45 The Grand Tour Universal The Universal Serial Bus port is on the left side. The port comply with the USB 2.0 standard, Serial Bus which enables data transfer speeds 40 times (USB 2.0) port faster than the USB 1.1 standard (The ports also support USB 1.1.).

  • Page 46: Right Side

    The Grand Tour Right side Figure 2-3 shows the computer’s right side. Microphone jack Headphone jack USB ports Optical media drive USB port Figure 2-3 The right side of the computer Headphone jack This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum).

  • Page 47: Backside

    The Grand Tour Backside Figure 2-4 shows the computer’s back panel. External monitor port Link indicator LAN active LAN jack (green) indicator (orange) Modem jack Battery pack DC IN 15V Figure 2-4 The backside of the computer LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 Ether megabits per second, 10BASE-T), Fast Ethernet...

  • Page 48: Underside

    The Grand Tour DC IN 15V The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage DC IN 15V your computer. Modem jack In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line.

  • Page 49: Front With The Display Open

    The Grand Tour Memory module This cover protects one memory module sockets cover one or no module is preinstalled. Another memory module is under the keyboard. Refer to Memory expansion section in Chapter 8, Optional Devices. Battery release Slide and hold this latch to release the battery pack for removal.
  • Page 50 The Grand Tour Display hinge The display hinge holds the display screen at easy-to-view angles. Display screen The LCD displays high-contrast text and graphics. The computer’s WXGA screen consists of 1280 × 800 pixels. Refer to Display Controller and Modes in Appendix B.

  • Page 51: Indicators

    The Grand Tour TV-out button Pressing this button while Windows is running will switch the display unit to TV. When Express Media Player is running, this button does nothing. The TV-out button should be programmable under Windows and designed as a utility that allows users to configure options.
  • Page 52 The Grand Tour Power The Power indicator glows green when the computer is on. If you select Standby from Shut Down Windows, this indicator flashes orange (one second on, two seconds off) while the computer shuts down. Battery The Battery indicator shows the condition of the battery’s charge: Blue indicates full charge, orange indicates battery charging and flashing orange indicates a low battery charge.
  • Page 53 The Grand Tour The following indicators show the status of the display overlay. Arrow Mode indicator Numeric Mode indicator Figure 2-9 Keypad overlay indicators Arrow mode When the Arrow mode indicator lights blue, you can use the keypad overlay (gray labeled keys) as cursor keys.

  • Page 54: Usb Floppy Disk Drive

    The Grand Tour USB floppy disk drive A 3 1/2” floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks. It connects to the USB port. Disk-In-Use Floppy disk Indicator Eject button slot Figure 2-10 USB floppy disk drive Disk-In-Use This indicator lights when the floppy disk is being accessed.

  • Page 55: Optical Media Drives

    The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVD- ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs and on the Mode Control buttons refer to the Using optical media drives...

  • Page 56: Dvds

    The Grand Tour DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Formats The drives support the following formats: ■...

  • Page 57: Dvd Super Multi Drive

    The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.

  • Page 58: Universal Ac Adaptor

    Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.

  • Page 59: Getting Started

    Satellite M30 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.

  • Page 60: General Conditions

    Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation.

  • Page 61: Seating And Posture

    Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. Below eye level 90°angles...

  • Page 62: Work Habits

    Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. User’s Manual...

  • Page 63: Opening The Display

    Getting Started 1. Connect the power cord to the AC adaptor. Figure 3-2 Connecting the power cord to the AC adaptor 2. Connect the AC adaptor’s DC output plug to the DC IN 15V input port on the right of the computer. DC IN 15V Figure 3-3 Connecting the adaptor to the computer 3.

  • Page 64: Turning On The Power

    Getting Started Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Display latch Figure 3-4 Opening the display Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system.

  • Page 65: Starting Up For The First Time

    Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen.
  • Page 66 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost.

  • Page 67: Standby Mode

    ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.

  • Page 68: Restarting The Computer

    1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.

  • Page 69: Restoring The Preinstalled Software

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the up or down cursor key to select the CD/DVD-ROM Drive in the Boot Devices menu.
  • Page 70 Getting Started 3-12 User’s Manual...

  • Page 71: Operating Basics

    Satellite M30 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive (optional in some models), optical media drives, Audio/video controls, HVE, Express Media Player, the internal modem, the wireless communication and LAN. It also provides tips on caring for your computer, floppy disks and CD/DVDs.

