Table of Contents
Advertisement
3/8" DRILL DRIVER KIT
14.4 VOLT
95094
OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INjURy, READ
AND UNDERSTAND ALL WARNINGS AND
INSTRUCTIONS bEfORE USE.
Copyright
2006 by Harbor Freight Tools
. All rights reserved. No portion of
©
®
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
for technical questions or replacement parts, please call 1-800-444-3353.
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools 95094
Summary of Contents for Harbor Freight Tools 95094
-
Page 1: Operating Instructions
. All rights reserved. No portion of © ® this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. for technical questions or replacement parts, please call 1-800-444-3353. -
Page 2: Product Specifications
Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly for technical questions, please call 1-800-444-3353. SKU 95094 14.4 VDC NiCd Battery 3 to 5 Hours 120 VAC / 60 Hz;... -
Page 3: Personal Safety
Always wear ANSI-approved safety goggles when working with this tool. for technical questions, please call 1-800-444-3353. SKU 95094 eliminates the need for the three wire grounded Personal Safety... - Page 4 Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep drill bits sharp and clean. Properly maintained accessories with a sharp cutting edge are less likely to bind and are easier to con- trol.
-
Page 5: Specific Safety Rules
Maintain labels and nameplates on the Cordless Drill. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replace- ment. When using the Cordless Drill, always maintain a firm grip on the tool with both hands. -
Page 6: Grounded Tools: Tools With Three Prong Plugs
The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See figure A.) for technical questions, please call 1-800-444-3353. SKU 95094 GROUNDING WARNING! PAGE 6... -
Page 7: Double Insulated Tools: Tools With Two Prong Plugs
If you are using one extension cord for more than one tool, add the nameplate am- peres and use the sum to determine the required minimum cord size. (See figure C.) for technical questions, please call 1-800-444-3353. SKU 95094 ExTENSION CORDS fIGURE b PAGE ... - Page 8 C * based on limiting the line voltage drop to five volts at 150% of the rated amperes. n 0 xxxx/min. for technical questions, please call 1-800-444-3353. SKU 95094 (120 OR 240 VOLT) ExTENSION CORD LENGTH 50 feet 75 feet...
- Page 9 When unpacking, check to make sure that the product is complete and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. NOTE: The Battery Pack (23) requires charging. The first charge requires 5 hours charge time prior to using the Cordless Drill.
- Page 10 RING (3) bATTERy PACK (23) To install a drill/screwdriver bit, with the chuck pointing away from you, hold the Chuck Sleeve firmly in place and turn the Chuck (1) counterclockwise. Insert the shank of the bit all the way into the Chuck (1). While holding the Chuck Sleeve in place, turn the Chuck clockwise to lock the bit in place.
- Page 11 When drilling in light gauge metal or wood, use a wooden block to back up the material to prevent damage to the workpiece. Mark the center of the hole to be drilled with a center punch to give a Drill Bit a start and to prevent it from “walking”.
-
Page 12: Inspection, Maintenance, And Cleaning
Do not use damaged equipment. DAILy: With a soft brush or cloth, remove all dirt and debris from the Cordless Drill. Do not immerse the Cordless Drill in any liquids. If the battery needs replacement keep in mind that the Nickel-Cadmium (Ni- Cd) battery in this tool must be recycled or disposed of properly. -
Page 13: Parts List
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF RE- PLACEMENT PARTS THERETO. for technical questions, please call 1-800-444-3353. SKU 95094 PARTS LIST Q’ty Part... -
Page 14: Assembly Diagram
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. for technical questions, please call 1-800-444-3353. SKU 95094 PAGE 14...