Advertisement
Table of Contents
- 1 Table of Contents
- 2 Introduction
- 3 Warning
- 4 Important Installation Information
- 5 Step 1: Ventilation Requirements
- 6 Step 2: Cabinet Preparation
- 7 Step 3: Unpacking, Moving and Placing the Range
- 8 Step 4: Install Anti-Tip Device
- 9 Step 5: Gas Requirements & Hookup
- 10 Step 6: Electrical Requirements, Connection & Grounding
- 11 Step 7: Backguard Installation
- 12 Step 8: Test and Adjustment
- 13 To Clean and Protect Exterior Surfaces
- 14 Installer Checklist
- Download this manual
See also:
Care and Use Manual
INSTALLATION INSTRUCTIONS MANUAL
ALL-GAS MODELS – PRG304, PRG36 AND PRG48
DUAL-FUEL MODELS - PRDS304, PRDS36 AND PRDS48
IMPORTANT: LOCAL CODES VARY. INSTALLATION, ELECTRICAL CONNECTIONS,
GAS CONNECTIONS, AND GROUNDING MUST COMPLY WITH ALL APPLICABLE CODES.
IMPORTANT: Save these instructions for the Local Electrical Inspector's use.
INSTALLER: Please leave these Installation Instructions with this unit for the owner.
OWNER: Please retain these instructions for future reference.
Gas Supply:
Natural Gas – 6 inch water column. (14.9mb) min., 8 inch (20mb) nominal
Propane Gas – 11 inch water column. (27.4 mb), 14 inch (37mb) maximum
Electrical Power Supply:
PRG304, PRG36 and PRG48 Models – 120 VAC, 60 Hz., 1Ph., 20 Amp circuit.
PRDS304 Model - 120/240 VAC, 50/60 HZ., 1Ph., 20 Amp circuit.
PRDS36 Models – 120/240 VAC, 50/60 Hz., 1Ph., 35 Amp circuit.
PRDS48 Models – 120/240 VAC, 50/60 Hz., 1Ph., 50 Amp circuit.
PROFESSIONAL RANGES
PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
A P P R O V E D
®
WARNING: Disconnect power
before installing. Before turning
power ON, be sure that all
controls are in the OFF position.
Advertisement
Table of Contents
Related Manuals for Thermador PRG304
Summary of Contents for Thermador PRG304
- Page 1 INSTALLATION INSTRUCTIONS MANUAL PROFESSIONAL RANGES ALL-GAS MODELS – PRG304, PRG36 AND PRG48 DUAL-FUEL MODELS - PRDS304, PRDS36 AND PRDS48 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: LOCAL CODES VARY. INSTALLATION, ELECTRICAL CONNECTIONS, GAS CONNECTIONS, AND GROUNDING MUST COMPLY WITH ALL APPLICABLE CODES. IMPORTANT: Save these instructions for the Local Electrical Inspector’s use.
-
Page 2: Table Of Contents
INTRODUCTION (Shown with Low Back Guard Model PRS48LB) WARNING: Improper ® installation, adjustment, The Thermador Professional Ranges are free standing units alteration, service or main- available in a number of configura- tenance can cause injury or tions. Model PRG304 is equipped property damage. -
Page 3: Warning
AVERTISSEMENTS EN FRANCAIS For Residential Use Only ALL-GAS MODELS - PRG304 AND PRG36, DUAL FUEL MODELS PRDS304, PRDS36 AND PRDS48 CET MAN U EL CONTEN IT AVERTISSEMENTS EN FRANCAIS AVERTISSEMENT: AVERTISSEMENT: Couper le courant avant d'installer. DANGER DE Avant de mettre EN MARCHE, soyez certain que tous les RENVERSEMENT controles sont dans la position ARRÊTE. - Page 4 AVERTISSEMENTS EN FRANCAIS AVERTISSEMENT Page 2...
-
Page 5: Important Installation Information
This may be particularly beneficial for those cases, such as a long duct run or heavy usage of the grill, in which improved capturing of the cooking exhaust is desired. ** Thermador offers a choice of remote (VTR1000Q or VTR1400q) or in-hood (VTN1000Q) blowers for use in wall installations. Page 3... -
Page 6: Step 2: Cabinet Preparation
CAUTION: the cooking surface, a The PRDS48 Ranges must be Thermador Low Back or High placed with the oven door Do not install the Model Shelf backguard must be projecting out from the cabinet PRDS48 ranges such that the installed. - Page 7 STEP 2: CABINET PREPARATION CAUTION: Do not install the Model PRDS304 and PRDS48 ranges such that the front surface of the oven door is flush with the cabinet face. A flush installation could result in damage to the cabinets due to high heat. The face of the cabinet should line up with the oven front frame.
- Page 8 STEP 2: CABINET PREPARATION GAS AND ELECTRIC SUPPLY ZONES: FIG. 3a Gas & Electrical Supply Zone for PRG304, PRG36 & PRG48 All-Gas Ranges 5/8" Flex Line to The All-Gas Ranges are factory equipped Appliance Typical placement shown. with a power supply cord with a three-prong Three-Prong, Other placement of Gas grounding plug.
- Page 9 STEP 2: CABINET PREPARATION ELECTRICAL SUPPLY, DUAL FUEL RANGES This is especially critical if the Installation of Dual Fuel ranges junction box in the wall will be must be planned so that the directly behind the junction box rough-in of the junction box for on the unit when the unit is the receptacle or conduit connec- installed.