  • Page 72: Using The Usb Floppy Disk Drive

    Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap the Touch Pad once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material.

  • Page 73: Disconnecting 3 1/2" Floppy Disk Drive

    Operating Basics Disconnecting 3 1/2" floppy disk drive When you have finished using the floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped.

  • Page 74: Loading Discs

    Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the eject button to open the drawer slightly. Eject button Figure 4-3 Pressing the eject button b.
  • Page 75 Operating Basics 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray.

  • Page 76: Removing Discs

    Operating Basics Removing discs To remove the CD/DVD, follow the steps below and refer to figure 4-8. Do not press the eject button while the computer is accessing the media drive. Wait for the Optical media drive indicator to go out before you open the drawer.

  • Page 77: Controls For Cd/Dvd And Digital Audio

    If you want to control the optical media drive by CD/DVD control when the OS is booted up, set the appropriate player application software. You cannot play optical media, only by setting the internal CD/DVD play drive on the Media Apps tab of the TOSHIBA Controls. ■...

  • Page 78: Play/Pause And Stop Buttons

    Operating Basics If Random is selected in Windows Media Player, selecting Next or Previous advances to a random selection. Play/Pause and Stop buttons A single button on a rocker controls the Play/Pause and Stop functions. Press on the icon to select the desired function. Press the icon to begin or pause play.

  • Page 79: Feedback

    Operating Basics Power management 1. Clicked the Advanced tab. 2. Select the Enable Power Management check box. 3. Input a time in Time to Power Saving State. If the Enable Power Management check box is not selected, the audio controller always runs. Figure 4-9 Advanced window Sound quality Adjust the equalizer settings to enhance sound quality.

  • Page 80: Hve(High Quality Video Engine)

    WinDVD and the HVE feature of Express Media Player. Users can select from three video quality modes depending on their preferences for watching videos. A dedicated utility (TOSHIBA Picture Enhancement Utility) running on Windows is developed to allow users to select a mode.

  • Page 81: Restrictions Of The Monitor-In Mode

    Operating Basics Restrictions of the Monitor-in mode ■ Disable the Windows’ Monitor Auto Off feature (this will override the Monitor-in mode). ■ If the Monitor Auto Off is on, the LCD displays nothing even when you click the Monitor-in button to switch to the Monitor-in mode. ■...

  • Page 82: Writing Cds On Dvd-Rom&Cd-R/Rw Drive

    MITSUBISHI CHEMICAL CORPORATION, RICOH Co., Ltd. ■ Ultra-Speed CD-ROM: MITSUBISHI CHEMICAL CORPORATION TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.

  • Page 83: When Writing Or Rewriting

    DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage. Disclaimer TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product.

  • Page 84: Before Writing Or Rewriting

    Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates.
  • Page 85 Operating Basics ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. ■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD- RAM is affected by the quality of the disc and the way it is used.

  • Page 86: When Writing Or Rewriting

    ■ Always copy data from the HDD to the DVD-RAM. Do not use cut-and- paste. The original data will be lost if there is a write error. RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■...

  • Page 87: Data Verification

    Operating Basics ■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/ +RW to CD-R/RW using the “Exact Copy” function of RecordNow!. ■ RecordNow! cannot record in packet format. ■ You might not be able to use the “Exact Copy” function of RecordNow! to back up a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder.

  • Page 88: Dla For Toshiba

    Operating Basics DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable. ■ DLA does not support formatting the DVD-RAM disc and writing to it.

  • Page 89: When Windvd Creator Platinum Is Used

    Operating Basics When WinDVD Creator Platinum is used: You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound is choppy. 1. Click the Windows Start button and select the Control Panel option. 2.

  • Page 90: How To Learn More About Intervideo Windvd Creator

    Operating Basics How to learn more about InterVideo WinDVD Creator Please refer to the on-line Help for additional InterVideo WinDVD Creator information. Important information for use Note the following limitations when you write video DVD: 1. Editing digital video ■ Log in with Administrator rights to use WinDVD Creator.
  • Page 91 Operating Basics ■ Install, remove or connect external devices, including the following: PC card, SD card, USB devices, external display, i.LINK. devices, optical digital devices. ■ Please verify your disc after recording important data. ■ DVD-R/+R/-RW disc cannot be written in VR format. ■...

