Toro 38183 Operator's Manual
Hide thumbs
Also See for 38183:
- Operator's manual (20 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (20 pages)
Table of Contents
Advertisement
Quick Links
CCR Powerlite 325
Snowthrower
Model No. 38183—Serial No. 240000001 and Up
Introduction
Read this manual carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for
operating the product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. The
illustration below identifies the location of the model
and serial numbers on the product. Write the numbers
in the space provided below:
Model #:
Serial #:
This manual uses 2 words to highlight information.
Important: calls attention to special mechanical
information and Note: emphasizes general
information worthy of special attention.
Safety
Read and understand the contents of this manual
before the engine is ever started.
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol
to avoid possible injury or death.
Improperly using or maintaining this
snowthrower could result in injury or death. To
reduce this potential, comply with the following
safety instructions.
The following instructions have been adapted from
the ANSI/OPEI standard B71.3–1995 and the ISO
8437:1989 standard.
2003—The Toro Company
8111 Lyndale Ave., Bloomington, MN 55420, USA
Training
Read the operator's manual carefully. Be
thoroughly familiar with the controls and the
proper use of the equipment. Know how to stop
the unit and disengage the controls quickly.
Never allow children to operate the snowthrower.
Never allow adults to operate the snowthrower
without proper instruction.
Keep the area of operation clear of all persons
(particularly small children) and pets.
Exercise caution to avoid slipping or falling.
Preparation
Thoroughly inspect the area where you will use
the snowthrower. Remove all doormats, sleds,
boards, wires, and other foreign objects.
Release the control bar to disengage the rotor
blades before starting the engine.
Do not operate the snowthrower without wearing
2121
adequate winter garments. Wear footwear that
will improve your footing on slippery surfaces.
Handle fuel with care; it is highly flammable.
– Use an approved fuel container.
– Never add fuel to a running or hot engine.
– Fill the fuel tank outdoors with extreme care.
Never fill the fuel tank indoors.
– Replace the fuel tank cap securely and wipe up
any spilled fuel.
Use only the power cord supplied with the
snowthrower and a receptacle appropriate for use
with the power cord for electric-start motors.
Never attempt to make any adjustments while the
engine is running, except where specifically
recommended by Toro.
Let the engine and the snowthrower adjust to the
outdoor temperature before starting to clear
snow.
Operating any powered machine can result in
foreign objects being thrown into the eyes.
Always wear safety glasses or eye shields while
operating, adjusting, or repairing the
snowthrower.
Printed in the USA
All Rights Reserved
Register your product at www.Toro.com
Form No. 3329-446 Rev A
Operator's Manual
Original Instructions (GB)
Advertisement
Table of Contents
Related Manuals for Toro 38183
Summary of Contents for Toro 38183
- Page 1 (particularly small children) and pets. additional information, contact an Authorized Service Exercise caution to avoid slipping or falling. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. The Preparation illustration below identifies the location of the model and serial numbers on the product.
-
Page 2: Toro Snowthrower Safety
Stop the engine whenever you leave the The following list contains safety information specific operating position, before unclogging the to Toro products or other safety information that you discharge chute, and when making any repairs, must know. adjustments, or inspections. -
Page 3: Sound Pressure
Store fuel in an approved fuel container. Remove the key from the ignition switch before storing the snowthrower. Purchase only genuine Toro replacement parts and accessories. Sound Pressure This unit has a maximum sound pressure level at the operator’s ear of 90 dBA, based on measurements of... -
Page 4: Safety/Instruction Decals
Safety/Instruction Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 94-2562 94-2560 1. Cutting/dismemberment hazard, auger—stay away from moving 1. Cutting/dismemberment hazard, impeller—stay away from parts; remove the key and read the instructions before servicing moving parts;... -
Page 5: Product Overview
Product Overview Setup Installing the Handle 1. Position the ends of the upper handle on the inside of the lower handle and align the holes. 2. Insert the oval-head bolts into the aligned holes, with the bolt heads on the outside of the handle. -
Page 6: Installing The Control Cable
This snowthrower uses a 50:1 gasoline-to-oil mixture. 4. Slide the spring cover (A) over the spring and the Use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added) cable adjuster and push the spring end through the or an equivalent high-grade, NMMA TCW-certified hole at the end of the spring cover. -
Page 7: Filling The Fuel Tank
Filling the Fuel Tank Operation Fill the fuel tank with a fresh gasoline-and-oil mixture Note: Determine the left and right sides of the mixed at the proper ratio. machine from the normal operating position. Starting the Engine 1. Turn the ignition key clockwise to the On position. 2. -
Page 8: Stopping The Engine
Stopping the Engine Throwing Snow To stop the engine, turn the key counterclockwise to the Off position. The rotor blades can throw stones, toys, and Starting the Rotor Blades other foreign objects and cause serious personal injury to the operator or to bystanders. To start the rotor blades, hold the control bar against the handle. -
Page 9: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval Check for loose fasteners and tighten them if necessary. Initially Check the control cable and adjust it if necessary. Check the control cable and adjust it if necessary. -
Page 10: Adjusting The Control Cable
Adjusting the Control Cable Inspecting the Rotor Blades 1. Stop the engine and wait for all moving parts to stop. Before each season, inspect the rotor blades for 2. Move the control bar toward the handle to remove wear. When a rotor blade edge has worn down to the the slack in the control cable. -
Page 11: Storing The Snowthrower
1. Add a fuel stabilizer/conditioner to the fuel in the fuel tank as directed. Note: If you use Toro 50:1 2-Cycle Oil (Fuel Stabilizer Added), you do not need to add a fuel stabilizer/conditioner. 2. Run the engine for 5 minutes to distribute the conditioned fuel through the fuel system.