Page 1: Hard Disk Drive Specifications
Hitachi Global Storage Technologies Hard disk drive specifications Hitachi Deskstar 7K1000.B Hitachi CinemaStar 7K1000.B Hitachi Deskstar E7K1000 3.5 inch Serial ATA hard disk drive Models: HDT721016SLA380 HCT721016SLA380 HDE721050SLA330 HDT721025SLA380 HCT721025SLA380 HDE721064SLA330 HDT721025SLA360 HCT721032SLA380 HDE721075SLA330 HDT721032SLA380 HCT721050SLA380 HDE721010SLA330 HDT721032SLA360 HCT721064SLA380 HDT721050SLA380...
Page 2 Technologies products (machines and programs), programming, or services that are not announced in your country. Such references or information must not be construed to mean that Hitachi Global Storage Technologies intends to announce such Hitachi Global Storage Technologies products, programming, or services in your country.
Page 3: Table Of Contents
Sector Number Register ......................... 51 8.12 Status Register ..........................52 8.13 General Operation Descriptions ........................54 Reset Response ..........................54 Diagnostic and Reset considerations..................... 55 Sector Addressing Mode ......................... 56 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 4 Read Stream DMA (2Ah) ......................168 11.25 Read Stream PIO (2Bh) ......................171 11.26 Read Verify Sector(s) (40h/41h)....................174 11.27 Read Verify Sector(s) Ext (42h) ....................176 11.28 Recalibrate (1xh) ........................178 11.29 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 5 Write Sector(s) Ext (34h) ......................245 11.55 Write Stream DMA (3Ah) ......................247 11.56 Write Stream PIO (3Bh) ......................250 11.57 Write Uncorrectable Ext (45h) ....................253 11.58 12.0 Timings ................................256 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 6 Table 48 Output Registers of SCT Command Using Write Log Ext ............85 Table 49 Key Sector Format ........................86 Table 50 SCT Action Code List ........................ 86 Table 51 Extended Status Code ......................87 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 7 Table 102 Log Address Definition ......................146 Table 103 General Purpose Log Directory .................... 147 Table 104 Extended Comprehensive SMART Error Log ..............148 Table 105 Extended Error log data structure ..................149 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 8 Table 156 SMART Log Directory ......................216 Table 157 SMART summary error log sector ..................217 Table 158 Error log data structure ......................218 Table 159 Command data structure ...................... 218 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 9 Table 179 Write Stream PIO Command (3Bh) ................... 250 Table 180 Write Uncorrectable Ext Command (45h) ................. 253 Table 181 Timeout Values ........................256 Table 182 Timeout Values --Continued-- ....................257 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification viii...
Page 10 Figure 10 Usual Operation ........................... 63 Figure 11 Password Lost ..........................64 Figure 12 Seek overlap ........................... 69 Figure 13 Device address map before and after Set Feature ................73 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 11 General 1.1 Introduction This document describes the specifications of the Deskstar 7K1000.B , Cinemastar 7K1000.B and Deskstar E7K1000, an Hitachi Global Storage Technologies 3.5-inch 7200-rpm ATA interface hard disk drive with the following model numbers:  Deskstar models  HDT721016SLA380 (160GB) ...
Page 12: Glossary
ESD protective bag are the responsibility of the user. 1.4 References ・ Serial ATA II: Extensions to Serial ATA 1.0 ・ Serial ATA International Organization: Serial ATA Revision 2.60 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 13: Table 2 Formatted Capacity
 S.M.A.R.T. (Self Monitoring and Analysis Reporting Technology)  Support security feature  Quiet Seek mode (AAM)  48 bit addressing feature  Adaptive Zone Formatting  SATA 2.6 compliant HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 14: Table 4 Formatted Capacity --Continued
Part 1. Functional specification HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 15: Table 6 Mechanical Positioning Performance
The actuator assembly is balanced to allow vertical or horizontal mounting without adjustment. When the drive is powered off, the actuator automatically moves the head to the actuator ramp outside of the disk where it parks. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 16: Table 8 Command Overhead
Number of Disks Logical Layout Number of Heads Number of Sectors/ Track Number of Cylinders 16,383 Number of Sectors 625,142,448 Total Logical Data Bytes 320,072,933,376 Table 2 Formatted capacity --Continued-- HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 17: Table 9 Mechanical Positioning Performance
The Logical layout to Physical layout (that is, the actual Head and Sectors) translation is done automatically in the drive. The default setting can be obtained by issuing an IDENTIFY DEVICE command HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 18: Table 11 Single Track Seek Time
This cylinder contains the user data which can be sent and retrieved via read/write commands and a spare area for reassigned data. Spare cylinder The spare cylinder is used by Hitachi Global Storage Technologies manufacturing and includes data sent from a defect location. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 19: Table 14 Mode Transition Times
Read (Cache hit) (from Command Write to DRQ) Write (from Command Write to DRQ) 0.015 Seek (from Command Write to Seek Start) not applicable Table 7 Command overhead HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 20: Command Type 1D 2D/3D
Table 9 Full stroke seek time Full stroke seek is measured as the average of 1000 full stroke seeks with a random head switch from both directions (inward and outward). HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 21: Read (Quiet Seek Mode)
This includes the time required for the internal self diagnostics. Note: Max Power On to ready time is the maximum time period that Device 0 waits for Device 1 to assert PDIAG–. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 22: Write (Quiet Seek Mode)
Note: The command is processed immediately but there will be an actual spin down time reflecting the seconds passed until the spindle motor stops. Table 13 Mode transition times HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 23: Figure 1 Plist Physical Format
Figure 1 PList physical format Defects are skipped without any constraint, such as track or cylinder boundary. The calculation from LBA to physical is done automatically by internal table. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 24: Electrical Interface
SATA Figure 2 Connector location (2 and 3 disk model shown) 6.1.1.1 signal connector The SATA signal connector is a 8-pin connector. Power connector is a 15-pin connector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 25: Table 15 Interface Connector Pins And I/O Signals
ATA cable. 6.1.2.4 12V PRECHARGE +12 Vdc power that is available on the extended pins. This is used for pre-charging the 12V circuitry in the I/O Option slot module. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 26 The enclosure shall provide for a current limit of 4.5 A peak on each 5V pre-charge pin (R=1.1 Ohms).These signals are the inbound high-speed differential signals that are connected to the serial ATA cable. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 27: Table 16 Parameter Descriptions
C O M W A KE Figure 3 the timing of COMRESET, COMINIT and COMWAKE PARAMETER DESCRIPTION Nominal (ns) ALINE primitives 106.7 Spacing ALIGN primitives 106.7 Psacing 106.7 Table 15 Parameter descriptions HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 28: Table 17 Temperature And Humidity
Lower duty cycle AV streaming application usage: 70°C max (CinemaStar only) Other application usage : 65°C max 2. Non condensing conditions should be maintained at any time. 3. Maximum storage period within shipping package is one year, HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 29: Figure 4 Limits Of Temperature And Humidity
The drive shows no sign of corrosion inside and outside of the hard disk assembly and is functional after being subjected to seven days at 50°C with 90% relative humidity. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 30: Table 18 Input Voltage
Power supply current of 3 Disk SATA models  Except for a peak of less than 100 s duration Random R/W : 40 IOPS / 16 Blocks Random Write and Random Read HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 31: Table 20 Power Supply Current Of 2 Disk Sata Models