  • Page 92: Media Care

    Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1.

  • Page 93: Region Selection

    To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 94: Modem Selection

    Operating Basics Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match.

  • Page 95: Disconnecting

    TOSHIBA strongly recommend the customer to enable the WEP function. ■ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. User’s Manual 4-25...

  • Page 96: Wireless Communication Switch

    Operating Basics Wireless communication switch You can enable or disable Wireless LAN function, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the right to turn it on and to the left to turn it off. ■...

  • Page 97: Lan Cable Types

    Operating Basics LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE- TX), be sure to connect with a CAT5 cable.

  • Page 98: Cleaning The Computer

    Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again.

  • Page 99: Heat Dispersal

    CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. Maximum Turns on the fan first, then if necessary, lowers the CPU Performance processing speed.
  • Page 100 Operating Basics 4-30 User’s Manual...

  • Page 101: The Keyboard

    Satellite M30 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with.

  • Page 102: F1 ... F12 Function Keys

    Soft keys: Fn key combinations The Fn (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.

  • Page 103: Hot Keys

    The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to Keypad overlay section in this chapter for more information on how to operate these keys.
  • Page 104 Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the profile item in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification.
  • Page 105 You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. ■ The brightness level is always set at the maximum value for about 18 seconds, when the LCD turns on.

  • Page 106: Fn Sticky Key

    Fn key. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA, point to Utilities and click Accessibility.

  • Page 107: Keypad Overlay

    The Keyboard Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the center of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in figure 5-2.

  • Page 108: Temporarily Using Normal Keyboard (Overlay On)

    The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.

  • Page 109: Power

    Satellite M30 Chapter 6 Power The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a...
  • Page 110 Power Table 6-1 Power conditions continued Power on Power off (no operation) Battery charge • Operates adaptor is above low • LED: Battery off battery trigger DC IN off connected point Battery charge • Operates is below low • LED: Battery battery trigger flashes orange point...

  • Page 111: Power Indicators

    Power Power indicators As shown in the above table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: The battery charge is low.

  • Page 112: Power Indicator

    Power Power indicator Check the Power indicator to determine the power status: Indicates power is being supplied to the computer Blue and the computer is turned on. Indicates power is being supplied to the computer Blinking orange while the computer is in Standby mode. The indicator turns on for one second and off for two seconds.

  • Page 113: Battery Pack

    The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not remove the battery pack while the computer is in Standby mode.Data is stored in RAM, so if the computer loses power it will be...

  • Page 114: Real Time Clock Battery

    0251: CMOS checksum is inconsistent The computer’s RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.
  • Page 115 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. User’s Manual...
  • Page 116 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture.

  • Page 117: Charging The Batteries

    The Battery indicator glows orange when the battery is being charged. Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger.

  • Page 118: Monitoring Battery Capacity

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 119: Maximizing Battery Operating Time

    ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power. This mode has the following options: ■...

  • Page 120: Replacing The Battery Pack

    Power 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged.
  • Page 121 Battery safety lock Battery release latch Battery pack Figure 6-3 Releasing the battery pack For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. User’s Manual 6-13...

  • Page 122: Installing The Battery Pack

    Battery safety lock Battery pack Figure 6-4 Securing the battery pack TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: Start ->...
  • Page 123 If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format. To start the format tool, point to or click the following items: Start ->...

  • Page 124: Supervisor Password

    Register, delete or change the supervisor password. ■ Create or invalidate a supervisor token. This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users.

  • Page 125: Power-Up Modes

    Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver. Hot keys You can use hot keys Fn + F3 to enter Standby mode and Fn + F4 to enter Hibernation.
  • Page 126 Power 6-18 User’s Manual...

  • Page 127: Hw Setup

    Satellite M30 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU and LAN. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup.

  • Page 128: Boot Priority

    *In this computer, CD-ROM refers to the Fixed optical media drive. ■ PC card HDD boot is supported only by slot 0 on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. ■ When you assign a PC card HDD top priority, “PC” is not displayed.
  • Page 129 HW Setup. ■ Support of PC (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. ■ A PC (ATA) card takes the position of HDD in the Boot Priority Options list.
  • Page 130 HW Setup This function lets you set the CPU operating mode. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed Dynamically automatic switching function is enabled. When Switchable the computer is in use, CPU operation is automatically switched when necessary.

  • Page 131: Optional Devices

    Satellite M30 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC cards ■ SD cards ■...

