Related Manuals for Toro CCR Powerlite 38170
Summary of Contents for Toro CCR Powerlite 38170
- Page 1 FORM NO. 3319–421 CCR POWERLITE SNOWTHROWER Model No. 38170 – 8900001 & Up Model No. 38175 – 8900001 & Up Operator’s Manual...
- Page 2 WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
- Page 3 3. Add remaining amount of 4. Washer 1. Discharge chute gasoline gasoline 2. Chute handle 5. Locknut 2. Install cap and shake can 3. Hex bolt 6. Knob to mix The Toro Company – 1997 Printed in USA All Rights Reserved...
- Page 4 1. Discharge chute 3. Handle 2. Discharge chute handle 1. Key switch 5. Elec. start button* 2. Primer 6. Cord connection* 3. Recoil start ELEC. START MODEL 4. Choke lever 1. Wear indicator hole 1. Chute handle 3. Deflector mounting nuts 2.
- Page 5 1. Torx screw 3. Locknut 5. Drive belt cover 7. Thin layer 2. Capscrew 4. Blade support 6. Thick layer 8. Wear indicator hole 1. Scraper 2. Wear indicator groove 1. Scraper 2. Screws...
- Page 6 1. Self tapping screws 2. Capscrew, nut, washer 1. Idler pulley 3. Notch 2. Idler spring 1. Rotor pulley 3. Idler pulley 1. Control panel 2. Screws 2. Drive pulley 4. Drive belt...
- Page 7 0.030” (.76 mm) 1. Spark plug wire...
-
Page 8: Table Of Contents
All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your CAUTION signals a hazard that may cause minor or... -
Page 9: Safety
Safety Wear adequate winter clothing and rubber boots that will ensure proper footing on slippery surfaces. Do not wear loose fitting clothing that To ensure maximum safety, best performance, and could possibly get caught in moving parts. to gain knowledge of the product, it is essential that you or any other operator of the snowthrower Always wear safety glasses or eye shields during read and understand the contents of this manual... - Page 10 13. Operate the snowthrower only when there is 23. Before adjusting, cleaning, repairing or good visibility or light. inspecting the snowthrower, or before unclogging the discharge chute or impeller 14. Always maintain secure footing and balance and housing, stop engine by turning key to OFF and keep a firm grip on the handle.
- Page 11 33. To assure optimum performance and safety, accidental starting. If major repairs are ever purchase genuine TORO replacement parts and needed, contact your local Authorized TORO accessories to keep your TORO all TORO. Service Dealer for assistance. NEVER USE “WILL FIT” REPLACEMENT PARTS AND ACCESSORIES.
-
Page 12: Symbol Glossary
Ignition off chute Cutting or entanglement of foot – Ignition on rotating auger Shut off engine and remove key before leaving operator 110 volt starter position – single stage snowthrower 50:1 ratio unleaded Hot surface gasoline to TORO 2–cycle oil Choke... -
Page 13: Assembly
Assembly Before Starting Note: Determine left and right sides of snowthrower by standing in the normal operating position. POTENTIAL HAZARD In certain conditions gasoline is extremely Install Discharge Chute (Fig. 2) flammable and highly explosive. WHAT CAN HAPPEN Position holes on sides of discharge chute over A fire or explosion from gasoline can burn hex bolts on sides of chute handle. - Page 14 OR WHITE GAS BECAUSE ENGINE engine performance, mix the contents of one 5.2 FUEL SYSTEM DAMAGE COULD ounce bottle of Toro 50:1 Two–Cycle Oil with RESULT. two gallons of fresh, unleaded regular gasoline. You can also use Toro “Easy Mix” Two–Cycle DO NOT USE FUEL ADDITIVES OTHER Oil (3.2 ounce bottle mixed one per gallon of...
-
Page 15: Operation
If engine still will not start after a second attempt, bring the (Fig. 5) snowthrower to an Authorized Toro Service Dealer for servicing. CONTROLS—Key switch, primer, electric start button*, and recoil starter are located on the When engine starts, move choke lever to middle control panel. -
Page 16: Folding Snowthrower
rotor blades strike the ground. The wheels do not CONTROLS. When any control or part have to touch the ground in order to self-propel. becomes hard to operate, start the engine and let The further you tilt the handle forward, the faster it run for a few minutes. -
Page 17: Maintenance
After fuel is drained, start engine and let it run until all fuel is consumed and engine stops. Repeat the starting procedure two more times to POTENTIAL HAZARD assure all fuel is removed from the engine. Gasoline and its fumes are highly Note: This is the only procedure flammable, explosive, and dangerous if... -
Page 18: Replacing Scraper
side (Fig. 9). If one of the blades is installed REMOVING BELT (Fig. 13)—Pull idler pulley with the thick layer on the outside of the curve up slightly while pulling out on belt. Allow and the other blade installed with the thick layer pulley to gradually release when it can move on the inside of the curve, the blades will be past the belt. -
Page 19: Storage
TIGHTEN FASTENERS AND Add Toro Stabilizer/Conditioner to the fuel tank CLEAN—Tighten screws, bolts, knobs and nuts (one ounce per gallon of fuel). if necessary. Repair or replace damaged parts.