Power supply current of 1 Disk SATA models  Except for a peak of less than 100 s duration Random R/W : 40 IOPS / 16 Blocks Random Write and Random Read HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 32: Table 22 Power Supply Generated Ripple At Drive Power Connector
±300 millivolts peak to peak level difference to the ground of the drive power connector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 33: Data Integrity
Step 2: Wait until the Command Complete status is returned. In a typical case 350 ms are required for the command to finish completion; however, the BIOS time out value needs to be 30 seconds considering error recovery time. Step 3: Terminate power to HDD. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 34: Figure 5 Top And Side Views With Breather Hole Location And Mechanical Dimensions
Mechanical specifications 6.5.1 Physical dimensions Figure 5 Top and side views with breather hole location and mechanical dimensions All dimensions are in millimeters. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 35: Figure 6 Bottom And Side Views With Mounting Hole Locations
All dimensions in the above figure are in millimeters. The breather hole must be kept uncovered in order to keep the air pressure inside of the disk enclosure equal to external air pressure. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 36: Table 23 Physical Dimensions
I/F Connector Bottom View (4X) Max. penetration 4.0 mm Thread 6-32UNC 41.28±0.5 44.45±0.2 95.25±0.2 6.35±0.2 28.5±0.5 60.0±0.2 41.6±0.2 Figure 7 Mounting hole locations (all dimensions are in mm) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 37: Figure 8 Connector Locations
6.5.3 Connector locations Figure 8 Connector locations HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 38: Drive Mounting
Heads are moved out from disks (unload) to protect the disk data during shipping, moving, or storage. Upon power down, the heads are automatically unloaded from disk area and the locking mechanism of the head actuator will secure the heads in unload position. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 39: Table 24 Random Vibration Psd Profile Break Points (Operating)
10 minutes per axis. The PSD levels for the test simulate the shipping and relocation environment shown below. The overall RMS (Root Mean Square) level of vibration is 1.04 G. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 40: Table 25 Random Vibration Psd Profile Break Points (Nonoperating)
The shape is approximately half-sine pulse. The figure below shows the maximum acceleration level and duration. Models Accleration level (G) Duration (ms) 1D/2D models 3D model All models Table 25 Sinusoidal shock wave HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 41: Table 27 Rotational Shock
6.6.5 Nonoperating Rotational shock All shock inputs shall be applied around the actuator pivot axis. Duration Rad/sec 1 ms 30,000 2 ms 20,000 Table 26 Rotational Shock HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 42: Table 28 Sound Power Levels
The seek rate for the drive is to be calculated as shown below:  Dwell time = 0.5 x 60/RPM  Seek rate = 0.4 / (Average seek time + Dwell time) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 43: Identification Labels
The following labels are affixed to every drive shipped from the drive manufacturing location in accordance with the appropriate hard disk drive assembly drawing:  A label containing the Hitachi logo, the Hitachi Global Storage Technologies part number, and the statement “Made by Hitachi Global Storage Technologies Inc.” or Hitachi Global Storage Technologies approved equivalent ...
Page 44: Ul And Csa Standard Conformity
The product complies with the Directive 2002/95/EC of the European Parliament on the restrictions of the use of the certain hazardous substances in electrical and electronic equipment (RoHS). 6.9.6 Secondary circuit protection Spindle/VCM driver module includes 12 V over current protection circuit. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 45: Electromagnetic Compatibility
“Telecommunications Basic Act” and “Radio Waves Act” Korea EMC requirment are based technically on CISPR22:1993-12 measurement standards and limits. MIC standards are likewise based on IEC standards. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 47 Part 2. Interface Specification HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 48: Terminology
Serial ATA II: Extensions to Serial ATA Revision 2.6 Terminology Device Device indicates HDT7210xxSLA3y0 / HCT7210xxSLA3y0 / HDE7210xxSLA3y0. Host Host indicates the system that the device is attached to. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 49: Deviations From Standard
6.5 second. When the specified time limit is shorter than 6.5 second, the issued command is aborted. For HCT7210xxSLA3y0, the minimum time limit is 0.3 second. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 50: Cylinder Low Register
This register contains the low order bits of the starting cylinder address for any disk access. At the end of the command, this register is updated to reflect the current cylinder number. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 51: Table 30 Device Control Register
Interrupt Enable. When -IEN=0, and the device is selected, device interrupts to the host will be enabled. When -IEN=1, or the device is not selected, device interrupts to the host will be disabled. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 52: Table 31 Drive Address Register
-Drive Select 1. Drive select bit for device 1, active low. DS1=0 when device 1 (slave) is selected and active. -DS0 -Drive Select 0. Drive Select bit for device 0, active low. DS0=0 when device 0 (master) is selected and active. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 53: Table 32 Device/Head Register
The head number may be from zero to the number of heads minus one. In LBA mode, HS3 through HS0 contain bits 24-27 of the LBA. At command completion, these bits are updated to reflect the current LBA bits 24-27. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 54: Table 33 Error Register
Track 0 Not Found. T0N=1 indicates track 0 was not found during a Recalibrate command. AMNF (AMN) Address Mark Not Found. This product does not report this error. This bit is always zero. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 55: Features Register
In LBA mode, this register contains Bits 0-7. At the end of the command, this register is updated to reflect the current LBA Bits 0-7. When 48-bit commands are used, the "most recently written" content contains LBA Bits 0-7, and the "previous content" contains Bits 24-31. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 56: Table 34 Status Register
Error. ERR=1 indicates that an error occurred during execution of the previous command. The Error Register should be read to determine the error type. The device sets ERR=0 when the next command is received from the host. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 57 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 58: Table 35 Reset Response
In the case of Sleep mode, the device goes to Standby mode. In other case, the device does not change current mode. (*5) Idle when Power-Up in Standby feature set is disabled. Standby when Power-Up in Standby feature set is enabled. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 59: Table 36 Default Register Values
In each case of Power on Reset, COMRESET, Soft reset, and EXECUTE DEVICE DIAGNOSTIC command, the Table 36 device is diagnosed. And Error register is set as shown in HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 60: Sector Addressing Mode
On LBA addressing mode, the LBA value is set to the following register. Device/Head <--- 27-24 bits Cylinder High <--- 23-16 bits Cylinder Low <--- 15- 8 bits Sector Number <--- 7- 0 bits HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 61: Power Management Feature
If the value of SECTOR COUNT register on Idle command or Standby command is set to 00h, the standby timer is disabled. 9.4.4 Interface Capability for Power Modes Each power mode affects the physical interface as defined in the following table: HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 62: Table 38 Power Conditions
Inactive Table 37 Power conditions Ready (RDY) is not a power condition. A device may post ready at the interface even though the media may not be accessible. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 63: Smart Function
9.5.5 SMART commands The SMART commands provide access to attribute values, attribute thresholds and other logging and reporting information. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 64: Error Log
If interrupted by the host during the self-tests, the device services the host command. If the device receives a firmware modification, all self-test log data is discarded. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 65: Security Mode Feature Set
When the device lock function is enabled and the User Password is forgotten then only the Master Password with a Security Erase Unit command can unlock the device. Then user data is erased. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 66: Figure 9 Initial Setting
< No Setting Password > Set Password with User Password Normal operation Normal operation Power off Power off Device locked mode Device unlocked mode Figure 9 Initial Setting HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 67: Figure 10 Usual Operation
Freeze Lock command Enter Device Frozen mode Normal Operation except Set Password, Disable Password, Erase Unit, Unlock commands. (*1) Refer to 9.6.5 on the page .65 Figure 10 Usual Operation HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 68: Figure 11 Password Lost
UNLOCK command are aborted until a hard reset or a power off. The count and EXPIRE bit are cleared after a power on reset or a hard reset. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 69: Table 39 Command Table For Device Lock Operation -1
SCT Read Status Executable Executable Executable Security Disable Password Command aborted Executable Command aborted Security Erase Prepare Executable Executable Command aborted Table 38 Command table for device lock operation -1 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 70: Table 40 Command Table For Device Lock Operation -2
Write Stream DMA Command aborted Executable Executable Write Stream PIO Command aborted Executable Executable Write Uncorrectable Ext Command aborted Executable Executable Table 39 Command table for device lock operation -2 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 71: Host Protected Area Feature
Make entire device be accessible including the protected area by setting device Maximum LBA as 12,692,735 (C1ACFFh) via Set Max Address command. The option could be either nonvolatile or volatile. Test the sectors for protected area (LBA >= 12,289,536 (BB8600h)) if required. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 72: Security Extensions
The IDENTIFY DEVICE response word 83, bit 8 indicates that this extension is supported if set, and word 86, bit 8 indicate the Set Max security extension enabled if set. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 73: Figure 12 Seek Overlap
So the host system can confirm the completion of write cache operation by issuing Soft reset, Standby (Immediate) command or Flush Cache command to the device before power off. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 74: Reassign Function
When a read operation for a sector failed once then recovered at the specific ERP step, this sector of data is reallocated automatically. A media verification sequence may be run prior to the relocation according to the pre-defined conditions. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 75: Power-Up In Standby Feature Set
Word 86, bit 3 indicates that Advanced Power Management is enabled if set. Word 91, bits 7-0 contain the current Advanced Power Management level if Advanced Power Management is enabled. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 76: Automatic Acoustic Management Feature Set (Aam)
Disable Address Offset Feature removes the address offset and sets the size of the drive reported by the Identify Device command back to the size specified in the last non-volatile Set Max Address command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 77: Figure 13 Device Address Map Before And After Set Feature
( Sy s t em r es er v ed ar ea) ( Us er Ar ea) LBA M - R LBA M LBA 0 Figure 13 Device address map before and after Set Feature LBA 0 LBA 0 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 78: Identify Device Data
HOB bit to zero in the Device Control register. The "most recently written" content always gets written by a register write regardless of the state of HOB in the Device Control register. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 79: Streaming Feature Set
AV content. One Stream ID may be configured for each read and write operation with different command completion time limits be each Configure Stream command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 80: Streaming Logs
These error logs are 512 bytes in length and retain the last 31 errors that occurred during any Streaming Data transfer. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 81: Sata Interface Power Management
SECURITY FREEZE LOCK: The Frozen mode setting established by the SECURITY FREEZE LOCK command. SECURITY UNLOCK: The unlock counter that is decremented as part of a failed SECURITY UNLOCK command attempt. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 82: Sata Ii Optional Features
CRC events to be incremented for the same event. Another example implementation difference is how a missing EOF event is recorded; a missing EOF primitive may imply a bad CRC even though HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 83 Not supported (R_ERR response for Host-to-Device Non-data FIS due to Optional 012h CRC errors) 013h Optional Not supported (R_ERR response for Host-to-Device Non-data FIS due to HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 84: Table 41 Phy Event Counter Identifiers
0h is found or the entire page has been read. A counter identifier with value 0h indicates that Table 41 the log page contains no more counter values past that point. Log page 11h is defined in Byte Reserved Reserved Reserved Reserved HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 85: Table 42 Read Log Ext Log Page 11H Data Structure Definition
Each byte shall be added with unsigned arithmetic and overflow shall be ignored. The sum of all 512 bytes of the data structure will be zero when the checksum is correct. Reserved All reserved fields shall be cleared to zero HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 86: Table 43 Sct Log Page And Direction
Action Code 2 (LBA Segment Access) supported Action Code 1 (Long Sector Access) supported SCT Feature Set supported (includes SCT status) Table 43 Identify Device Information Word 206 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 87: Table 45 Output Registers Of Sct Command Using Smart
7 6 5 4 3 2 1 0 Feature Sector Count Sector Number Cylinder Low Cylinder High Device/Head - D - Command Table 44 Output Registers of SCT Command Using SMART HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 88: Table 46 Input Registers Of Sct Command Using Smart
Previous Reserved LBA Mid Current Previous LBA High Current Reserved Previous Reserved Device/Head - D - Command Table 46 Input Registers of SCT Command Using Write Log Ext HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 89: Table 48 Output Registers Of Sct Command Using Write Log Ext
HOB=1 Reserved Device/Head Device/Head Status Status All ATA ―previous‖ registers are reserved in Write Log Ext responses. Table 47 Output Registers of SCT Command Using Write Log Ext HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 90: Table 49 Key Sector Format
0002h Write LBA Segment Access 0003h Error Recovery Control 0004h Features Control 0005h Read SCT Data Table 0006h-BFFFh Reserved C000h-FFFFh Vendor Specific Table 49 SCT Action Code List HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 91: Table 51 Extended Status Code
Read Long failure C005h Write Long failure C006h Write Cache enable failure C007h-FFEFh Vendor Specific FFF0h-FFFEh Reserved FFFFh SCT command executing in background Table 50 Extended Status Code HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 92: Table 52 Input Registers Of Sct Data Transfer Using Smart
LBA Mid Current Previous LBA High Current Reserved Previous Reserved Device/Head - D - Command 2Fh(Read)/3Fh(Write) Table 52 Input Registers of SCT Data Transfer using Read/Write Log Ext HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 93: Table 54 Intput Registers Of Sct Status Request Using Smart
Reserved LBA Mid Current Previous LBA High Current Reserved Previous Reserved Device/Head - D - Command Table 54 Input Registers of SCT Status Request Using Read Log Ext HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 94 Life Max Temp Maximum HDA temperature in degrees Celsius seen for the life of the drive. This is a 2‘s complement number. 80h indicates that this value is invalid. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 95: Table 56 Data Format Of Sct Status Response
Min Op Limit. See table 93 for information about this Interval. 479:214 Byte[275] Reserved 511:480 Byte[32] Vendor Specific Table 55 Data Format of SCT Status Response HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 96: Table 57 Lba Segment Access (Inputs)
Issuing this command with a value of zero for Start LBA and Count will cause all LBAs of the drive to be written the specified pattern. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 97 (except another complete write all), shall cause the Segment Initialized Flag to be cleared. Reallocations as a result of reading data (foreground or background) do not clear the Segment Initialized Flag. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 98 Cylinder High Device/Head Status Possible Extended Status Code for Blocking Operation (Function code = 0101h, 0102h) 0017h Blocking SCT Segment Access command was terminated because of unrecoverable error HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 99: Table 59 Error Recovery Control Command (Inputs)
These timers do not apply to streaming commands, or to queued commands when out-of-order data delivery is enabled. These command timers are volatile. The default value is 0 (i.e. disable command time-out). HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 100: Table 61 Feature Control Command (Inputs)
If Function Code was 0003h, then this is the MSB of Option Flags. Otherwise, this field is reserved. Cylinder Low reserved Cylinder High reserved Device/Head reserved Status Table 61 Feature Control command (Outputs) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 101: Table 63 Feature Code List
All remaining queue locations are set to 80h. The Sample Period, Max Op Limit, Over Limit, Min Op Limit and Under Limit values are preserved. Default value is 0001h. 0004h-CFFFh Reserved D000h-FFFFh Vendor Specific Table 62 Feature Code List HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 102: Table 64 Sct Data Table Command (Inputs)
Table 64 SCT Data Table command (Outputs) Table ID Description 0000h Invalid 0001h Reserved 0002h HDA Temperature History Table (in absolute degree C). See 0 0003h-CFFFh Reserved D000h-FFFFh Vendor Specific Table 65 Table ID HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 103 (at offset 34). The most recent temperature entered in the buffer is at Queue Index + 34. See Note 1 and Note 2. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 104: Table 67 Data Format Of Hda Absolute Temperature History Table
Logging Interval, the Queue Index shall be set to zero and the first queue location shall be set to the current Absolute HDA Temperature value. All remaining queue locations are set to 80h. Table 66 Data Format of HDA Absolute Temperature History Table HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 105: Command Protocol
Format Track  Security Disable Password  Security Erase Unit  Security Set Password  Security Unlock  Set Max Set Password command  Set Max Unlock command HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 106: Dma Data In Commands And Dma Data Out Commands
 Standby Immediate  Write Uncorrectable Ext Execution of these commands involves no data transfer. DMA Data In commands and DMA Data Out commands 10.4 These commands are: HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 107: First-Party Dma Commands
If a command is marked by the host as high priority, the device shall attempt to provide better quality of service for the command. It is not required that devices process all high priority requests before satisfying normal priority requests. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 108: Table 68 Command Set
Read Verify Sector(s) Read Verify Sector(s) Ext Recalibrate Security Disable Password Security Erase Prepare Security Erase Unit Security Freeze Lock Security Set Password Security Unlock Table 67 Command Set HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 109: Table 69 Command Set --Continued
PIO data OUT command Non data command DMA command Vendor specific command Table 68 Command Set --Continued-- Commands marked * are alternate command codes for previous defined commands. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 110: Table 70 Command Set (Subcommand)
Table 69 Command Set (Subcommand) on the page 106 shows the sub-commands they are supported by each command or feature. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 111 SATA interface specification. However, be careful that Serial ATA Device/Head register bit-4 (d) is different from that of Parallel ATA. In Serial ATA, Device/Head register bit-4 is reserved for all commands. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 112: Table 71 Check Power Mode Command (E5H/98H)
The power mode code. The command returns 0 in the Sector Count Register if the device is in Standby or Sleep mode. Otherwise, the Sector Count Register will be set to 0FFh. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 113: Table 72 Configure Stream Command (51H)
Command Abort is returned (see abort conditions for Error Register). In this case the old parameters for the specified Stream ID shall remain in effect. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 114 CCTL is 50ms.CCTL is set to 50ms when the specified value is shorter than 50ms. Sector Count Current Allocation Unit Size In Sectors (7:0) Sector Count Previous Allocation Unit Size In Sectors (15:8) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 115: Table 73 Device Configuration Overlay Command (B1H)
Set command and returns the content of the Identify Device or Identify Packet Device command response to the original settings as indicated by the data returned from the execution of a Device Configuration Identify command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 116 = word 7 is invalid Cylinder low = bit 8-15 are valid Sector Number = bit 3 is invalid Sector count = now Security feature set is enabled HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 117 1 = Supports native command queuing 9-20 Reserved 15-14 Reserved 1 = Support for WRITE UNCORRECTABLE is allowed 12-0 Reserved 22-254 Reserved Integrity word <Note .> 15-8 Checksum Signature (A5h) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 118: Table 75 Device Configuration Overlay Data Structure
Device is now SET MAX Locked or Frozen mode Protected area is now established DCO is not supported Subcommand code is invalid other reason Table 75 DCO error information definition HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 119: Table 77 Download Microcode Command (92H)
Sector Count register to create a 16-bit sector count value. The Sector Number register is the most significant eight bits and the Sector Count register is the least significant eight bits. A value of zero in both the Sector HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 120 If a software or hardware Reset is issued to the device before all of the microcode segments have been transferred to the device the device shall abandon all of the microcode segments received and process the Reset. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 121: Table 78 Execute Device Diagnostic Command (90H)
The normal Error Register bit definitions do not apply to this command. Instead, the register contains a Table 36 Diagnostic diagnostic code. See Codes‖ on the page 55 for its definition. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 122: Table 79 Flush Cache Command (E7H)
This command causes the device to complete writing data from its cache. The device returns good status after data in the write cache is written to disk media. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 123: Table 80 Flush Cache Ext Command (Eah)
This command causes the device to complete writing data from its cache. The device returns good status after data in the write cache is written to disk media. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 124: Table 81 Format Track Command(50H)
Since device performance is optimal at 1:1 interleave, and the device uses relative block addressing internally, the device will always format a track in the same way no matter what sector numbering is specified in the format table. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 125 The Error Register. An Abort error (ABT=1) will be returned when LBA out of range. In LBA mode, this command formats a single logical track including the specified LBA. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 126: Table 82 Format Unit Command (F7H)
This command does not request to data transfer. Command execution time depends on drive capacity. To determine command timeout value, Word 89 of Identify Device data should be referred. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 127: Table 83 Identify Device Command (Ech)
The Identify Device command requests the device to transfer configuration information to the host. The device will transfer a sector to the host containing the information described in the following pages. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 128: Table 84 Identify Device Information
14(=1) : Shall be set to one 13-1(=0) : Reserved for the Trusted Computing Group 0(=0) : 0=Trusted Computing feature set is not supported Table 83 Identify device information HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 129: Table 85 Identify Device Information --Continued
'11' = PIO Mode 3 and 4 Supported Minimum Multiword DMA Transfer Cycle Time Per Word 0078H 15-0(=78) Cycle time in nanoseconds (120ns, 16.6MB/s) Table 84 Identify device information --Continued-- HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 130: Table 86 Identify Device Information --Continued