  • Page 132: Pc Cards

    The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards.

  • Page 133: Sd Cards

    Optional Devices 5. Grasp the PC card and draw it out. PC card Eject button Figure 8-2 Removing the PC card SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory.

  • Page 134: Inserting An Sd Card

    Optional Devices Inserting an SD card To insert an SD card, follow the steps below. 1. Insert the SD card. 2. Press gently to ensure a firm connection. SD card Figure 8-3 Inserting an SD card Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below.

  • Page 135: Sd Card Care

    Optional Devices ■ Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card.

  • Page 136: Installing Memory Module

    Optional Devices ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a. The computer is turned on.

  • Page 137: Removing Memory Module

    Optional Devices 5. Fit the memory module’s connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Figure 8-6 Seating the memory module ■ Be careful not to drop the screw inside the computer. ■...

  • Page 138: Battery Packs

    Optional Devices Latches Figure 8-7 Removing the memory module 6. Seat the memory module cover and secure it with one screw. Battery packs You can increase the portability of the computer with additional standard or high-capacity battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery.

  • Page 139: External Monitor

    Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2.

  • Page 140: Changing The Resolution

    There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.

  • Page 141: Connecting

    Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■...
  • Page 142 Optional Devices 8-12 User’s Manual...

  • Page 143: Troubleshooting

    Satellite M30 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 144: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 145: Hardware And System Checklist

    Troubleshooting Software The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.

  • Page 146: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...

  • Page 147: Ac Power

    Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power for more information. Problem Procedure AC adaptor doesn’t Check the connections. Make sure the cord is power the computer firmly connected to the computer and a power (DC IN indicator does...

  • Page 148: Real Time Clock

    If you do not think the battery is at the end of its operating life, see your dealer. Battery doesn’t power Check the power consumption settings in the computer as long TOSHIBA Power Saver utility. Consider using a as expected power saving mode. Real Time Clock The following message is displayed:...

  • Page 149: Password

    Troubleshooting Password For information on setting and using a password and on creating an SD card token, refer to Chapter 6, Power. Problem Procedure Cannot enter or forgot If you cannot remember the password you can password use an SD card token to start the computer. If you did not create an SD card token or cannot use it to start the computer, contact your dealer.

  • Page 150: Hard Disk Drive

    Troubleshooting Hard disk drive Problem Procedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD-ROM is in the optical media drive. Remove drive any diskette and/or CD-ROM and check Boot priority.
  • Page 151 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.

  • Page 152: Dvd Super Multi Drive

    Troubleshooting DVD Super Multi drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access Make sure the drive's drawer is securely closed. Press gently until it clicks into place. a CD/DVD in the drive Open the drawer and make sure the CD/DVD is properly seated.

  • Page 153: Floppy Disk Drive

    Troubleshooting Floppy disk drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. You cannot access the Try another floppy disk.

  • Page 154: Pointing Device

    Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to standby its Pad operation normal shape and try again to move it.

  • Page 155: Usb

    Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3.

  • Page 156: Sound System

    Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Annoying sound is You may be experiencing feedback. Refer to the heard Feedback item in the...

  • Page 157: Modem

    Troubleshooting Modem Refer to Appendix C, AT Commands and Appendix D, S-registers. Problem Procedure Communication Make sure the computer’s internal modem software can’t initialize settings are correct. Refer to Phone and Modem modem Properties in the Control Panel. You can hear a dial If the call is going through a PBX machine, make tone but can’t make a sure the communication application’s tone dial...

  • Page 158: Lan

    Troubleshooting Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN does Make sure the AC adaptor is connected. The not work Wake-up on LAN function consumes power even when the system is off.

  • Page 159: I.link (Ieee1394)

    If problems persist, contact your dealer. TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.

  • Page 160: Where To Write

    Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia Germany & Austria TOSHIBA Australia Pty. Ltd.
  • Page 161 TOSHIBA Information Systems Systems, Inc. (U.K.) Ltd. 9740 Irvine Boulevard TOSHIBA Court Irvine, California 92618 Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL The Rest of Europe TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany User’s Manual 9-19...
  • Page 162 Troubleshooting 9-20 User’s Manual...

