Advertisement
Quick Links
'Config A'
shown
This shed kit can be built two ways!
Choose roof
slope direction
to suit your site.
Config A
Please make a decision now and read
ahead to get a good understanding of
the steps required before beginning
contruction.
• Pages 1 to 14 are common
• Pages 15 to 19 are Config A specific
• Pages 20 to 25 are Config B specific
AU: 1800 029 701
+1 (866) 788 3046
+1 (866) 788 3046
N Z: 0800 466 444
Absco Industries
Assembly Instruction Manual
ABSCO NARROW SHED
MODEL: 15231NK-PTX
5' W x 7' D x 6' 10" H
Config B
admin@absco.com.au
admin@absco.com.au
www.abscogardensheds.com
www.abscosheds.com.au
When laying a concrete slab for your shed, it is
best practise to have a rebated edge to prevent
water ingress.
Rebated section is 1" high and inset 3" on all sides
from the overall slab base dimensions
WALLS SIT
ON THIS LEVEL
RAISED FLOOR
INSIDE SHED
4"
3"
1"
PLEASE LEAVE A REVIEW
www.abscosheds.com.au/review
Model: 15231NK-PTX
Australian Made
Overall slab base
dimensions for this
model are as shown
above.
3"
Illustration not to
23/11/23
1.0
scale.
1
Advertisement
Related Manuals for ABSCO SHEDS 15231NK-PTX
Summary of Contents for ABSCO SHEDS 15231NK-PTX
- Page 1 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H Australian Made ‘Config A’ shown This shed kit can be built two ways! When laying a concrete slab for your shed, it is best practise to have a rebated edge to prevent Choose roof water ingress.
- Page 2 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H Australian Made GENERAL INSTRUCTIONS SAFETY NOTES • Before commencing any assembly, read • Some parts may have sharp edges. It is through these instructions in detail to gain...
- Page 3 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H COMPONENTS LIST Nominal sheet widths are shown +/- 1/8” is within tolerance DESCRIPTION PART # DESCRIPTION PART # STEEL SHEET STEEL SHEET 80” x 30.4” 70.3” x 30.4”...
- Page 4 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H COMPONENTS LIST DESCRIPTION PART # DESCRIPTION PART # CHANNEL CHANNEL 81DL 81DR 44.3” 44.3” CHANNEL CHANNEL 81CL 81CR 44.3” 44.3” CHANNEL CHANNEL 59.5” 59.5” CHANNEL CHANNEL 59.5”...
- Page 5 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H Australian Made SNAPTiTE ASSEMBLY GUIDE The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for tools and fasteners. To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
- Page 6 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H Australian Made Guide on Joining Spliced Channels The text marked on all parts must be shown on the same side as each other JOIN>> JOIN>> <<JOIN JOIN>>...
- Page 7 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H Australian Made PRE-ASSEMBLY OF SPLICED CHANNELS Join together 12 x channel sections using 6 x channel joiners (Part CSJ) NOTE: Some channels may have holes in them - You will need to redrill holes where CSJ joining channel covers them.
- Page 8 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H REAR PANEL ASSEMBLY 1x required. 1. Overlap two 30A sheets by one rib as shown. Turn one sheet so edge holes are to the outside as pictured.
- Page 9 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H ROOF PANEL ASSEMBLY 1x required. 1. Layout and overlap sheets by one rib as shown. 2. Use 4x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes.
- Page 10 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H 2.0m H SIDE PANEL 1x required. 1. Layout and overlap sheets by one rib as shown. Orientate outside sheets as pictured. 2. Use 3x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes.
- Page 11 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H 5’11” H SIDE PANEL 1x required. 1. Layout and overlap sheets by one rib as shown. Orientate outer sheets with holes to the outside as pictured.
- Page 12 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H DOOR PANEL ASSEMBLY 1. Position the DoorB sheet as shown and attach the top 1x required. and bottom channels using the SNAP-TiTE method. Make sure you have the shorter, 0.6”...
- Page 13 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H DOOR PANEL ASSEMBLY 8. Turn the door over as shown. CONTINUED 91As overlap here 9. Now we’ll fit the two 91A jamb door braces. Align the holes in the brace with holes in the door.
- Page 14 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H FRONT PANEL 1x required. 1. Orientate the 34A sheet as shown and place the 89A jamb on top. 2. Use 2x 3/8” self tapping screws FAST001 per overlap, through the pre punched holes in the parts.
- Page 15 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H ATTENTION! Config is listed The following pages show how to build the on each page ‘Config A’ version of the shed as pictured. here If you would like to build ‘Config B’ go to page 20.
- Page 16 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H ATTACH GABLE PANELS FRONT PANEL ASSEMBLY 7. Turn the front panel over. CONTINUED 8. Take the 16L gable panel and align the hole pattern with the interior side of the 77J channel.
- Page 17 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H ATTACH DOOR TO FRONT PANEL 1. Use the supplied 1/8” drill bit DRILL and go through these existing jamb holes and into the sheet behind. 2. Lay the door in the open position so the hinges dangle over their matching holes.
- Page 18 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H PANEL CONSTRUCTION 1. Start with the front panel, open the door to help stand it 2. Attach the 5’11” H side panel next. Sit the side wall channel inside the end wall channels as shown below.
- Page 19 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H 5. Square up the shed walls. FINAL CONSTRUCTION Make sure they’re straight and check opposite corner-to-corner dimensions are equal. 6. Safely place roof panel on top...
- Page 20 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H The following pages show how to build the Config is listed ‘Config B’ version of the shed as pictured. on each page here If you would like to build ‘Config A’ go back to page 15.
- Page 21 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H ATTACH GABLE PANELS FRONT PANEL ASSEMBLY 7. Turn the front panel over. CONTINUED 8. Take the 16R gable panel and align the hole pattern with the interior side of the 77E channel.
- Page 22 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H ATTACH DOOR TO FRONT PANEL 1. Use the supplied 1/8” drill bit DRILL and go through these existing jamb holes and into the sheet behind. 2. Lay the door in the open position so the hinges dangle over their matching holes.
- Page 23 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H PANEL CONSTRUCTION 1. Start with the front panel, open the door to help stand it 2. Attach the 5’11” H side panel next. Sit the side wall channel inside the end wall channels as shown below.
- Page 24 ABSCO NARROW SHED MODEL: 15231NK-PTX 5’ W x 7’ D x 6’ 10” H 5. Square up the shed walls. FINAL CONSTRUCTION Make sure they’re straight and check opposite corner-to-corner dimensions are equal. 6. Safely place roof panel on top...
- Page 25 Absco Sheds Storage Guidelines • Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fi xings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.
- Page 26 THE CUSTOMER SERVICE MANAGER, ABSCO SHEDS, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110 PHONE: +61 1800 029701 EMAIL: warranty@absco.com.au...