ATA-2, ATA-3, ATA/ATAPI-4, ATA/ATAPI-5, ATA/ATAPI-6. ATA/ATAPI-7 15-0(=1FCh) and ATA8-ACS 0029H Minor version number 15-0(=29h) ATA8-ACS Revision 4 Table 85 Identify device information --Continued— * 3.0Gbps is supported, however the default setting is 1.5Gbps. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 131: Table 87 Identify Device Information --Continued
PACKET Command feature set 3 (=1) Power management feature set 2 (=0) Removable feature set 1 (=1) Security feature set 0 (=1) SMART feature Set Table 86 Identify device information --Continued— HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 132: Table 88 Identify Device Information --Continued
LOOK AHEAD WRITE CACHE PACKET Command feature set Power management feature set Removable media feature set Security feature set SMART feature set Table 87 Identify device information --Continued— HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 133: Table 89 Identify Device Information --Continued
Media Card Pass Through Command feature set enabled 2 (=0) Media serial number is valid 1 (=1) SMART self-test supported 0 (=1) SMART error logging supported Table 88 Identify device information --Continued— HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 134: Table 90 Identify Device Information --Continued
0000H Time required for Enhanced security erase completion 0000H Current Advanced power management value FFFEH Current Password Revision Code 0000H COMRESET result Table 89 Identify device information --Continued— HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 135: Table 91 Identify Device Information --Continued
1=Write Uncorrectable is supported. 0=Write-Read-Verify feature set is not enabled Reserved 121-126 0000H Reserved 0000H Removable Media Status Notification feature set 0000H=Not supported Table 90 Identify device information --Continued— HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 136: Table 92 Identify Device Information --Continued
SCT Feature Set 1= Support (includes SCT status) Table 91 Identify device information --Continued— Note. The '*' mark in 'Content' field indicates the use of those parameters are vendor specific. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 137: Table 93 Identify Device Information --Continued
Checksum. This value is the two's complement of the sum of all bytes in byte 0 xxA5H 15-8 through 510 7-0 (A5) Signature Table 92 Identify device information --Continued— HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 138: Table 94 Idle Command (E3H/97H)
When the Idle mode is entered, the device is spun up to operating speed. If the device is already spinning, the spin up sequence is not executed. During Idle mode the device is spinning and ready to respond to host commands immediately. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 139 The timeout interval will be reinitialized if there is a drive access before the timeout interval expires. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 140: Table 95 Idle Immediate Command (E1H/95H)
During Idle mode the device is spinning and ready to respond to host commands immediately. The Idle Immediate command will not affect to auto power down timeout parameter. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 141: Table 96 Initialize Device Parameters Command (91H)
Note: The following conditions needs to be satisfied to avoid invalid number of cylinders beyond FFFFh. (Total number of user addressable sectors)/((Sector Count)*(H+1)) = < FFFFh The total number of user addressable sectors is described in Identify Device command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 142: Table 97 Read Buffer Command (E4H)
The sector transferred will be from the same part of the buffer written to by the last Write Buffer command. The contents of the sector may be different if any reads or writes have occurred since the Write Buffer command was issued. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 143: Table 98 Read Dma Command (C8H/C9H)
DMARQ and are performed by the slave-DMA channel. The device issues only one interrupt per command to indicate that data transfer has terminated and status is available. If an uncorrectable error occurs, the read will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 144 In LBA mode, this register contains current LBA bits 8-15 (Low), 16-23 (High). (L=1) The head number of the sector to be transferred. (L=0) In LBA mode, this register contains current LBA bits 24-27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 145: Table 99 Read Dma Ext Command (25H)
DMARQ and are performed by the slave-DMA channel. The device issues only one interrupt per command to indicate that data transfer has terminated and status is available. If an uncorrectable error occurs, the read will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 146 LBA (39:32)of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16)of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40)of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 147: Table 100 Read Fpdma Queued Command (60H)
The Read FPDMA command reads one or more sectors of data from disk media, and then transfers the data from the device to the host. If an uncorrectable error occurs, the read will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 148 LBA (39:32)of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16)of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40)of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 149: Table 101 Read Log Ext Command (2Fh)
Status Register DRQ COR Table 100 Read Log Ext Command (2Fh) This command returns the specified log to the host. The device shall interrupt for each DRQ block transferred. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 150: Table 102 Log Address Definition
If the feature set associated with the log specified in the Sector Number register is not supported or enabled, or if the values in the Sector Count, Sector Number or Cylinder Low registers are invalid, the device shall return command aborted. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 151: Table 103 General Purpose Log Directory
The value of the General Purpose Logging Version word shall be 0001h. A value of 0000h indicates that there is no General Purpose Log Directory. The logs at log addresses 80-9Fh shall each be defined as 16 sectors long. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 152: Extended Comprehensive Smart Error Log
Unused error log data structures shall be filled with zeros. Data format of each error log structure is shown below. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 153: Table 105 Extended Error Log Data Structure
Note: bits (7:0) refer to the most recently written contents of the register. Bits (15:8) refer to the contents of the register prior to the most recent write to the register. Table 105 Command data structure HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 154: Table 107 Error Data Structure
Value State Unknown Sleep Standby Active/Idle SMART Off-line or Self-test x5h-xAh Reserved xBh-xFh Vendor specific Note: The value of x is vendor specific. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 155: Table 108 Extended Self-Test Log Data Structure
This indicates the most recent self-test descriptor. If there have been no self-tests, this is set to zero. Valid values for the Self-test descriptor index are 0 to 18. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 156: Table 109 Extended Self-Test Log Descriptor Entry
Self-test failure check point Failing LBA (7:0) Failing LBA (15:8) Failing LBA (23:16) Failing LBA (31:24) Failing LBA (39:32) Failing LBA (47:40) Vendor specific Table 108 Extended Self-test log descriptor entry HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 157: Table 110 Command Error Information
The Data Structure Checksum (Byte 511) contains the 2‘s complement of the sum of the first 511 bytes in the data structure. The sum of all 512 bytes of the data structure will be zero when the checksum is correct. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 158: Table 111 Read Stream Error Log
Read Stream Error Log Count Reserved Read Stream Error Log Entry #1 Read Stream Error Log Entry #2 Read Stream Error Log Entry #31 1F0h Table 110 Read Stream Error Log HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 159: Table 112 Stream Error Log Entry
Byte (13:12) indicate the length of the error. Therefore, each entry may describe a range of sectors at the given address and spanning the specified number of sectors. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 160: Table 113 Write Stream Error Log
The Error Log Index indicates the error log data structure representing the most recent error. Only values (31:0) are valid. Table 110 defines the format of each entry in the Error Log. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 161: Table 114 Streaming Performance Parameters Log
Time that may be required to begin access at new stream access position, in (n+2)-(n+3) (Identify Device words (99:98))/256 time units Table 116 Access Time Array Entry (Linearly Interpolated) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 162: Table 118 Read Multiple Command (C4H)
The sectors are transferred through the Data Register 16 bits at a time. Command execution is identical to the Read Sector(s) command except that an interrupt is generated for each block (as defined by the Set Multiple command) instead of for each sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 163: Table 119 Read Multiple Ext Command (29H)
The sectors are transferred through the Data Register 16 bits at a time. Command execution is identical to the Read Sector(s) command except that an interrupt is generated for each block (as defined by the Set Multiple command) instead of for each sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 164 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 165: Table 120 Read Native Max Address (F8H)
In CHS mode, this register contains native max cylinder number. (L=0) In LBA mode, this register contains native max LBA bits 24-27. (L=1) In CHS mode, this register contains native max head number.(L=0) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 166: Table 121 Read Native Max Address Ext (27H)
DRQ COR Table 120 Read Native Max Address Ext (27h) This command returns the native max LBA of HDD which is not effected by Set Max Address Ext command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 167 LBA (39:32) of the address of the Native max address. Cylinder High (HOB=0) LBA (23:16) of the address of the Native max address. Cylinder High (HOB=1) LBA (47:40) of the address of the Native max address. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 168: Table 122 Read Sector(S) Command (20H/21H)
The sectors are transferred through the Data Register 16 bits at a time. If an uncorrectable error occurs, the read will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 169 In LBA mode, this register contains current LBA bits 8 – 15 (Low), 16 – 23 (High). (L=1) The head number of the last transferred sector. (L=0) In LBA mode, this register contains current LBA bits 24 – 27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 170: Table 123 Read Sector(S) Ext Command (24H)
The sectors are transferred through the Data Register 16 bits at a time. If an uncorrectable error occurs, the read will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 171 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 172: Table 124 Read Stream Dma Command (2Ah)
Command Completion Time Limit expired by setting the CCTO bit in the error log to one, In all cases, the device shall attempt to transfer the amount of data requested within the Command HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 173 LBA (7:0) of the address of the first unrecoverable error. Sector Number (HOB=1) LBA (31:24) of the address of the first unrecoverable error. Cylinder Low (HOB=0) LBA (15:8) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 174 ERR bit shall be cleared to zero, and the bits that would normally be set in the Error register shall be set in the error log. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 175: Table 125 Read Stream Pio Command (2Bh)
In all cases, the device shall attempt to transfer the amount of data requested within the Command Completion Time Limit event if some data transferred is in error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 176 LBA (15:8) of the address of the first unrecoverable error. Cylinder Low (HOB=1) LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 177 UNC, IDNF, ABRT, or CCTO error occurs, the SE bit shall be set to one, the ERR bit shall be cleared to zero, and the bits that would normally be set in the Error register shall be set in the error log. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 178: Table 126 Read Verify Sector(S) Command (40H/41H)
The difference between Read Sector(s) command and Read Verify Sector(s) command is whether the data is transferred to the host or not. If an uncorrectable error occurs, the read verify will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 179 In LBA mode, this register contains current LBA bits 8 – 15 (Low), 16 – 23 (High). (L=1) The head number of the last transferred sector. (L=0) In LBA mode, this register contains current LBA bits 24 – 27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 180: Table 127 Read Verify Sector(S) Ext Command (42H)
The difference between the Read Sector(s) Ext command and the Read Verify Sector(s) Ext command is whether the data is transferred to the host or not. If an uncorrectable error occurs, the Read Verify Sector(s) Ext will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 181 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 182: Table 128 Recalibrate Command (1Xh)
The Recalibrate command moves the read/write heads from anywhere on the disk to cylinder 0. If the device cannot reach cylinder 0, T0N (Track 0 Not Found) will be set in the Error Register. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 183: Table 129 Security Disable Password Command (F6H)
User Password. This command should be executed in device unlock mode. When security is disabled and the Identifier bit is set to User, then the device shall return command aborted. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 184: Table 130 Password Information For Security Disable Password Command
Zero indicates that the device should check the supplied password against the user password stored internally. One indicates that the device should check the given password against the master password stored internally. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 185: Table 131 Security Erase Prepare Command (F3H)
The Security Erase Prepare Command must be issued immediately before the Format Unit Command. This command is to prevent accidental erasure of the device. This command does not request to transfer data. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 186: Table 132 Security Erase Unit Command (F4H)
This command requests to transfer a single sector data from the host including information specified in on the page 182. When security is disabled and the Identifier bit is set to User, then the device shall return command aborted. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 187: Table 133 Erase Unit Information
NOT compared with the password stored in the device for both the Master Password and the User Password, and then the device only erases all user data. The execution time of this command is set in word 89 of Identify device information. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 188: Table 134 Security Freeze Lock Command (F5H)
The following commands are rejected when the device is in frozen mode. For detail, refer to on the page 6566.  Security Set Password  Security Unlock  Security Disable Password  Security Erase Unit HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 189: Table 135 Security Set Password Command (F1H)
This command requests a transfer of a single sector of data from the host including the information specified in Table 134 on the page 185. The data transferred controls the function of this command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 190: Table 136 Security Set Password Information
The master password previously set is still stored in the file but may NOT be used to unlock the device. Identifier=Master / Security level = Maximum This combination will set a master password but will NOT enable the security mode feature (lock function). HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 191: Table 137 Security Unlock Command (F2H)
This counter is initially set to 5 and is decremented for each password mismatch. When security is disabled and the Identifier bit is set to User, then the device shall return command aborted. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 192: Table 138 Security Unlock Information
AFTER the password information has been sent to the device. If an abort error is returned by the device BEFORE the password data has been sent to the file then another problem exists. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 193: Table 139 Seek Command (7Xh)
In LBA mode, this register contains current LBA bits 8 – 15 (Low), 16 – 23 (High). Cylinder High/Low (L=1) In LBA mode, this register contains current LBA bits 24 – 27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 194: Table 140 Set Features Command (Efh)
The Set Feature command is to establish the following parameters which affect the execution of certain features as shown in below table. ABT will be set to 1 in the Error Register if the Feature register contains any undefined values. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 195 After power on reset or hard reset, the device is set to the following features as default. Write cache : Enable Read look-ahead : Enable Reverting to power on defaults : Disable Release interrupt : Disable HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 196: Set Transfer Mode