  • Page 163: Specifications

    Satellite M30 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.81 kilograms, configured with: 15.4” WXGA, 256MB RAM, 40GB HDD, DVD Super Multi drive, modem, LAN, Wireless LAN, 6 cell battery, Size 360 (w) × 270 (d) × 25.4/35.9(h) millimeters (not including parts that extend beyond the main body) Environmental Requirements...

  • Page 164: Power Requirements

    Specifications Power Requirements Universal AC 100-240 volts AC adaptor 50 or 60 hertz (cycles per second) Computer 15 VDC 4.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command...
  • Page 165 Specifications Communication Data transmission and reception speed 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/ 37333/38666/40000/41333/42666/44000/45333/ 46666/48000/49333/50666/52000/53333/54666/ 56000 bps 2400/4800/7200/9600/12000/14400 bps Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis...
  • Page 166 Specifications User’s Manual...

  • Page 167: Display Controller And Modes

    Satellite M30 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Wide Extended Graphics Array (WXGA) support for the internal LCD and external monitors.
  • Page 168 Display Controller and Modes Table1 Video modes (VGA) Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 0, 1 40 × 25 8 × 8 16 of 256K 16 of 256K Text Characters 2, 3 80 × 25 8 ×...
  • Page 169 Display Controller and Modes Table1 Video modes (VGA) continued Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 320 × 200 8 × 8 16 of 256K 16 of 256K Grph Pels 640 × 200 8 × 8 16 of 256K 16 of 256K Grph...
  • Page 170 Display Controller and Modes Table 2 Video modes (WXGA) Resolution Vertical colors colors frequency (Hz) 640 × 480 256/256K 256/256K 800 × 600 256/256K 256/256K 1024 × 768 256/256K 256/256K 1280 × 800 256/256K 256/256K 1280 × 1024 256/256K 256/256K (Virtual) 1600 ×...
  • Page 171 Display Controller and Modes Table 2 Video modes (WXGA) continued Resolution Vertical colors colors frequency (Hz) 640 × 480 64K/64K 64K/64K 800 × 600 64K/64K 64K/64K 1024 × 768 64K/64K 64K/64K 1280 × 800 64K/64K 64K/64K 1280 × 1024 64K/64K 64K/64K (Virtual) 1600 ×...
  • Page 172 Display Controller and Modes Table 2 Video modes (WXGA) continued Resolution Vertical colors colors frequency (Hz) 640 × 480 16M/16M 16M/16M 800 × 600 16M/16M 16M/16M 1024 × 768 16M/16M 16M/16M 1280 × 800 16M/16M 16M/16M 1280 × 1024 16M/16M 16M/16M (Virtual) 1600 ×...
  • Page 173 Satellite M30 Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
  • Page 174 AT Commands Communication standard setting This command determines the communication standard CCITT or Bell. Selects CCITT V.22 mode when the modem is at 1200 bps. Selects Bell 212A when the modem is at 1200 bps (default). Selects V.21 when the modem is at 300 bps. Selects Bell 103J when the modem is at 300 bps (default).
  • Page 175 AT Commands Result Codes: n=0,1 ERROR Otherwise Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. Modem goes on-hook (default). Modem goes off-hook. Result Codes: n=0,1 ERROR Otherwise Request ID information This command displays product information about the modem.
  • Page 176 AT Commands Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
  • Page 177 AT Commands Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents.
  • Page 178 AT Commands Dial tone detect Disabled:The modem dials a call regardless of whether it detects a dial tone. Enabled:The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds.
  • Page 179 AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory.
  • Page 180 AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
  • Page 181 AT Commands V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5).
  • Page 182 AT Commands Result Codes: n=0,3 ERROR Otherwise C-10 User’s Manual...
  • Page 183 Satellite M30 Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails.
  • Page 184 S-registers Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range:0-225 Default:0 Units:rings AT escape character (user defined) This register determines the ASCII values used for an escape sequence.
  • Page 185 S-registers Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII.
  • Page 186 S-registers Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range:0-255 Default:2 Units:seconds...
  • Page 187 S-registers S37 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8...

