hit counter script

Write Stream Dma (3Ah) - Hitachi Deskstar 7K500 Specifications

3.5 inch serial ata hard disk drive
Hide thumbs Also See for Deskstar 7K500:
Table of Contents

Advertisement

5.56 Write Stream DMA (3Ah)

Table 116: Write Stream DMA Command (3Ah)
Command Block Output Registers
Register
Data Low
Data High
Feature
Current
Previous
Sector
Current
Count
Previous
Sector
Current
Number
Previous
Cylinder
Current
Low
Previous
Cylinder
Current
High
Previous
Device/Head
Command
Error Register
7
6
5
CRC UNC
0
V
V
0
The Write Stream DMA command allows the host to write data using the DMA data transfer protocol. This com-
mand allows for the host to specify to the device that additional actions need to be performed prior to the comple-
tion of the command if the required bits are set.
If the Write Continuous bit is set to one, the device shall not stop execution of the command due to errors. If the
WC bit is set to one and errors occur in the transfer or writing of the data, the device shall continue to transfer the
amount of data requested and then provide ending status with the BSY bit cleared to zero, the SE bit set to one, the
ERR bit cleared to zero, and the type of error, ICRC, IDNF, or ABRT, reported in the error log. If the WC bit is set
to one and the Command Completion Time Limit expires, the device shall stop execution of the command and pro-
vide ending status with BSY bit cleared to zero, the SE bit set to one, the ERR bit cleared to zero, and report the
fact that the Command Completion Time Limit expired by setting the CCTO bit in the error log to one, In all cases,
the device shall attempt to transfer the amount of data requested within the Command Completion Time Limit
event if some data transferred is in error.
Output Parameters To The Device
Feature Current
URG (bit7)
7 6 5 4 3 2 1 0
- - - - - - - -
- - - - - - - -
V V V V - V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
V V V V V V V V
1 1 1 D - - - -
0 0 1 1 1 0 1 0
4
3
2
1
IDN
0
ABT T0N AMN
V
0
V
0
URG specifies an urgent transfer request. The Urgent bit specifies that the
command should be completed in the minimum possible time by the device and
shall be completed within the specified Command Completion Time Limit.
Deskstar 7K500 Hard Disk Drive Serial ATA Addendum
Command Block Input Registers
Register
Data Low
Data High
Error
Sector
Count
Sector
Number
Cylinder
Low
Cylinder
High
Device/Head
Status
0
7
6
BSY RDY DF DSC DRQ
V
0
V
171
7 6 5 4 3 2 1 0
- - - - - - - -
- - - - - - - -
See below
HOB=0
- - - - - - - -
HOB=1
- - - - - - - -
HOB=0
V V V V V V V V
HOB=1
V V V V V V V V
HOB=0
V V V V V V V V
HOB=1
V V V V V V V V
HOB=0
V V V V V V V V
HOB=1
V V V V V V V V
- - - - - - - -
See below ...
Status Register
5
4
3
2
COR IDX
V
V
-
0
1
0
ERR
-
V

Advertisement

Table of Contents
loading

This manual is also suitable for:

Hds725050kla360

Table of Contents