When Low RPM standby mode is the deepest Power Saving mode and the value in Sector Count register is between 40h and 7Fh, 120<=Y <=435 [sec] (default: 120 [sec]) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 197 If Low power idle mode is disabled (i.e., y has not been set yet), y becomes 120[sec] when Low RPM standby mode is enabled. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 198: Automatic Acoustic Management
The Typical PIO Mode Host Interface Sector Time includes the host‘s interrupt service time. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 199: Table 141 Set Max Address (F9H)
Identify device command returns the Address which is set via this command as a default value. If the device in Address Offset mode receives this command with the nonvolatile option, the device returns aborted error to the host. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 200 In CHS mode, this register contains max cylinder number which is set. (L=0) In LBA mode, this register contains max LBA bits 24 – 27 which is set. (L=1) In CHS mode, this register contains max head number.(L=0) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 201: Table 142 Set Max Set Password
The password is retained by the device until the next power cycle. When the device accepts this command the device is in Set_Max_Unlocked state. Word Description Reserved 01-16 Password (32 byte) 17-255 Reserved Table 142 Set Max Set Password data contents HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 202: Table 144 Set Max Lock
Set Max Unlock and Set Max Freeze Lock are rejected. The device remains in this state until a power cycle or the acceptance of a Set Max Unlock or Set Max Freeze Lock command. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 203: Table 145 Set Max Unlock (F9H)
Set Max Unlock commands are rejected until a hard reset or a power off. If the password compares matches, then the device set the Set_Max_Unlocked state and all Set Max commands shall be accepted. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 204: Table 146 Set Max Freeze Lock (F9H)
The Set Max Freeze Lock command sets the device to Set_Max_Frozen state. After command completion any subsequent Set Max commands are rejected. Commands disabled by Set Max Freeze Lock are: Set Max Address Set Max Set PASSWORD Set Max Lock Set Max Unlock HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 205: Table 147 Set Max Address Ext Command (37H)
(61:60) shall not be modified. When the address requested is equal to or less than 268,435,455, words (103:100) shall be modified to reflect the requested value, and words (61:60) shall also be modified. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 206 Cylinder Low (HOB=0) Set Max LBA (15:8). Cylinder Low (HOB=1) Set Max LBA (39:32). Cylinder High (HOB=0) Set Max LBA (23:16). Cylinder High (HOB=1) Set Max LBA (47:40). HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 207: Table 148 Set Multiple Command (C6H)
The block size to be used for Read Multiple and Write Multiple commands. Valid block sizes can be selected from 0, 1, 2, 4, 8 or 16. If 0 is specified, then Read Multiple and Write Multiple commands are disabled. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 208: Table 149 Sleep Command (E6H/99H)
The device is spun down and the interface becomes inactive. If the device is already spun down, the spin down sequence is not executed. The only way to recover from Sleep Mode is with a software reset or a hardware reset. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 209: Table 150 Smart Function Set Command (B0H)
The SMART Function Set command has several separate subcommands which are selectable via the device‘s Features Register when the SMART Function Set command is issued by the host. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 210: Smart Subcommand
The SMART Disable Operations subcommand disables the autosave feature along with the device‘s SMART operations. Upon the receipt of the subcommand from the host, the device asserts BSY, enables or disables the Autosave feature, clears BSY and asserts INTRQ. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 211 Set ERR to one when self-test has failed Error Set ABRT to one when self-test has failed Cyl Low Set to F4h when self-test has failed Cyl High Set to 2Ch when self-test has failed HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 212: Table 104 Extended Comprehensive Smart Error Log
– with the exception of SMART Enable Operations – are disabled, and invalid and will be aborted by the device (including the SMART Disable Operations subcommand), returning the error code as specified in 0 on the page 222. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 213 Automatic Off-Line Data Collection, but the device may respond with the error code specified in 0 on the page.222 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 214: Table 152 Device Attribute Data Structure
The Data Structure Revision Number identifies which version of this data structure is implemented by the device. This revision number identifies both the Attribute Value and Attribute Threshold Data structures. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 215: Table 153 Individual Attribute Data Structure
Device Power Cycle Count Power off Retract count Load Cycle count Temperature Reallocation Event Count Current Pending Sector Count Off-Line Scan Uncorrectable Sector Count Ultra DMA CRC Error Count HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 216 Off-line data collection never started All segments completed without errors. Off-line data collection suspended by interrupting command Off-line data collecting aborted by interrupting command Off-line data collection aborted with fatal error HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 217 Self-test implemented bit Self-test routine is not implemented Self-test routine is implemented Reserved (0) Selective self-test implemented bit Selective self-test routine is not implemented Selective self-test routine is implemented HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 218 Data Structure Checksum The Data Structure Checksum is the 2‘s compliment of the result of a simple 8-bit addition of the first 511 bytes in the data structure. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 219: Table 154 Device Attribute Thresholds Data Structure
Data Structure Checksum The Data Structure Checksum is the 2‘s compliment of the result of a simple 8-bit addition of the first 511 bytes in the data structure. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 220: Table 156 Smart Log Directory
SMART Log Directory The value of the SMART Logging Version word shall be 01h. The logs at log addresses 80-9Fh shall each be defined as 16 sectors long. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 221: Table 157 Smart Summary Error Log Sector
This points the most recent error log data structure. Only values 1 through 5 are valid. 11.42.5.3 Device error count This field contains the total number of errors. The value will not roll over. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 222: Table 158 Error Log Data Structure
Features register Sector count register Sector number register Cylinder Low register Cylinder High register Device/Head register Command register Timestamp (milliseconds from Power On) Table 158 Command data structure HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 223: Table 160 Error Data Structure
State field contains a value indicating the device state when command was issued to the device. Value State Unknown Sleep Standby Active/Idle SMART Off-line or Self-test x5h-xAh Reserved xBh-xFh Vendor specific Note: The value of x is vendor specific. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 224: Table 161 Self-Test Log Data Structure
After 21 descriptors have been recorded, the oldest descriptor will be overwritten with new descriptor. Self-test index points the most recent descriptor. When there is no descriptor the value is 0. When there is descriptor(s) the value is 1 through 21. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 225: Table 162 Selective Self-Test Log Data Structure
When set to one, off-line scan after selective test is pending. When set to one, off-line scan after selective test is active. 5-15 Reserved. Table 162 Selective self-test feature flags HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 226: Table 164 Smart Error Codes
The device is unable to read its Attribute Values or Attribute Thresholds data 10h or 40h structure. The device is unable to write to its Attribute Values data structure. 10h or 01h Table 163 SMART Error Codes HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 227: Table 165 Standby Command (E2H/96H)
During the Standby mode the device will respond to commands, but there is a delay while waiting for the spindle to reach operating speed. The automatic power down sequence is enabled and the timer starts counting down when the drive returns to Idle mode. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 228 The timeout interval will be reinitialized if there is a drive access before the timeout interval expires. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 229: Table 166 Standby Immediate Command (E0H/94H)