  • Page 188: At Command Set Result Codes

    S-registers AT command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description Command executed CONNECT Modem connected to line RING A ring signal has been detected NO CARRIER Modem lost carrier signal, or does not detect carrier signal, or does not detect answer tone...
  • Page 189 S-registers CONNECT 33600 EC* Connection at 33600 bps DELAYED* Delay is in effect for the dialed number BLACKLISTED* Dialed number is blacklisted BLACKLIST FULL* Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression.
  • Page 190 S-registers User’s Manual...
  • Page 191 Satellite M30 Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably.
  • Page 192 V.90 Table E-1 Result codes for a V.90 connection Result code Description CONNECT 32000 EC* Connection at 32000 bps CONNECT 36000 EC* Connection at 36000 bps CONNECT 40000 EC* Connection at 40000 bps CONNECT 44000 EC* Connection at 44000 bps CONNECT 48000 EC* Connection at 48000 bps CONNECT 52000 EC*...
  • Page 193 V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V.42 error control only NoEC No error control protocol...
  • Page 194 V.90 User’s Manual...

  • Page 195: Internal Modem Guide

    Satellite M30 Appendix F Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem The internal modem is preinstalled.
  • Page 196 Internal Modem Guide 5. Pull the guide (plastic tab) toward the direction shown by arrow, then lift the HDD. Be careful not to damage the connector. 6. Remove two screws and remove the modem board. 7. Disconnect the modem cable. 8.

  • Page 197: Card Specifications

    Satellite M30 Appendix G Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications ■ Mini PCI TypeIII Form Factor ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. Compatibility The ‘Wi-Fi CERTIFIED’...
  • Page 198 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 199 Wireless LAN 2462 2467* 2472* *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/ regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■...
  • Page 200 Wireless LAN User’s Manual...

  • Page 201: Ac Power Cord And Connectors

    Satellite M30 Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters...
  • Page 202 AC Power Cord and Connectors France: Switzerland: Germany: United Kingdom: In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.

  • Page 203: Parts Numbers

    Satellite M30 Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, communication and graphics devices. Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label.
  • Page 204 Parts Numbers Communication Graphics DVD-ROM&CD-R/RW RW/DV 802.11b/g NV34M(32MB) DVD Super Multi MAP34(64MB) User’s Manual...
  • Page 205 Satellite M30 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager ASCII: American Standard Code for Information Interchange BIOS: basic input output system CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-Read/Write...
  • Page 206 Glossary FIR: fast infrared HDD: hard disk drive IDE: integrated drive electronics I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory...
  • Page 207 Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements.
  • Page 208 Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate.
  • Page 209 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
  • Page 210 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
  • Page 211 (FDD): An electromechanical device that reads and writes to floppy disks. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
  • Page 212 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
  • Page 213 Glossary K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys.
  • Page 214 Glossary monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions.
  • Page 215 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver Utility: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
  • Page 216 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
  • Page 217 Glossary Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer. VGA: Video Graphics Array is an industry standard video adaptor that lets you run any popular software. volatile memory: Random access memory (RAM) that stores information as long as power is supplied to the computer.
  • Page 218 Glossary Glossary-14 User’s Manual...
  • Page 219 5-5 controller 1-6 AC adaptor 1-4 hinge 2-8 additional 1-13 opening 3-5 connecting 3-4 DLA for TOSHIBA 1-12 4-18 DC IN 15V port 2-6 Documentation list 1-2 ASCII characters 5-8 DVD Super Multi drive 1-5 location 2-4 Battery...
  • Page 220 Index Fn + Ctrl (enhanced keyboard’s simu- lation) 5-3 Keyboard 1-6 Fn + Enter 5-3 emulating keys on enhanced 5-2 Fn + Esc (sound mute) 5-3 F1 ... F12 function keys 5-2 Fn + F1 (instant security) 5-4 hot keys 5-3 Fn + F2 (power save mode) 5-4 typewriter keys 5-1 Fn + F3 (standby) 5-4...
  • Page 221 6-14 Real Time Clock 9-6 PC card 1-6 Self test 9-4 inserting 8-2 Sound system 9-14 location of slot 2-2 Support from TOSHIBA 9-17 removing 8-2 System start-up 9-3 Ports 1-6 USB 9-13 external monitor 1-6 Wireless LAN 9-16 i.LINK 1-6...
  • Page 222 Index Standby 1-10 setting 3-9 System automatic 1-9 TOSHIBA PC DiagnosticTool 1-12 TOSHIBA Power Saver 1-11 TOSHIBA Utilities 1-8 TOSHIBA Zooming Utility 1-12 Touch Pad 1-6 location 2-7 using 4-1 TV 8-9 USB 1-6 location 2-2 Video modes B-1 Video RAM 1-3...

This manual is also suitable for:

Satellite m30

Table of Contents