Husqvarna 150BT Operator's Manual
Husqvarna blower operator's manual
Hide thumbs
Also See for 150BT:
- Operator's manual (70 pages) ,
- Operator's manual (18 pages) ,
- Operator's manual (54 pages)
Related Manuals for Husqvarna 150BT
Summary of Contents for Husqvarna 150BT
- Page 1 WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. APPLICABLE SERIAL NUMBERS: 80100101 and up Operator’s manual 130BT 150BT 170BT 180BT English 115 09 83-26...
- Page 2 (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the blowers Husqvarna 150BT with serial numbers dating 2007 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...
- Page 3 (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the blowers Husqvarna 170BT with serial numbers dating 2006 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...
-
Page 4: Table Of Contents
WAIST BELT [150BT] [170BT] [180BT]........ -
Page 5: Safety
• Approved eye protection This product is in accordance with applicable EC directives. Always wear protective gloves. The blower can forcibly throw objects that can bounce back. This can result in serious eye injuries if the recommended safety equipment is not used. -
Page 6: Symbols On The Machine
It is extremely important that you read and understand the contents of this Operator’s manual. 10. Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. -
Page 7: Working Conditions
WORKING CONDITIONS 1. Refrain from operating the blower if you are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. To reduce the risk of hearing loss associated with sound levels, hearing protection is required. -
Page 8: Before Starting The Engine
If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been repaired. -
Page 9: Maintenance
Improper service to the blower fan and muffler could cause a hazardous failure. 5. When replacing the any other part or any lubricant, always be sure to use only Husqvarna products or products which have been certified by Husqvarna for use with the Husqvarna product. -
Page 10: Parts View
English <130BT> 1. Frame 2. Harness 3. Spark Plug Cap 4. Throttle Lever 5. Guard Net 6. Choke Lever 7. Air Cleaner 8. Volute Case, Cover 9. “CAUTION” Label 10. Elbow 11. Fuel Tank 12. Recoil Starter DISPOSAL When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. Frame: Harness: Throttle lever:... - Page 11 <150BT> 1. Frame 2. Harness 3. Spark Plug Cap 4. Throttle Lever 5. Net 6. Choke Lever 7. Air Cleaner 8. Volute Case, Cover 9. “CAUTION” Label 10. Elbow 11. Fuel Tank DISPOSAL When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations.
- Page 12 English <170BT> 1. Frame 2. Harness 3. Spark Plug Cap 4. Throttle Lever 5. Net 6. Choke Lever 7. Air Cleaner 8. Volute Case, Cover 9. “CAUTION” Label 10. Elbow 11. Fuel Tank DISPOSAL When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. Frame: Harness: Throttle lever:...
- Page 13 <180BT> 1. Frame 2. Harness 3. Spark Plug Cap 4. Throttle Lever 5. Net 6. Choke Lever 7. Air Cleaner 8. Volute Case, Cover 9. “CAUTION” Label 10. Elbow 11. Fuel Tank DISPOSAL When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. Frame: Harness: Throttle lever:...
-
Page 14: Technical Data
Vibration level at max, speed, right handle prEN15503 (ISO7916) m/s The data shown above are those in the case of one straight pipe. • Specifications are subject to change without notice. • Technical data 130BT 150BT 295x387x432 351x446x479 (11.6x15.2x17) (13.8x17.6x18) 6.75 (14.9) 10.2 (22.5) 0.9 (30.4) 1.25 (42.3) -
Page 15: Assembly
SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. NOTE A light lubricant may be used to ease assembly of flexible hose to blower tube. -
Page 16: Harness
Place the waist belt over your waist and not too far down on the stomach. Tighten the waist belt strap so that you feel the weight of the blower resting on your hip. • Be sure to always tighten the buckle in front of your body. -
Page 17: Fuel
• The engines are lubricated by oil specially formulated for air- cooled 2-cycle gasoline engine use. If Husqvarna oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) •... -
Page 18: Operation
(2) About 1/3 Open (3) Idling (4) STOP 4. To start, hold the top of the blower firmly with your left hand. Pull the starter knob slowly until you feel it engage and then give it a vigorous strong pull. IMPORTANT •... -
Page 19: Adjusting Idle Speed
(1) Idling Adjustment Screw [150BT] [170BT] [180BT] • The idling speed is set for 2200 rpm [150BT] or 2000 rpm [170BT/180BT] at the factory. If it is necessary to adjust the idle speed, use the adjustment screw on the top side of carburetor. -
Page 20: Maintenance
A clogged air filter may increase fuel consumption while cutting down the engine power. • Never operate the blower without an air filter or with a deformed or broken filter element because unfiltered dusty air will quickly ruin the engine. -
Page 21: Fuel Filter
WARNING • Periodically inspect the muffler for loose fasteners, damage or corrosion. If any sign of exhaust leakage is found, do not use the blower and have it repaired immediately. 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. -
Page 22: Air Inlet Net
(1) Net WARNING Never use the blower without the net on the blower. Before each use, check that the net is attached in place and is free from any damage. IGNITION COIL AIR GAP INSPECTION • If the gap is not accurate or when installing the coil or rotor, adjust the air gap between the ignition coil and the iron core of the rotor.