During the Standby mode, the device will respond to commands, but there is a delay while waiting for the spindle to reach operating speed. The Standby Immediate command will not affect the auto power down timeout parameter. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 230: Table 167 Write Buffer Command (E8H)
Data Register 16 bits at a time. The Read Buffer and Write Buffer commands are synchronized such that sequential Write Buffer and Read Buffer commands access the same 512 byte within the buffer. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 231: Table 168 Write Dma Command (Cah/Cbh)
The device issues only one interrupt per command to indicate that data transfer has terminated and status is available. If an uncorrectable error occurs, the write will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 232 In LBA mode, this register contains current LBA bits 8 – 15 (Low), 16 – 23 (High). (L=1) The head number of the last transferred sector. (L=0) In LBA mode, this register contains current LBA bits 24 – 27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 233: Table 169 Write Dma Fua Ext Command (3Dh)
The device issues only one interrupt per command to indicate that data transfer has terminated and status is available. If an unrecoverable error occurs, the write will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 234 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 235: Table 170 Write Dma Ext Command (35H)
The device issues only one interrupt per command to indicate that data transfer has terminated and status is available. If an uncorrectable error occurs, the write will be terminated at the failing sector HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 236 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 237: Table 171 Write Fpdma Queued Command (61H)
The Write FPDMA Queued command transfers one or more sectors of data from the host to the device, and then the data is written to the disk media. If an unrecoverable error occurs, the write will be terminated at the failing sector HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 238 LBA (39:32)of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16)of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40)of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 239: Table 172 Write Log Ext Command (3Fh)
Write Log Ext Command (3Fh) This command writes a specified number of 512 byte data sectors to the specific log. The device shall interrupt for each DRQ block transferred. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 240 Sector Count, Sector Number or Cylinder Low registers are invalid, the device shall return command aborted. If the host attempts to write to a read only log address, the device shall return command aborted. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 241: Table 173 Write Multiple Command (C5H)
Command execution is identical to the Write Sector(s) command except that an interrupt is generated for each block (as defined by the Set Multiple command) instead of for each sector. The sectors are transferred through the Data Register 16 bits at a time. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 242 In LBA mode, this register contains current LBA bits 8 - 15 (Low), 16 - 23 (High). (L=1) The head number of the last transferred sector. (L=0) In LBA mode, this register contains current LBA bits 24 - 27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 243: Table 174 Write Multiple Ext Command (39H)
Command execution is identical to the Write Sector(s) Ext command except that an interrupt is generated for each block (as defined by the Set Multiple command) instead of for each sector. The sectors are transferred through the Data Register 16 bits at a time. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 244 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 245: Table 175 Write Multiple Fua Ext Command (Ceh)
Command execution is identical to the Write Sector(s) Ext command except that an interrupt is generated for each block (as defined by the Set Multiple command) instead of for each sector. The sectors are transferred through the Data Register 16 bits at a time. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 246 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 247: Table 176 Write Sector(S) Command (30H/31H)
The sectors are transferred through the Data Register 16 bits at a time. If an uncorrectable error occurs, the write will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 248 In LBA mode, this register contains current LBA bits 8 - 15 (Low), 16 - 23 (High). (L=1) The head number of the last transferred sector. (L=0) In LBA mode, this register contains current LBA bits 24 - 27. (L=1) HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 249: Table 177 Write Sector(S) Ext Command (34H)
The sectors are transferred through the Data Register 16 bits at a time. If an uncorrectable error occurs, the write will be terminated at the failing sector. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 250 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 251: Table 178 Write Stream Dma Command (3Ah)
In all cases, the device shall attempt to transfer the amount of data requested within the Command Completion Time Limit event if some data transferred is in error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 252 Cylinder High Current LBA (23:16). Cylinder High Previous LBA (47:40). Input Parameters From The Device Sector Number (HOB=0) LBA (7:0) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 253 LBA (47:40) of the address of the first unrecoverable error. CCTO (Error, bit 0) CCTO bit shall be set to one if a Command Completion Time Limit Out error has occurred. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 254: Table 179 Write Stream Pio Command (3Bh)
In all cases, the device shall attempt to transfer the amount of data requested within the Command Completion Time Limit event if some data transferred is in error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 255 Sector Number Current LBA (7:0). Sector Number Previous LBA (31:24). Cylinder Low Current LBA (15:8). Cylinder Low Previous LBA (39:32). Cylinder High Current LBA (23:16). Cylinder High Previous LBA (47:40). HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 256 LBA (47:40) of the address of the first unrecoverable error. CCTO (Error, bit 0) CCTO bit shall be set to one if a Command Completion Time Limit Out error has occurred. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 257: Table 180 Write Uncorrectable Ext Command (45H)
‗uncorrectable‘ sector location has actual physical errors. In this case read commands and/or write commands shall return ERR status information that is consistent with the error. The pseudo uncorrectable or HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 258 LBA (39:32) of the address of the first unrecoverable error. Cylinder High (HOB=0) LBA (23:16) of the address of the first unrecoverable error. Cylinder High (HOB=1) LBA (47:40) of the address of the first unrecoverable error. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 259 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 260: Table 181 Timeout Values
The device sets BSY(=0) and 30 sec transfer Status Register DRQ(=1) to the Status Register and sends a PIO SETUP FIS to the host. Table 180 Timeout Values HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 261: Table 182 Timeout Values --Continued
The abbreviations "ns", "us", "ms" and "sec" mean nanoseconds, microseconds, milliseconds and seconds, respectively. We recommend that the host system executes Soft reset and then retries to issue the command if the host system timeout would occur for the device. HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 262 Read Stream DMA (2Ah) .......... 168 Read Stream PIO (2Bh) ..........171 Read Verify Sector(s) (40h/41h) ........ 174 Read Verify Sector(s) Ext (42h) ........ 176 Recalibrate (1xh) ............178 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 263 Power Management Commands ........57 UNC ................. 50 Power Management Feature .......... 57 Urgent bit ............76, 82, 83 Power Mode ..............57 User Password ..............62 Power On Reset ............... 54 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...
Page 264 Write Cache Function ............. 69 Write Continuous bit ............76 WTG ................. 48 HITACHI Deskstar & CinemaStar 7K1000.B & Deskstar E7K1000 Hard Disk Drive specification...

Hitachi HDS721050CLA362 Specifications

2 General Features

3 0 Fixed Disk Subsystem Description

4 Drive Characteristics

5 Defect Flagging Strategy

6 0 Specification

9 General Operation Descriptions

11 Command Descriptions

Quick Links

Hard disk drive specifications

Related Manuals for Hitachi HDS721050CLA362

Summary of Contents for Hitachi HDS721050CLA362