-
Page 10: Step 3: Unpacking, Moving And Placing The Range
STEP 3: UNPACKING, MOVING AND PLACING THE RANGE Chart A 30" Range 36" Range 48" Range CAUTION: Shipping Weight 335 lbs. 444 lbs. 584 lbs. Proper equipment and adequate manpower must Weight without 285 lbs. 390 lbs. 524 lbs. be used in moving the packing materials range to avoid damage to the unit or the floor. - Page 11 STEP 3: UNPACKING, MOVING AND PLACING THE RANGE • Due to the weight, a dolly with soft wheels should be used to move this unit. The weight must be supported uniformly across the bottom (See Fig. 7). • After transporting the professional range by dolly close to its final location, the range can be tipped back and supported on the rear...
-
Page 12: Step 4: Install Anti-Tip Device
STEP 4: INSTALLING ANTI-TIP DEVICE For all 30" and 36" ranges, an anti-tip device must be in- stalled as per these instructions. WARNING WARNING RANGE TIPPING HAZARD • ALL RANGES CAN TIP • All ranges can tip and injury could •... - Page 13 STEP 4: INSTALLING ANTI-TIP DEVICE Parts Required for Installation of Anti-Tip Device: PRG304 and PRG36 All Gas Ranges (Figures 9 and 10) Thermador Part No. Qty Description FIG. 10 Adjustable Anti-Tip Channel PRG304 15-10-916 Screw, Phillips,#10 x 1-1/2" and PRG36 All-Gas Ranges...
- Page 14 STEP 4: INSTALLING ANTI-TIP DEVICE PRG304 AND PRG36 All-Gas Ranges (Figures 9, 10, 12a 12b and 13) STEP A: Determine the best location for the PRG Mounting Bracket. The bracket may be FIG. 12a PRG36 Wall Mount (0" Clearance) mounted to the wall or floor behind the PLAN VIEW range, offset from either the left or right side wall by 2-3/4"...
- Page 15 STEP 4: INSTALLING ANTI-TIP DEVICE STEP H: Using the 1/4"-20 x 1/2" Hex Head FIG. 13 PRG36 Floor Mount Bolt, Hex Nut and two (2) Flat Washers, securely attach the Adjustable Anti-Tip PLAN VIEW Channel to the existing hole in the flange located at the bottom rear of the range.
- Page 16 STEP 4: INSTALLING ANTI-TIP DEVICE STEP B: Set the bracket on the floor and FIG. 14 PRDS Wall Mount turn it until it is oriented properly. The long channel should be on the top with the free end facing towards you, one set of mounting flanges should be resting horizontally on PLAN VIEW the floor, and the other set of mounting...
-
Page 17: Step 5: Gas Requirements & Hookup
Contact supply. The supply line must not interfere with the the dealer where the unit was purchased or Thermador back of the unit. Make sure the gas supply is turned (800/735-4328). The field conversion kit for all... -
Page 18: Step 6: Electrical Requirements, Connection & Grounding
STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING proper circuit breaker or • Prior to servicing appliance, always • Dual Fuel range models disconnecting the proper fuse. disconnect appliance electrical PRDS304. PRDS36 and supply cord, if so equipped, from PRDS48 can be cord-con- •... - Page 19 STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING Dual Fuel models PRDS304, PRDS36 and PRDS48 must be connected to the power supply utilizing one of the following methods. For all methods of connection, the length of the cord or conduit/wiring must allow the unit to be slid completely out of the cabinet without having to unplug or disconnect the unit from the power supply.
- Page 20 STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING A 3 or 4 conductor supply may be connected to FIG.17 Conductor Securement the terminal block. A 4 conductor supply shall Upper Nut be used only when the range is installed in a Cupped Washer mobile home or where local codes do not permit grounding through the neutral.
- Page 21 STEP 6: ELECTRICAL REQUIREMENTS, CONNECTION & GROUNDING Recommended Grounding Method – All-Gas FIG. 19 Recommended Models PRG304, PRG36 and PRG48 Grounding Method – Models PRG304, PRS36 The 30," 36" and 48" all-gas ranges are factory equipped with a power and PRG48 supply cord with a three-prong grounding plug (with polarized parallel blades).
-
Page 22: Step 7: Backguard Installation
STEP 6: ELECTRICAL REQUIREMENTS, CONNECTIONS & GROUNDING CASE 2: Electrical Connections and Grounding brought out to the junction box on the with a 4-Conductor Power Supply (to be range and connected to the box, per the used only when local codes do not per- instructions. -
Page 23: Step 8: Test And Adjustment
Be certain that burner caps seat properly into CAUTION the alignment slots in the burner bases. Before testing operation of the Thermador recommends that appliance, verify that the unit and the gas supply have been carefully burner adjustments be made by... -
Page 24: To Clean And Protect Exterior Surfaces
STEP 8: TEST AND ADJUSTMENT FIG. 23 PROPER FLAME (APPROX.) * The gas oven infra-red broiler burner has no air shutter and Griddle, Grill, & Gas Oven Burners is not adjustable when used with natural gas. When used on propane gas, an air shutter is attached, but it is not adjustable. -
Page 25: Installer Checklist
INSTALLER CHECKLIST FINAL CHECK LIST ❑ ❑ Burner caps properly seated Manual gas shut off valve ❑ Placement of unit. into burner bases with align- installed in an accessible ment pins engaged. location (without requiring ❑ Specified clearances maintained removal of range). ❑... - Page 26 NOTES Page 24...
- Page 27 NOTES Page 25...
- Page 28 We reserve the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer.